Manual Stadler Form Roger Big (page 9 of 76) (English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian, Finnish)

807169

Zoom out

Zoom in

1/76

Setting up / operation

1. Remove the textile pre-filter (1) by taking hold of the top on both sides

and pulling it forwards. Take the Dual FilterTM (2) from its housing (3) and

remove the plastic film. Set the Dual FilterTM (2) in place so that the two

textile tabs are visible on the front side. Arrows on the top of the filter

(2) indicate the direction in which the filter must be inserted. Important:

Roger big has a textile pre-filter on both sides and a Dual FilterTM, there-

fore both Dual FilterTMs must be unpacked and inserted.

2. Refit the textile pre-filter (1) by inserting the positioning aids near the

bottom of the textile pre-filter (1) into the notches on the housing (3) and

then tilting the textile pre-filter (1) towards the housing until it is locked

into place at the top by the magnets on the housing (3). Make sure that

the LED cylinder at the front towards the bottom of the appliance is

inserted in the hole on the pre-filter.

3. Place Roger/Roger little / Roger big to the desired location on a flat

surface, ideally centered in the room. This allows air to be supplied from

all sides.

4. Connect the mains cable (4) to its connection (5) on the unit and then to

a suitable power outlet.

5. Turn on Roger/Roger little/ Roger big by pressing the on/off button (7).

The controls and the display light up in sequence from right to left. If

no further buttons are pressed within 10 seconds, the display goes out

again. Otherwise, visibility is extended by a further 10 seconds. Pressing

the on/off button (6) or the controls lights them back up. To turn Roger/

Roger little / Roger big off, press the on/off button (6) for two seconds.

6. Air quality is measured by means of various sensors (Roger / Roger big

= gas and particle sensor PM2.5 / Roger little = gas sensor) and is indi-

cated by the air quality indicator (7) in front of the textile pre-filter (1).

The blue LED means good air quality. The orange LED shows medium air

quality, and the red LED shows poor air quality. If the device is switched

on again, the display will light up in orange for the first three minutes.

The display then changes to the air quality currently measured (blue,

orange or red).

7. You can change the speed level by pressing the button for the selection

of the speed level (8) (one LED for level 1, two LEDs for level 2, etc.).

Increasing the speed level is useful when the air quality indicator (7)

indicates decreasing air quality (blue for good air quality, orange for me-

dium air quality and red for poor air quality). For optimal air purification,

we recommend activating auto mode (9).

8. Pressing the button for auto mode (9) automatically adjusts the speed

level to the current air quality (steps 1–4). If the air quality deteriorates,

the device automatically selects a higher speed level. The display shows

“Auto” when auto mode is activated.

9. By pressing the button for the timer (10) you can set the operating time

for between one and seven hours (for example, 3 h = 1 h and 2 h LEDs lit,

7 h = 1 h, 2 h and 4 h LEDs lit). The selected time is displayed above the

timer button with white LEDs. Press once to set the operating time to

1 h, press the button again for 2 h, and so on. The remaining time is indi-

cated by the illuminated LEDs above the timer button. The unit switches

off automatically after the set operating time has elapsed. If no LEDs are

lit above the timer, the unit is set to continuous operation.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stadler Form Roger Big in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3.97 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stadler Form Roger Big Manual

Product: