583956
11
Zoom out
Zoom in
Previous page
1/20
Next page
16
Treadmill
XT485
17
Treadmill
XT485
The 1/4-mile track (one lap) will be displayed around the dot matrix window. The ashing
segment indicates your progress. Once the 1/4-mile (Metric - 0.4k) is complete this feature will
begin again. There is a lap counter in the message window for monitoring your distance.
1/4 Mile Track
The Pulse (Heart Rate) console window will display your current heart rate in beats per minute
during the workout. You must use both stainless steel sensors on the front cross bar or the heart
rate transmitter chest strap to display your pulse. Pulse value displays anytime the upper display is
receiving a Pulse signal. You may not use the Grip Pulse feature while in Heart Rate Programs.
Note: Refer to Important Safety Instructions (page 2) concerning Pulse Grip operation.
Pulse Grip Feature
Displays the cumulative calories burned at any given time during your workout.
Note: This is only a rough guide used for comparison of different exercise sessions, which cannot be used for
medical purposes.
Calorie Display
The console has built-in Speakers. You may plug an Audio Source (CD player, MP3, Computer,
etc.) into the Jack on the right side of console. There is no volume control on the console. The
volume must be controlled on the Audio Source.
Speakers
1. Display will automatically turn off (go to sleep) after 30 minutes (no key
operations). The treadmill will draw very little current in sleep mode (about as much as your
television when it is turned off).
2. Remove the tether cord.
3. Turn off the main switch on the front of the treadmill, below the motor cover.
To Turn Treadmill Off
To the right of the Stop button there is a Handrail control switch and an indicator light next to
it When the indicator light is lit, the handrail switches are disabled. This allows you to use the full
length of the handrails without fear of activating the speed or elevation controls.
Handrail Buttons Disable Switch
STEP 1: Press the desired program (Hill, Fat Burn, Cardio, Strength, or
Interval) key. Press Enter to select the program. The display will prompt you
through the programming or you can just press Start to begin the program
with default values.
STEP 2: If Enter was pressed, the Message Center will now be blinking a value,
indicating your Age (default is 35). Entering your correct age affects the heart
rate Bar Graph Display and the Heart Rate programs. Use the + / - keys to
adjust, then press Enter. Your age determines your recommended maximum
heart rate. Since the Bar Graph Display and the Heart Rate features are based
on a percentage of your maximum heart rate, it is important to enter the
correct age for these features to work properly.
STEP 3: The Message Center will now be blinking a value, indicating your Body
Weight (default is 150 lbs.). Entering the correct body weight will affect the
calorie count. Use the + / - keys to adjust, then press Enter. A note about
the Calorie display: No exercise machine can give you an exact calorie count
because there are too many factors which determine exact calorie burn for a
particular person. Even if someone is the exact same body weight, age and
height, their calorie burn may be very different than yours. The Calorie display
is to be used as a reference only to monitor improvement from workout to
workout.
STEP 4: The Message Center will be blinking a value, indicating Time (the default
value is 30 minutes). You may use any of the + / - keys to adjust the time. After
adjusting, or to accept the default, press Enter. (Note: You may press Start at
any time during the programming to start the program).
STEP 5: The Message Center will now be blinking the preset top speed of the
selected program (3 mph or 5 kph). Use the Speed + / - keys to adjust, then
press Enter. Each program has various speed changes throughout; this allows
you to limit the highest speed the program can reach.
STEP 6: The Message Center will be blinking the preset top incline of the
selected program (6.0%). Use the Incline + / - keys to adjust, then press
Enter.
You are now done programming data and may press Start to begin your
workout or Enter to go back one level to change data entered in the
programming phase.
To Select and Start A Preset Program
Programmable Features
The
XT485
offers nine factory preset-programs, two user dened programs and one
Manual program. Each preset program has a maximum speed level that is displayed when a
desired workout is chosen. The maximum speed that the particular program will achieve will be
displayed in the Speed window. Also included are two user programs (User 1 and User 2)
for custom workouts.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Spirit XT485 2011-2012 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Spirit XT485 2011-2012 in the language / languages: English as an attachment in your email.

The manual is 8,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info