603479

Standard Horizon CP190i - GPS Chart Plotter Manual

97
Zoom out
Zoom in
Previous page
1/144
Next page
Page 98 CP190i and CPF190i
a. Off - turn the Simulation Mode Off
b. On - enable the simulator mode, where the speed and course are adjusted by
entering in values in the Course and Speed seection discussed later in this table.
c. Route - this selection allows you to navigate to a saved route.
Course : To start the simulator you can insert the Course value.
Speed : To start the simulator you can insert the Speed value.
Date : To start the simulator you can insert the date.
Time : To start the simulator you can insert the time.
Cursor Control : Enables (On)/disables (Off) the cursor control. Moving the ShuttlePoint knob up or down will
change the SOG and left or right will change the COG of the simulated vessel.
Demo Mode : In Demo mode the GPS Chart Plotter automatically places a Destination point on the Chart
page and simulates navigation to the point. Also, the active page changes automatically
every 10 seconds. The pages are shown in the following order: Start-up screen, GPS Status,
Chart/Compass tape, Chart/Fish Finder, Full page Fish Finder, Full page Radar, Naviga-
tion, Highway, Celestial, NMEA. Once the Demo mode is enabled, pressing any key it is
possible to temporally exit and returns to GPS Chart Plotter normal operation, but if you do
not touch any key for 30 seconds Demo Mode restarts.
13.4.0 Navigating a Route in Simulation Mode
This selection allows you to navigate to a saved Route to see how data windows on the Chart
page and how the Navigation and Highway pages operate.
1. Create a Route. Refer to Par. 9.0 Route.
2. Press [MENU], move the ShuttlePoint knob to highlight
SETUP MENU and press
[ENT].
3. Move the ShuttlePoint knob down to highlight
ADVANCED SETUP, then press [ENT].
4. Move the ShuttlePoint knob to highlight
SIMULATION and press [ENT].
5. Move the ShuttlePoint knob to highlight
SIMULATION MODE and press [ENT] to show
a popup window.
6. Move the ShuttlePoint knob to highlight
ROUTE and press [ENT] which will show a
popup window with the Route(s) that are stored in the GPS Chart Plotter’s memory.
7. Highlight the desired Route and press [ENT].
8. Move the ShuttlePoint knob to highlight
SPEED and press [ENT].
9. Enter in the speed you want to vessel to travel at in Simulation Mode, by moving the
ShuttlePoint knob left or right to select a number and up or down to change a number.
10. When the speed is adjusted, press [ENT].
11. Press [CLR] multiple times until the Chart page is shown.
13.5 DSC POLLING
This menu is used to enable or disable features related to the DSC function.
Auto Position : Selects between Manual or Auto. See also the Par. 12.8.1. When Auto Position item is set to
Manual and receiving the Position Request, the Position Request popup window is not displayed
and the cursor does not move to the position of the received Position Request data point.
Otherwise when Auto Position item is set to Auto, the GPS chart plotter works as follows:
1 : when receiving the Position Request, the Position Request popup window s displayed;
: when selecting VIEW ON CHART, the position is indicated on the chart marked with “P”.
The cursor is moved to the point “P” and shows the point in the center of the screen;
3 : when moving the cursor from “P”, the location can be confirmed. At this time, the same
MMSI Position Request data that were received before are remaining and displayed.
Auto Info : Enables or disables the Auto Info. This selection is available only when Auto Position is set to
Manual. If Auto Info is set to On, when receiving the Position Request it is possible to center the
cursor over the top of the Position Request icon and show the Position Request popup window
… 97 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Standard Horizon CP190i - GPS Chart Plotter at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Standard Horizon CP190i - GPS Chart Plotter in the language / languages: English as an attachment in your email.

The manual is 8,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info