603491
13
Zoom out
Zoom in
Previous page
1/121
Next page
CP590 Page 15
3. Connect one of the Accessory cables to the PWR ACC1 connector on the rear panel.
The other Accessory cable is used to connect to ACC2 connector.
4. This cable has many wires, however only the RED and BLACK wires are used to
connect to a switched battery supply. Refer to the image below. For additional
connections refer to NMEA connections.
GPS ANT
PWR & ACC 1
ACC 2
VIDEO OUT VIDEO IN 1 VIDEO IN 2
Green
Gray
Black
Red
Blue
Brown
White
Yellow
PWR ACC 1 Cable
Fuse
Switch
+
BATTERY
-
2.4.1 NMEA Connections
The CP590 PWR ACC1 connector is also used to attach NMEA devices* such as AIS
Receivers, digital instruments, Personal Computers, Autopilots and the optional FF525
Black Box Fish Finder.
*NOTE
RS232 not opto-isolated electrical interface.
*NOTE: AIS RECEIVER OPTION
For more information on AIS refer to Section 14.
The CP590 has to be set up to be able to receive NMEA information from the AIS Receiver. The
CP590 reads the AIS NMEA message VMD, type 1, 2, 3 and 5 for AIS Class A and type 18, 19,
24 for AIS Class B. Select the used Port and transmission speed by following the procedure:
1. From the Chart page, press [MENU], move the ShuttlePoint knob to highlight
SETUP MENU
and press [ENT].
2. Move the ShuttlePoint knob to highlight
ADVANCED SETUP and press [ENT] or move the
ShuttlePoint knob to the right.
3. Move the ShuttlePoint knob to highlight IN/OUT CONNECTIONS and press [ENT] or move the
ShuttlePoint knob to the right.
4. Move the ShuttlePoint knob to highlight PORT1 INPUT and press [ENT] or move the
ShuttlePoint knob to the right.
5. Move the ShuttlePoint knob up/down to select
AIS 38400 and press [ENT] or move the
ShuttlePoint knob to the right.
6. Press [CLR] or move the ShuttlePoint knob to the left until the Chart page is shown.
**NOTE: AUTOPILOT CONNECTION
Care must be taken when connecting the CP590 to an Autopilot. Normally Port3 (Yellow wire) will
be used to connect to an Autopilot input, however older Autopilots may not be able to read the
sentences due to the talker ID that is being used (II Integrated Instrument). If the Autopilot
connections are made to Port3 (Yellow wire) and the Autopilot is not reading the sentences, change
the connections to Port1 (Brown) or Port2 (White) and change the sentences to APA, APB, XTE,
COG and BOD.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Standard Horizon CP590 - GPS Chart Plotter at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Standard Horizon CP590 - GPS Chart Plotter in the language / languages: English as an attachment in your email.

The manual is 8,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info