Manual Stadler Form Karl (page 7 of 77) (English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian, Finnish)

807104

Zoom out

Zoom in

1/77

Setting up / operation

1. Place Karl / Karl big in the desired location on a flat surface. Lift off

the upper part (3) of the device to fill the lower part (4) with clean cold

tap water up to the maximum mark (17) directly from the tap or use a

clean watering can to fill the container via the opening for refilling (13).

Caution: no water may enter the air outlet opening (14)! If you filled the

lower part directly from the tap, put the upper part (3) back on the lower

part (4), making sure that they fit together properly. Connect the power

cable (1) to the power adapter connection (2) on the device first of all and

then to a suitable socket outlet.

2. Start the appliance by pressing the On/Off button (5). The white LED

should then light up. If a red lamp (11) lights up however, this indicates

no water in the appliance.

3. You can use the hygrostat to set the desired air humidity. To do this,

press on the button for the hygrostat (6). You can choose between the

following levels: 40 % relative air humidity (1 white LED), 45 % (2 white

LEDs), 50 % (3 white LEDs), 55 % (4 white LEDs), constant operation

“CO” (5 white LEDs). If the LEDs are flashing, this indicates that the

desired air humidity has already been reached. Please note that the hy-

grostat needs about 3 seconds to measure the current humidity in the

room. The hygrostat will switch the device on again automatically as

soon as the relative humidity in the room drops below the set value.

We recommend that you set your room humidity to 45 – 60 % (comfort

range).

4. Press the button for selecting the humidification level (7) to change the

fan speed (levels 1–4). Pressing once increases the speed by one level.

If you would like to increase the speed by another level, press again.

The setting chosen is indicated by the number of LEDs illuminated un-

derneath the humidification level button (7) (1 LED for level 1, 2 LEDs for

level 2, 3 LEDs for level 3, 4 LEDs for Turbo). Level 2 is the default setting.

5. Press the auto mode button (8) to activate the auto mode. The LED be-

low the auto mode button lights up. In auto mode, the appliance auto-

matically maintains the desired humidity level. First, set the hygrostat

(6) to the desired humidity (40 / 45 / 50 or 55 %). The auto mode can

not be activated when the hygrostat (6) is set to continuous operation

(5 LEDs lit). The lower the current humidity, the higher the speed of the

fan is set automatically. The closer the current humidity is to the desired

value, the lower the speed level is selected (e.g. if desired humidity is

45 % and current humidity is below 34 %, level 3 is selected, from 35-

40 % = level 2, from 41-45 % = Level 1). As soon as you press the button

for changing the humidification level (7) (or the auto mode button (8)

again), auto mode is deactivated.

6. If you find the lamps too bright (in a bedroom for example), you can re-

duce the brightness of the LEDs by pressing the dimmer button (9). You

can choose between three different modes:

• Normal mode (default mode)

• Dimmed mode (press once)

• Lights-out mode (press twice)

• By pressing the dimmer button once more, you can go back into nor-

mal mode.

If there is no water in the appliance, the red LED (11) lights up in all

modes (normal and night mode). The red light can not be dimmed.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stadler Form Karl in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3.51 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stadler Form Karl Manual

Product: