9
Using the angle grinder
It is extremely important that you do not forget to read the safety
requirements before using the device for the first time.
Safety Requirements Specific to the SAG 230 E:
• Check that the speed marked on the blade is equal to or greater than
the speed indicated on the angle grinder.
• Verify that the dimensions of the blade are compatible with those of
the angle grinder.
• Maintain abrasive blades with care and handle them in accordance
with the instructions provided by the manufacturer.
• Before use, carefully check to see that no cracking, chipping, or other
defects are present on the blade. Never use a damaged blade with the
device.
• Ensure that the abrasive wheel is correctly mounted and assembled in
accordance with the instructions provided by the manufacturer.
• Utilise disc flanges supplied with the abrasive tool if necessary
• Before using the grinder, check to see that the abrasive wheel is
correctly mounted and allow the device run unimpeded for thirty
seconds in a safe position. In the case of excessive vibration, turn the
angle grinder off immediately and examine it thoroughly to determine
the cause.
• If a safety-guard is provided with the tool, be sure to use it at all
times while operating the angle grinder.
• Never use bushings or large-hole adaptors for the abrasive tools that
were not provided by the manufacturer.
• Ensure that any wire wheel is compatible with size the axis, if the tool
is to be used with a wire wheel.
• Ensure that the work piece is supported sufficiently and held firmly in
place before using the angle grinder.
• Take extra care that sparks given off during the work do not cause any
undue risk, in particular that no one is injured and that no flammable
substances are ignited.
• Make sure that the air-slits of the ventilator are kept open when
working in a dusty or dirty environment. Should it become necessary
to using the angle grinder
• clear material from the openings, first separate the work tools from
machine (use only non-metal objects) and take extra care to avoid
damaging any internal components.
• Always use safety glasses and ear protectors. Other personal safety
items such as full-face visors, work gloves, helmet and aprons are
highly recommended.
• Be aware that the saw continues to rotate after the device is
switched off.
Safety
requirements
G
8
Technical properties
Mains voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230 V
Current strength. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11,3 A
Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50-60 Hz
Nominal Capacity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2400 W
Speed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6500 tr/min
Insulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class II
Diameter saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230 mm
Weight with safety-guard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6.55 kg
Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .495 x 104 x 133 mm
Cable length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 m
Noise and vibration
Values are within the requirements according to European norms
EN 50 144.
LP (Acoustic sound pressure) 102 dB (A)
LW (Acoustic capacity) 115 dB (A)
Wear ear-protectors!!
Weighed quadratic average value of the acceleration conforms with
EN 50 144 is 3 m/s
2
Conformity Declaration
This product conforms to the necessary requirements according to
the norms: EN 50 144, EN 55 014, conforms to the norms 73/23 EEC,
89/336/EEC, 98/37/EEC.
Frank Vanaudenaerde Ruben Bernaert
ITW HEGER
Cardijnlaan 3
B-8600 DIKSMUIDE
SAG 230E
