Manual Spirit XT-185 (page 28 of 30) (English)

518623

Zoom out

Zoom in

1/30

Treadmill

XT185

If the calibration does not pass you may need to check the speed sensor alignment.

1. Remove the motor cover hood by loosening the 8 screws that hold it

in place. Set it aside.

2. The speed sensor is located on the left side of the frame, right next to the

front roller pulley (the pulley will have a belt around it that also goes to the

motor). The speed sensor is a small rectangular shaped black box with a

wire connected to it.

3. You will see a magnet on the outside edge of the pulley; make sure the

speed sensor is aligned with the center of the magnet when it passes by.

There are two a screws that hold the sensor in place that need to be

loosened to adjust the sensor. Re-tighten the screws when nished.

The console has built in maintenance/diagnostic software. The software will allow you to change

the console settings from English to Metric and turn off the beeping of the speaker when a key

is pressed for example. To enter the Engineering Mode Menu press and hold down the Start,

Stop and Enter keys, then insert the safety key. Keep holding the keys down until the Message

Center displays Engineering Mode Menu. Press the Enter button to access the menu below:

a. Key Test (Will allow you to test all the keys to make sure they are functioning)

b. Security (Allows the keypad to be locked to prevent unauthorized use)

c. Functions (Press Enter to access settings and Up arrow to scroll)

i. Display Mode (Turn off to have the console power down automatically after 30 minutes of inactivity; leave

on to display all lights while the power is on)

ii. Motor Test (Press Enter to run the resistance motor up and down in a continuous loop. Display shows

level setting and position sensor reading. Press Stop to end test.)

iii. Beep (Turns off the speaker so no beeping sound is heard)

iv. Units (Sets the display to readout in English or Metric display measurements)

v. ODO Reset (Resets the odometer)

vi. Pause Mode (Turn on allow 5 minutes of pause, turn off to have the console pause indenitely)

d. LCD Test (Tests all the display functions)

Adjusting The Speed Sensor

Engineering Mode Menu

1. Remove the safety key

2. Press and hold down the Start and Fast + buttons and replace the safety key. Continue to hold the

Start and Fast key until the window displays “Factory settings”, then press the Enter key.

3. You will now be able to set the display to show Metric or English settings (Miles vs. Kilometers).

To do this, press the Up or Down key to show which you want, then press Enter.

4. Make sure the wheel size diameter is 2.30 then press Enter

5. Adjust the minimum speed (if needed) to 0.5 and then press Enter

6. Adjust the maximum speed (if needed) to 10.0 and then press Enter

7. Adjust the maximum elevation (if needed) to 12 and then press Enter

8. Grade return – On (This allows the incline to return to zero when Stop is pressed. For sale in

Europe, EU standards require this to be off)

9. Press Start to begin calibration. The process is automatic; the speed will start up without warning, so

do not stand on the belt.

Calibration Procedure

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Spirit XT-185 in the language / languages: English as an attachment in your email.

The manual is 3,38 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Spirit XT-185

Spirit XT-185 User Manual - Dutch - 9 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Spirit XT-185 Manual

Product: