603494
35
Zoom out
Zoom in
Previous page
1/42
Next page
Radar Operation Manual Page 37
5. TROUBLESHOOTING
5.0 The Radar page is not available
Configure the I/O setup. Enter the I/O Connections menu, see procedure at Par. 2.7 and
select the Radar on the serial port to which the Radar is connected.
5.1 The message "Turn Radar On" is displayed on the Radar window
· Check the Radar On/Off switch. It is in the off position or has not been wired.
· Verify that the correct serial port is set in the I/O Connections menu, in case try setting
the Radar on another serial port (following procedure shown at Par. 2.7).
· Check that the Radar is connected to the chart plotter, to the same serial port as set
in the I/O Connections menu, in case try connecting it to another serial port.
· Verify that all the connections in the Junction box are done properly.
· Verify using a Voltage Meter that the Radar power supply level at the Junction Box is
at least 12V. The Radar is able to operate with 10V but some volts may be dropped due
to the cable length.
If everything above is correct, try shortening the green and the blue cable coming from the
Radar. If the Radar still doesn’t work you need to call the Standard Horizon Marine Product
support for assistance at (800)767-2450 for assistance.
5.2 After the Radar On/Off Switch is turned on the “Radar warming up”
window counts down but restarts counting down over and over.
The power supply level is too low. This may be caused by battery low, cable too long, cable
section to narrow.
5.3 Too much clutter near the Radar screen center
This is a typical phenomenon with Radar. Echoes from nearby vessel may hit other objects
like other vessels or other objects randomly and reflections can be received by Radar
antenna due to very short distance between the objects. This is normal condition in a port
where nearby targets (such as sailboat masts) may cause multiple reflections. In this case,
increase the SEA clutter and decreasing the GAIN.
If during navigation in open sea the center of the screen is covered by a large spot. If this
happens it means the most probably the Transmission Trigger Delay and/or the Main Bang
Suppression need to be correctly tuned (refer to Par. 3.1).
5.4 The screen center is always covered by a spot
The Transmission Trigger Delay or the Main Bang Suppression needs to be tuned (refer
to Par. 3.1).
5.5 After turning transmission On, the Radar page remains completely black
The Radar is probably not properly tuned. Execute the Automatic Tuning procedure to
restore optimal performance (refer to Par. 3.1).
35


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Standard Horizon CPV350 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Standard Horizon CPV350 in the language / languages: English as an attachment in your email.

The manual is 2,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info