603497
9
Zoom out
Zoom in
Previous page
1/38
Next page
Radar Installation Manual Page 11
2. INSTALLATION
This chapters illustrates the instructions on mechanical and electrical connections of the
Radar and the necessary software settings to operate it.
WARNING
In order for the Radar Antenna to communicate with the Chart Plotter, the software must be
configured as explained in the Par. 2.7.
2.0 INSTALLATION CONSIDERATIONS
Prior to the actual installation of the Radar Antenna, several factors must be considered to
ensure maximum performance (see also Appendix B).
a. The Antenna must be located so that passengers and crew are not exposed to the direct
Radar beam.
b. The Antenna should be mounted on the centerline of your vessel in a location that has
an unobstructed view forward and the rest of the area around the scanner is as
unobstructed as possible.
c. A location as high as practical to improve maximum range is preferable, keeping in mind
that minimum range objects may be overlooked if mounted too high. Large structure or
stacks cause blind spots.
d. Contamination from engine exhaust on the scanner housing reduces Radar perform-
ance.
e. Antennas for GPS, radio communication or other equipment should not be in the Radar
beam (Use non-metallic extension poles to move the active area of Antennas above the
Radar beam).
f. In selecting a location, consider the suitability of the mounting surface. It must be flat
and approximately levelled with the vessel’s water line. The surface must support the
weight of the scanner and have access to the under side for installation of the four
mounting bolts.
g. Consider the cable route from the Antenna to the GPS Chart Plotter’s location. Avoid
routing the interconnecting cable through areas of possible damage from moving
objects, machinery, and exposure to chemicals or high temperature.
NOTE
1. The recommended mounting surface thickness is 3/8 to 1/2 in. (9 mm to 13 mm).
If the mounting surface is thin, the mounting surface must be increased to the recommended
surface thickness.
2. If it is thicker, longer bolts must be purchased.
3. The scanner will be damaged if bolts penetrate more than 9/16 in. (15 mm).
2.1 PREPARE THE RADAR FOR INSTALLATION
Unpack the Radar Antenna and check that the contents correspond to the packing list.
2.1.0 Cable
Do not remove the cover from the unit. There are no connections or adjustments inside the
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Standard Horizon MDS-1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Standard Horizon MDS-1 in the language / languages: English as an attachment in your email.

The manual is 1,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info