584057
28
Zoom out
Zoom in
Previous page
1/33
Next page
XT375 / XT475 / XT675
27
Belt and Bed - Your treadmill uses a very high-efficient low-friction bed. Performance is
maximized when the bed is kept as clean as possible. Use a soft, damp cloth, or paper towel,
wipe the edge of the belt and the area between the belt edge and the frame. Also reach as far
as practical directly under the belt edge. This should be done once a month to extend belt and
bed life. A mild soap and water solution along with a nylon scrub brush will clean the top of the
textured belt. Allow to dry before using.
Belt Dust - This occurs during normal break-in or until the belt stabilizes. Sometimes the
black dust from the belt will appear on the floor behind the treadmill, this is normal.
General Cleaning - Dirt, dust, and pet hair can block air inlets and accumulate on the running
belt. Please vacuum underneath your treadmill on a monthly basis to prevent excess build-up
of dirt that can get sucked up and get into the inner workings under the motor cover. Once a
year, you should remove the black motor hood and vacuum out dirt that may accumulate.
UNPLUG POWER CORD BEFORE THIS TASK.
BELT ADJUSTMENTS:
Tread-belt Tension Adjustment - Belt tension is not critical for most users. It is very
important though for joggers and runners in order to provide a smooth, steady running surface.
Adjustment must be made from the rear roller with the 6 mm Allen wrench provided in the
parts package. The adjustment bolts are located at the end of the step rails as shown in the
diagram below.
Tighten the rear roller only enough to prevent slippage at the front roller. Turn the tread-belt
tension adjusting bolts 1/4 turn each and inspect for proper tension by walking on the belt and
making sure it is not slipping or hesitating with each step. When an adjustment is made to the
belt tension, you must be sure to turn the bolts on both sides evenly or the belt could start
tracking to one side instead of running in the middle of the deck.
DO NOT OVERTIGHTEN – Over tightening will cause belt damage and premature bearing
failure. If you tighten the belt a lot and it still slips, the problem could actually be the drive belt -
located under the motor cover - that connects the motor to the front roller. If that belt is loose it
feels similar to the walking belt being loose. Tightening the motor belt should be done by a
trained service person.
General Maintenance
Note: Adjustment is through small hole in end cap.
Tracking / Tension
Adjustment
Tracking / Tension
Adjustment
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Spirit XT475 2007 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Spirit XT475 2007 in the language / languages: English as an attachment in your email.

The manual is 0,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info