603509
110
Zoom out
Zoom in
Previous page
1/166
Next page
Page 112 CPF180i and CPF300i
XTE Alarm : Alerts when the vessel is deviating from a defined course. Available selections: 0.00 to
9.99NM.
Depth Alarm : Alerts when the received depth Value is lower than the selected value. Available selections:
0000 to 3000FT.
Anchor Alarm : Alerts when the ships moves off a selected locations by a selected distance. Available
selections: 0.00 to 9.99NM.
Audble Alarm : Enables or disables the alarm beep.
Grounding Alarm : This function looks ahead of the vessels heading to see if a potential danger exists. When
the Grounding Alarm is enabled the GPS Chart Plotter will draw a triangle in front of the vessel
on the Chart page showing the area that is being searched as shown below. The depth and
range (distance) of the area the GPS Chart Plotter looks ahead for a shallow area can be set
using this function.
Grounding Alarm Range : This function allows setting the distance of the grounding alarm zone (the length of the sector
to be detected) among the 0.25, 0.5, 1.0 Nm selections. When a depth or any of the searched
objects is found in the scanned area, a tick marker is printed on the relative box in the Grounding
Alarm Report page to identify which dangerous objects have been currently detected.
Grounding Alarm Report: This function allows displaying a report of the dangerous objects currently detected.
The following warning appears when the Grounding Alarm is enabled:
NOTES
The Grounding Alarm function is available only if a NT
+
/MAX C-CARD is inserted. It also affects the
screen redraw speed so we suggest to disable it when not used.
When any of the objects checked are found for the first time, the GPS Chart Plotter shows a pop
up window to alert the user of the possible danger. The name of each new dangerous object found
is reported in the warning window. In the Grounding Alarm Report page the relative item has a tick
marker next to it, to identify the dangerous object currently detected. If in the next search cycle the
same objects are found again, the alarm window will not be shown. Instead, if in the next searches
the objects found before are no longer detected, their relevant item in the Grounding Alarm Report
page is cleared (note that in this case, if the same object type is found again later, the Alarm will
be shown). The GPS Chart Plotter shows an icon on the charts that identifies when a Grounding
Alarm is detected.
Figure 13.3 - Grounding Alarm
13.4 SIMULATION
The built-in Simulator function allows you to become proficient in the use of the GPS Chart
Plotter, see the Simulation menu below:
Simulation Mode : Three selections:
a. Off - turn the simulation mode Off
b. On - enable the simulator mode, where the speed and course are adjusted by
entering in values in the Course and Speed selection discussed later in this table.
c. Route - this selection allows you to navigate to a saved route.
Course : To start the simulator you can insert the Course value.
110


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Standard Horizon CPF300i at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Standard Horizon CPF300i in the language / languages: English as an attachment in your email.

The manual is 3,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info