603484

Standard Horizon CPN1010i Manual

171
Zoom out
Zoom in
Previous page
1/188
Next page
Page 172 Owner’s Manual
9.1.2 BACKLIGHT
Each time you move the ShuttlePoint knob to the left, the screen will decrease brightness,
move it to the right to increase brightness.
9.1.3 CARTRIDGES (USED BY STANDARD HORIZON TECHNICIANS)
Internal Data Base Test
To test the Worldwide Background.
SD CARD Test
To test the SD CARD. There are the possible situations:
1. If there is an SD CARD inserted in the slot and there is not a malfunction, the name of
the SD CARD zone and the message "OK" are shown.
2. If there is an SD CARD inserted in the slot, but it is a defective SD CARD, the name of
the SD CARD zone and the message "Faulty" are shown.
3. If there is not any SD CARD inserted in the slot, the message "not present" is shown.
9.1.4 SERIAL PORTS (USED BY STANDARD HORIZON TECHNICIANS)
If you are having problems receiving data from the position-finding instrument, this test
should help determine the problem.
Change Parameters
To change the parameters of the serial interface. This menu allows selecting the Port
(Signal Source) between Port1, Port2, Port3, Port4; the Baud Rate between 300, 1200,
2400, 4800, 9600, 38400, 115200; the Data Bits (Word Length) between 7 or 8, the Parity
between even, odd or none, the Stop Bits between 1 or 2. Default settings are: Port =
PORT2, Baud Rate = 4800, Data Bits = 8, Parity = none, Stop Bits = 1.
Input Data Display
To allow the CPN Series Chart Plotter to act as a computer terminal and display the
incoming data exactly as it is received. If the data displayed on the screen is unrecognizable,
you may have selected the wrong input parameters for your particular receiver, for example,
Baud Rate 9600 instead of Baud Rate 4800. Check your receiver manual to be sure that
you have selected the proper parameter. If the screen is blank, you may have a broken
connection, and no data is being received or you may have connected the device to the other
input port. Use the
key to stop (or continue after pausing) data displaying, press the
ShuttlePoint knob to show data in hex or ASCII mode and the key to exit.
Loop-Back Test
This is a special test done during the production phase to check the serial ports integrity.
A special connector is required.
… 171 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Standard Horizon CPN1010i at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Standard Horizon CPN1010i in the language / languages: English as an attachment in your email.

The manual is 17,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info