Please record the Serial Number of this fitness product in the space provided below. The serial
number is located on the console mast frame under the console mast cover, which needs to be
removed to gain access.
Serial Number_______________________________________
REGISTER YOUR PURCHASE
The self-addressed product registration card must be completed in full and returned to
Spirit Manufacturing, Inc or visit: www.spiritfitness.com/warranty.asp to register online.
Ver.A
CONGRATULATIONS ON YOUR
NEW ELLIPTICAL AND WELCOME
TO THE SPIRIT FAMILY!
Product Registration
XE195 / XE295 Elliptical
3
WARNING - Read all instructions before using this appliance.
■Do not operate
elliptical
on deeply padded, plush or shag carpet. Damage to both
carpet and
elliptical
may result.
■Keep children away from the
elliptical
. There are obvious pinch points and other
caution areas that can cause harm.
■Keep hands away from all moving parts.
■Never operate the elliptical if it has a damaged cord or plug. If the elliptical is not working
properly, call your dealer.
■Keep the cord away from heated surfaces.
■Do not operate where aerosol spray products are being used or where oxygen is
being administered. Sparks from the motor may ignite a highly gaseous environment.
■Never drop or insert any object into any openings.
■Do not use outdoors.
■To disconnect, turn all controls to the off position, then remove the plug from the outlet.
■Do not attempt to use your
elliptical
for any purpose other than for the purpose it is
intended.
■The hand pulse sensors are not medical devices. Various factors, including the user’s
movement, may affect the accuracy of heart rate readings. The pulse sensors are
intended only as exercise aids in determining heart rate trends in general.
■Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable
for use on your
elliptical
. Quality athletic shoes are recommended to avoid leg fatigue.
SAVE THESE INSTRUCTIONS - THINK SAFETY!
Important Safety Instructions
XE195 / XE295 Elliptical
4
WARNING!
●
NEVER remove any cover without first disconnecting AC power supply.
●
If A.C. voltage varies by ten percent (10%) or more, the performance of your elliptical may
be affected. Such conditions are not covered under your warranty. If you suspect the
voltage is low, contact your local power company or a licensed electrician for proper testing.
●
NEVER expose this
elliptical
to rain or moisture. This product is NOT designed for
Use outdoors, near a pool or spa, or in any other high humidity environment. Maximum
environmental ratings are 40-120 degrees Fahrenheit, 95% humidity non-condensing (no water
droplets forming on surfaces).
●
NEVER operate this elliptical without reading and completely understanding the results of
any operational change you request from the computer.
●
Understand that changes in resistance do not occur immediately. Set your desired level on
the computer console and release the adjustment key. The computer will obey the
command gradually.
●
NEVER use your elliptical during an electrical storm. Surges may occur in your household
power supply that could damage elliptical components.
●
Use caution while participating in other activities while using your elliptical such as watching
television, reading, etc. These distractions may cause you to lose balance and may result in
serious injury.
●
Always hold on to a handrail or hand bar while making control changes.
Your new elliptical is engineered and manufactured to the strictest industry standards and
tolerances. An inherent problem with elliptical trainers, which affects all manufacturers of these
products, is the multitude of moving linkages and parts. Even with the tightest mechanical
tolerances there still could be a slight amount of play between some parts. This inherent play can
result in slight noises during use such as clicks and small thumps. Please expect that the elliptical
will not be completely silent.
Important Electrical Information
Important Operation Instructions
Things To Know
XE195 / XE295 Elliptical
5
Assembly Pack Check List XE195
#66. M5 x 10mm
Phillips Head Screw (4pcs)
#103. 3/8" x 3/4"
Hex Head Bolt (2pcs) #60. 3/8" x 2-1/4"
Hex Head Bolt (1pc)
#96. 3/8" x 2T
Split Washer (1pc)
#84. 3/8" x 23 x 1.5T
Curved Washer (2pcs)
#79.5/16"x23mm
Flat Washer (2pcs)
#59. 5/16"x15m/m
Hex Head Bolt (2 pcs)
#83. ψ17mm
Wave Washer (2 pcs)
#104. 5/16” x 1-1/4”
Hex Head Bolt (2 pcs)
#80. 5/16" x 20mm
Flat Washer (2 pcs)
#71. 5/16" x 7T
Nylon Nut (2 pcs)
Step 3
Step 2
Step 1
XE195 / XE295 Elliptical
6
#87. ψ3.5x12m/m
Sheet Metal Screw (10pcs)
#105.M5 x 15m/m
Phillips Head Screw (17pcs)
#108. Phillips Head Screw Driver (1 pc) #107. Short Phillips Head Screw Driver (1 pc)
#109. 12m/m Wrench (1pc)
#106. 13/14m/m Wrench (1pc)
Tools
Step 4
XE195 / XE295 Elliptical
7
STEP 1: CONSOLE MAST ASSEMBLY
1.
Locate the Console Mast (12) and Console Mast Cover (41) and slide the Cover onto the
mast as far as it will go. Make sure the Console Mast Cover is facing the correct way.
2. Unravel and straighten out the Computer Cable (31) and feed it into the bottom of the console
mast tube and out of the top opening.
3. Install the Console Mast into the receiving bracket in the top of the Main Frame. NOTE: there
is one bolt already installed in the receiving bracket that will engage with the slot at the bottom
of the Console Mast. This needs to be tightened at the end along with the three other console
mast bolts.
Do not pinch the wire harness during this step.
4. Put one 3/8" x 2T Split Washer (96) onto the 3/8" x 2-1/4" Long Hex Head Bolt (60), and the
two 3/8" x 23mm Curved Washers (84) onto the two 3/8" x 3/4" Short Hex Head Bolts (103).
Install the Long Hex Head Bolt (60) through the left side of the receiving bracket into the
Console Mast and the short bolts (103) through the front.
Assembly Instructions XE195
XE195 / XE295 Elliptical
8
5. With the 13/14mm Wrench tighten the three bolts, and the fourth bolt which is pre-installed,
firmly. These bolts should be tightened as much as you possibly can.
6. There will be three electrical wire connectors at the top opening of the console mast, two 2 pin
connectors for hand pulse sensors (36), one 10 pin connector for main wire harness (31) and
one connector for the handle bar resistance switches (145). Connect these to the mating
connectors on the back of the electronic Console (30). The connectors are keyed, you cannot
plug them in the wrong way so do not force them. The two, 2 pin connectors can be plugged
into either connector on the back of the console.
7. Storing the excess wire back into the Console Mast, carefully install the Console onto the
mounting plate of Console Mast and secure using the four M5 x 10mm Phillips Head Screws
(66).
Make sure the wires do not get pinched between the console and mounting plate.
STEP 2: HANDLE BAR ASSEMBLY
1. Install the two 17mm Wave Washers (83) onto the Left and Right side of the Handle Bar axle.
2. Slide the Left (10) and Right (11) Handle Bars onto the appropriate side of the axle. The
handlebars have a small sticker on them indicating
L
(left) and
R
(right).
3. Put the two 5/16" x 23mm Flat Washers (79) onto the two 5/16" x 15mm Hex Head Bolts (59)
and install in the threaded holes in the ends of the axle.
XE195 / XE295 Elliptical
9
STEP 3: CONNECTING ARM ASSEMBLY
1. Align the hole in the rod end of the left Connecting arm (8) with the hole in the bracket of the
left Handle Bar (10). The rod end should be on the inner side of the Handle Bar bracket. Make
sure the ty-wrap is removed from the rod end and the sleeve spacer (22) does not fall out
during assembly. Take one 5/16" x 1-1/4" Hex Head Bolt (104) and install it through the Handle
Bar bracket and the rod end. Install one 5/16" x 20 x 1.5T Flat Washer (80) and one 5/16" x
7mm Nylon Nut (71) on the 5/16" x 1-1/4" Hex Head Bolt (104) and tighten as tight as possible
using the two12m/m Wrenches provided. Repeat the procedure for the right side Pedal
Connecting Arm.
XE195 / XE295 Elliptical
10
STEP 4: PLASTICS ASSEMBLY
1. Install the Connecting Arm Covers (2 each 57, 58) over the connection of the rod end and
Handle Bars with four M5 x 15m/m Screws and two 3.5x10m/m Self Tapping Screws by using
the Short Phillips Screw Driver.
2. Install the two Wheel Covers (52) using the four M5x15m/m Phillips Head Screws (105).
3. Locate the two Rear Stabilizer Covers (19,20) and two Middle Stabilizer Covers (19,20) for the
Rear Rail Assembly and install with four M5 x 15m/m Screws (105). Then install front stabilizer
cover (49) with two M5 x 15m/m Screws (105).
4. Install the Front Handle Bar Covers (54-1 left, 55-1 right) and Rear Handle Bar Cover (54 left,
55 right) over the Handle Bar axle connections with the six 3.5x10m/m Self Tapping Screws.
5. Install the front (122) and rear (121) console mast covers with three M5 x 15m/m Screws (105)
and two 3.5x12m/m Sheet Metal Screw (87).
XE195 / XE295 Elliptical
11
Assembly Pack Check List XE295
#66. M5 x 10mm
Phillips Head Screw (4pcs)
#103. 3/8" x 3/4"
Hex Head Bolt (2pcs)
#60. 3/8" x 2-1/4"
Hex Head Bolt (1pc)
#96. 3/8" Split
Washer (1pc)
Step 1
#97.3/8" x 30mm
Flat Washer(2pcs)
#103. 3/8"x3/4"
Hex Head Bolt (2 pcs)
#81. 25mm
Wave Washer (2pcs)
#84. 3/8" x 23mm
Curved Washer (2pcs)
Step 2
#80. 5/16" x 20 x 1.5T
Flat Washer (2 pcs)
#104. 5/16” x 1-1/4”
Hex Head Bolt (2 pcs)
#71. 5/16"
Nylon Nut (2 pcs)
Step 3
XE195 / XE295 Elliptical
12
Step 4
#87. 3.5x12mm
Sheet Metal Screw (18pcs)
#105.M5 x 15mm
Phillips Head Screw (19pcs)
Tools
#108. Phillips Head Screw Driver (1 pc) #107. Short Phillips Head Screw Driver (1 pc)
#109. 12m/m Wrench (1pc)
#106. 13/14m/m Wrench (1pc)
XE195 / XE295 Elliptical
13
STEP 1: CONSOLE MAST ASSEMBLY
•
Locate the Console Mast (12) and Console Mast Cover (41) and slide the Cover onto the
mast as far as it will go. Make sure the Console Mast Cover is facing the correct way.
•
Unravel and straighten out the Computer Cable (31) and feed it into the bottom of the console
mast tube and out of the top opening.
•
Install the Console Mast into the receiving bracket in the top of the Main Frame. NOTE: there is
one bolt already installed in the receiving bracket that will engage with the slot at the bottom of
the Console Mast. This needs to be tightened at the end along with the three other console
mast bolts.
•
Put one 3/8" x 2T Split Washer (96) onto the 3/8" x 2-1/4" Long Hex Head Bolt (60), and the
two 3/8" x 23 Curved Washers (84) onto the two 3/8" x 3/4" Short Hex Head Bolts (103).
Install the Long Hex Head Bolt (60) through the left side of the receiving bracket into the
Console Mast.
Assembly Instructions XE295
XE195 / XE295 Elliptical
14
•
Using the 13/14mm Wrench, tighten the three bolts, and the fourth bolt which is pre-installed,
firmly. These bolts should be tightened as much as you possibly can.
•
There will be three electrical wire connectors at the top opening of the console mast, two 2 pin
connectors for hand pulse sensors (36), one 10 pin connector for main wire harness (31) and
one connector for resistance switch (124). Connect these to the mating connectors on the back
of the electronic Console (30). The connectors are keyed, you cannot plug them in the wrong
way so do not force them. The two, 2 pin connectors can be plugged into either connector on
the back of the console.
•
Storing the excess wire back into the Console Mast, carefully install the Console onto the
mounting plate of Console Mast and secure using the four M5 x 10m/m Phillips Head Screws.
Make sure the wires do not get pinched between the console and mounting plate.
STEP 2: HANDLE BAR ASSEMBLY
•
Install the two 17m/m Wave Washers (83) onto the Left and Right side of the Handle Bar axle.
•
Slide the Left (10) and Right (11) Handle Bars onto the appropriate side of the axle. The
handlebars have a small sticker on them indicating
L
(left) and
R
(right).
•
Put the two 5/16" x 23mm Flat Washers onto the two 5/16" x 15m/m Hex Head Bolts and install,
and tighten, in the threaded holes in the ends of the axle.
XE195 / XE295 Elliptical
15
STEP 3: CONNECTING ARM ASSEMBLY
Align the hole in the rod end of the left Connecting arm (8) with the hole in the bracket of the
left Handle Bar (10). The rod end should be on the inner side of the Handle Bar bracket. Make
sure the ty-wrap is removed from the rod end and the sleeve spacer (22) does not fall out
during assembly. Take one 5/16" x 1-1/4" Hex Head Bolt (104) and install it through the Handle
Bar bracket and the rod end. Install one 5/16" x 20 x 1.5T Flat Washer (80) and one 5/16" x
7mm Nylon Nut (71) on the 5/16" x 1-1/4" Hex Head Bolt (104) and tighten as tight as possible
using the two12m/m Wrenches provided. Repeat the procedure for the right side Pedal
Connecting Arm.
XE195 / XE295 Elliptical
16
STEP 4: PLASTICS ASSEMBLY
•
Install the Connecting Arm Covers (2 each 57 & 57-1 and 58 & 58-1) over the connection of
the rod end and Handle Bars with the M5 x 15mm Screws (87) and 3.5x10m/m Self Tapping
Screws (105) by using the Short Phillips Screw Driver.
•
Install the two Wheel Covers (52) using the four M5x15m/m Phillips Head Screws (105).
•
Locate the two Rear Stabilizer Covers (19,20) and two Middle Stabilizer Covers (19,20) for the
Rear Rail Assembly and install with four M5 x 15m/m Screws (105). Then install front stabilizer
cover (49) with two M5 x 15m/m Screws (105).
•
Install the Front Handle Bar Covers (54-1 left, 55-1 right) and Rear Handle Bar Cover (54 left,
55 right) over the Handle Bar axle connections with the six 3.5x10mm Self Tapping Screws
(87).
•
Install the front (122) and rear (121) console mast covers with three M5 x 15m/m Screws (105)
and two 3.5x12m/m Sheet Metal Screw (87).
XE195 / XE295 Elliptical
17
Adjustable foot pedals, and orthopedically correct footpads
Through research performed with a leading sports scientist and physical rehabilitation expert,
Spirit engineering has developed a breakthrough in pedal design. No other elliptical, at any price,
offers these unique features. The history of elliptical use over the past few years tells us that many
users suffer from numb toes while working out on elliptical trainers. Many other users complain of
ankle, Achilles tendon, knee and/or hip pain. While researching a solution to these common
problems Spirit engineers consulted Richard DeKok, P.T., M.T.C., of St. Bernards Industrial
Rehabilitation Center in Jonesboro Arkansas.
Together we identified the inherent problem in elliptical designs and developed solutions to solve
the problems. What we found is that when you use an elliptical you tend to push outward during
the power stroke and not just straight back. This causes stress on the outer part of the foot and
throws off the natural alignment of the joints. The second problem we found is that many people
tend to stay up on the ball of their foot during the elliptical motion. Our solutions were simple but
effective:
•
The first solution was to add a 2-degree inward angle to the footpads. This might sound
simple but what it does is puts the users joints back into a neutral alignment. This eases
the over stressing of the ankles, knees and hips.
•
The second solution was to make the foot pedal adjustable to the user’s style of pedaling
the elliptical. We achieved this by adding an adjustment that allows the angle of the foot
pad to be changed. There are three adjustments. The lowest one will set the footpads at
zero (0) degrees, or flat, at the bottom of the elliptical stroke. The second position sets the
footpad to five (5) degrees and the top position sets the footpads to ten (10) degrees. The
XE195 & XE295 have a spring release pull pin under the rear of the footpads.
•
Because every body is different, and there are as many styles to pedal an elliptical as there
are people, we found there is no one angle that fit every user. Some users would be up on
the balls of their feet, resulting in numb toes, so we decided to let the user adjust the back
of the foot pad upward to support the heel, taking the pressure off of the nerves in the balls
of the feet and the Achilles tendon. The result was no more numb toes. Some users are
uncomfortable at this angle so for them we designed in three different adjustable angles so
they could find one that feels best for them.
A great side benefit of the adjustable footpad angle is that you end up working different muscle
groups. At the highest angle you will work the quadriceps more. At the lowest angle you work the
hamstrings and gluteus harder. Not a bad perk!
Transportation
The
elliptical
is equipped with two transport wheels that are engaged when rear of XE Series
Elliptical is lifted.
Features
XE195 / XE295 Elliptical
18
Getting familiar with the control panel
■
XE195 & XE295
Console
Power up
The Elliptical is supplied with an external power supply. When power is connected to the Elliptical,
the console will automatically power up. If there is no input to the console for a period of time the
console will go to stand-by mode. In stand-by mode the console display will turn off. To turn the
console on press any key.
When initially powered on the console will perform an internal self test. During this time all the
lights will turn on. When the lights go off the dot matrix display will show a software version (i.e.:
VER 1.0) and the message window will display an odometer reading. The odometer reading
displays how many hours the elliptical has been used and how many virtual miles the elliptical has
gone. The display will look like this: ODO 123 MI 123 HRS.
The odometer will remain displayed for only a few seconds then the console will go to the start up
display. The dot matrix display will be scrolling through the different profiles of the programs and
the message window will be scrolling the start up message. You may now begin to use the
console.
Operation of Your Elliptical
XE195 / XE295 Elliptical
19
Console Operation
Safety lock
When the elliptical is powered on the resistance at the pedals will be set to the very highest
setting. This is a safety feature that makes sure that you have a stable platform to stand on and
the footpads won’t move suddenly while setting the console data. It also ensures that children
cannot operate the elliptical unsupervised and injure themselves by pedaling too fast.
You can turn this feature off and have the elliptical set to the lightest resistance at power-up by
entering the maintenance menu:
Press and hold down the Start, Stop and Enter keys. Keep holding the keys down for
about 5 seconds and the message window will display “ALTXXXX Engineering mode”
Press the enter key. Scroll down the menu to “Functions” and press the enter key. Scroll
down to “Safety” and press the enter key to toggle the setting to “OFF”. Press the stop key
twice to exit to the start-up display.
Quick Start
This is the quickest way to start a workout. After the console powers up you just press the Start
key to begin, this will initiate the Quick Start mode. In Quick Start the Time will count up from zero
and the workload may be adjusted manually by pressing the Up or Down buttons. The dot matrix
display will have only the bottom row lit at first. As you increase the work load more rows will light
indicating a harder workout. The elliptical will get harder to pedal as the rows increase.
Basic information
The
Message Window
will initially be displaying Speed information. Each time the Enter button is
pressed the next set of information will appear, four windows in all. In order: Speed in RPM and
MPH, Work Level and Watts. If the Enter button is pressed during the Level and Watts display the
Scan light will come on and the message window will show each set of data for four seconds then
switch to the next set of data in a continuous loop. Pressing the Enter button again will bring you
back to the beginning.
The Elliptical has a built in heart rate monitoring system. Simply grasping the hand pulse sensors
on the stationary handle bars, or wearing the heart rate transmitter, will start the
Heart Icon
blinking (this may take a few seconds). The Pulse Display Window will display your heart rate, or
Pulse, in beats per minute.
The
Stop/Reset
button actually has several functions. Pressing the Stop/Reset key once during a
program will
Pause
the program for 5 minutes. If you need to get a drink, answer the phone or
any of the many things that could interrupt your workout, this is a great feature. To resume your
workout during Pause just press the Start key. If the Stop/Reset button is pressed twice during a
workout the program will end and the console will return to the start up screen. If the Stop/Reset
key is held down for 3 seconds the console will perform a complete
Reset.
During data entry for a
program the Stop/Reset key performs a
Previous Screen
function. This allows you to go back
one step in the programming each time you press the Stop/Reset key.
The
Program Keys
are used to preview each program. When you first turn the console on you
may press each program key to preview what the program profile looks like. If you decide that you
want to try a program, press the corresponding program key and then press the Enter key to
select the program and enter into the data-setting mode.
XE195 / XE295 Elliptical
20
The program keys also act as a
Number Key Pad
when you are in the data-setting mode. Under
each program key is a number. If you are setting new data, such as Age, weight etc., you can use
these keys to enter the numbers quickly.
The E series consoles include a built-in fan to help keep you cool. To turn the fan on, flip the
switch on the right side of the console case.
Programming the console
Each of the programs can be customized with your personal information and changed to suit your
needs. Some of the information asked for is necessary to ensure the readouts are correct. You will
be asked for your
Age
and
Weight
. Entering your
Age
is necessary during the Heart Rate control
programs to ensure the correct settings are in the program for your Age. Otherwise the work
settings could be too high or low for you. Enter your
Weight
for calculating a more correct
Calorie
reading. Although we cannot provide an exact calorie count we do want to be as close as
possible.
A message about Calories
: Calorie readings on every piece of exercise equipment, whether it is
in a gym or at home, are not accurate and tend to vary widely. They are meant only as a guide to
monitor your progress from workout to workout. The only way to measure your calorie burn
accurately is in a clinical setting connected to a host of machines. This is because every person is
different and burns calories at a different rate. Some good news is that you will continue to burn
calories at an accelerated rate for at least an hour after you have finished exercising!
Entering/Changing Settings
When you enter a program, by pressing a program key, then enter key, you have the option of
entering your own personal settings. If you want to workout without entering new settings then just
press the Start key. This will bypass the programming of data and take you directly to the start of
your workout. If you want to change the personal settings then just follow the instructions in the
message window. If you start a program without changing the settings the default, or saved,
settings will be used.
NOTE: Age and Weight default settings will change when you enter a new number. So the last
Age and Weight entered will be saved as the new default settings. If you enter your Age and
Weight the first time you use the Elliptical you will not have to enter it every time you work out
unless either your Age or Weight changes or someone else enters a different Age and Weight.
Manual
The Manual program works as the name implies, manually. This means that you control the
workload yourself and not the computer. To start the Manual program follow the instructions below
or just press the Manual button then the Enter button and follow the directions in the message
window.
1. Press the
Manual
key then press the
Enter
key.
2. The message window will ask you to enter your
Age
. You may enter your Age, using the
Up and Down keys or the numeric key pad, then press the Enter key to accept the new
number and proceed on to the next screen.
XE195 / XE295 Elliptical
21
3. You are now asked to enter your
Weight
. You may adjust the Weight number using the Up
and Down keys or the numeric key pad, then press enter to continue.
4. Next is
Time
. You may adjust the Time and press enter to continue.
5. Now you are finished editing the settings and can begin your workout by pressing the Start
key. You can also go back and modify your settings by pressing the Enter key. NOTE: At
any time during the editing of Data you can press the Stop key to go back one level, or
screen.
6. Once the program starts you will be at level one. This is the easiest level and it is a good
idea to stay at level one for a while to warm up. If you want to increase the work load at any
time press the Up key; the Down key will decrease the work load.
7. During the Manual program you will be able to scroll through the data in the message
window by pressing the
Enter key.
8. When the program ends you may press Start to begin the same program again or Stop to
exit the program or you can save the program you just completed as a
custom user
program
by pressing a User key and following the instructions in the message window.
Preset Programs
The Elliptical has five different programs that have been designed for a variety of workouts. These
five programs have factory preset profiles for achieving different goals. The initial built-in level of
difficulty for each program is set to a relatively easy level. You may adjust the level of difficulty for
each program before beginning by following the instructions in the message window after
selecting your program.
The Programs
HILL
The
Hill
program simulates going up and down a hill. The resistance in the pedals will steadily
increase and then decrease during the program.
Work Profile
XE195 / XE295 Elliptical
22
FATBURN
The
Fat Burn
program is designed, as the name implies, to maximize the burning of fat. There
are many schools of thought on the best way to burn fat but most experts agree that a lower
exertion level that stays at a steady workload is the best. The absolute best way to burn fat is to
keep your heart rate at around 60% to 70% of its maximum potential. This program does not use
heart rate but simulates a lower, steady exertion workout.
Work Profile
Cardio
The
Cardio
program is designed to increase your Cardio vascular function. This is exercise for
your heart and lungs. It will build up your heart muscle and increase blood flow and lung capacity.
This is achieved by incorporating a higher level of exertion with slight fluctuations in work.
Work Profile
Strength
The
Strength
program is designed to increase muscular strength in your lower body. This
program will steadily increase in resistance to a high level and then keeps you there. This is
designed to strengthen and tone your legs and glutes.
Work Profile
XE195 / XE295 Elliptical
24
Custom User Defined Programs
There are two customizable
User
programs that allow you to build and save your own workout.
The two programs,
User 1
and
User 2
, operate exactly the same way so there is no reason to
describe them separately. You can build your own custom program by following the instructions
below or you can save any other preset program you complete as a custom program. Both
programs allow you to further personalize it by adding your name.
1. Press the
User 1 or User 2
key. The message window will show a welcome message. If you
had previously saved a program the message will contain your name. Then press the
Enter
key to begin programming.
2. When you press enter, the message window will show “Name – A”, if there is no name saved.
If the name “David” had been previously saved the message window will show “Name –
David” and the D will be blinking. If there is a name saved you can change it or you may
press the Stop key to keep the name and continue to the next step. If you want to enter a
name use the Up and/or the Down key to change the first letter then press Enter to save the
first letter and continue to the next letter. When you have finished entering the name press
the Stop key to save the name and continue to the next step.
3. The message window will ask you to enter your
Age
. You may enter your Age, using the Up
and Down keys or the numeric key pad, then press the Enter key to accept the new number
and proceed on to the next screen.
4. You are now asked to enter your
Weight
. You may adjust the Weight number using the Up
and Down keys or the numeric key pad, then press enter to continue.
5. Next is
Time
. You may adjust the Time and press enter to continue.
6. Now you are asked to adjust the
Max Level.
This is the peak exertion level you will
experience during the program. The factory setting is level seven. Adjust the level and then
press enter.
7. Now the first column will be blinking and you are asked to adjust the level for the first
segment of the workout. When you finish adjusting the first segment, or if you don’t want to
change, then press enter to continue to the next segment.
8. The next segment will show the same level as the previously adjusted segment. Repeat the
same process as the last segment then press enter. Continue this process until all twenty
segments have been set.
9. The message window will then tell you to press enter to save the program. After saving the
program the message window says “New program saved” then will give you the option to
Start or modify the program. Pressing Stop will exit to the start up screen.
10. If you want to increase or decrease the workload at any time during the program press the Up
or Down key. This will only affect the workload for the present position in the profile. When the
profile changes to the next column it will return to the preset work level.
11. During the User 1 or User 2 program you will be able to scroll through the data in the
message window by pressing the
Enter key.
XE195 / XE295 Elliptical
26
Rate of Perceived Exertion
Heart rate is important but listening to your body also has a lot of advantages. There are more
variables involved in how hard you should workout than just heart rate. Your stress level, physical
health, emotional health, temperature, humidity, the time of day, the last time you ate and what
you ate, all contribute to the intensity at which you should workout. If you listen to your body, it will
tell you all of these things.
The rate of perceived exertion (RPE), also know as the Borg scale, was developed by Swedish
physiologist G.A.V. Borg. This scale rates exercise intensity from 6 to 20 depending upon how you
feel or the perception of your effort.
The scale is as follows:
Rating Perception of Effort
6 Minimal
7 Very,very light
8 Very,very light +
9 Very light
10 Very light +
11 Fairly light
12 Comfortable
13 Somewhat hard
14 Somewhat hard +
15 Hard
16 Hard +
17 Very hard
18 Very hard +
19 Very,very hard
20 Maximal
You can get an approximate heart rate level for each rating by simply adding a zero to each rating.
For example a rating of 12 will result in an approximate heart rate of 120 beats per minute. Your
RPE will vary depending up the factors discussed earlier. That is the major benefit of this type of
training. If your body is strong and rested, you will feel strong and your pace will feel easier. When
your body is in this condition, you are able to train harder and the RPE will support this. If you are
feeling tired and sluggish, it is because your body needs a break. In this condition, your pace will
feel harder. Again, this will show up in your RPE and you will train at the proper level for that day.
XE195 / XE295 Elliptical
27
How to wear your wireless chest strap transmitter:
1. Attach the transmitter to the elastic strap using the locking parts.
2. Adjust the strap as tightly as possible as long as the strap is not too tight to remain comfortable.
3. Position the transmitter with the POLAR logo centered in the middle of your body facing away
from your chest (some people must position the transmitter slightly left of center). Attach the
final end of the elastic strap by inserting the round end and, using the locking parts, secure the
transmitter and strap around your chest.
4. Position the transmitter immediately below the pectoral muscles.
5. Sweat is the best conductor to measure very minute heart beat electrical signals. However,
plain water can also be used to pre-wet the electrodes (2 black square areas on the reverse
side of the belt and either side of transmitter). It’s also recommended that you wear the
transmitter strap a few minutes before your work out. Some users, because of body chemistry,
have a more difficult time in achieving a strong, steady signal at the beginning. After “warming
up”, this problem lessens. As noted, wearing clothing over the transmitter/strap doesn’t affect
performance.
6. Your workout must be within range - distance between transmitter/receiver – to achieve a
strong steady signal. The length of range may vary somewhat but generally stay close enough
to the console to maintain good, strong, reliable readings. Wearing the transmitter immediately
against bare skin assures you of proper operation. If you wish, you may wear the transmitter
over a shirt. To do so, moisten the areas of the shirt that the electrodes will rest upon.
Erratic Operation:
Caution! Do not use this elliptical for Heart Rate Control unless a steady, solid Actual Heart
Rate value is being displayed. High, wild, random numbers being displayed indicate a
problem.
Areas to look for interference which may cause erratic heart rate:
(1) Microwave ovens, TV’s, small appliances, etc.
(2) Fluorescent lights.
(3) Some household security systems.
(4) Perimeter fence for a pet.
(5) Some people have problems with the transmitter picking up a signal from their skin. If you
have problems try wearing the transmitter upside down. Normally the transmitter will be oriented
so the POLAR logo is right side up.
(6) The antenna that picks up your heart rate is very sensitive. If there is an outside noise source,
turning the whole Elliptical machine 90 degrees may de-tune the interference.
(7) If you continue to experience problems contact your dealer
.
Using a Heart Rate Transmitter
XE195 / XE295 Elliptical
28
Heart Rate Control Program 1 & 2 (HR 1, HR 2) operation
Both programs operate the same, the only difference is that HR 1 is set to 60% and HR 2 is set to
80% of maximum heart rate. They both are programmed the same way.
To start the
HR 1 or HR 2
programs follow the instructions below or just press the HR 1 or HR 2
button then the Enter button and follow the directions in the message window.
1. Press the
HR 1 or HR 2
key then press the
Enter
key.
2. The message window will ask you to enter your
Age
. You may enter your Age, using the Up
and Down keys or the numeric key pad, then press the Enter key to accept the new number
and proceed on to the next screen.
3. You are now asked to enter your
Weight
. You may adjust the Weight number using the Up
and Down keys or the numeric key pad, then press enter to continue.
4. Next is
Time
. You may adjust the Time and press enter to continue.
5. Now you are asked to adjust the
Heart rate Level.
This is the heart rate level you will
experience during the program. Adjust the level and then press enter.
6. Now you are finished editing the settings and can begin your workout by pressing the Start
key. You can also go back and modify your settings by pressing the Enter key. NOTE: At any
time during the editing of Data you can press the Stop key to go back one level, or screen.
7. If you want to increase or decrease the workload at any time during the program press the Up
or Down key. This will allow you to change your target heart rate at any time during the
program.
8. During the HR 1 or HR 2 programs you will be able to scroll through the data in the message
window by pressing the
Enter key.
18. When the program ends you may press Start to begin the same program again or Stop to exit
the program or you can save the program you just completed as a
custom user program
by
pressing a User key and following the instructions in the message window.
XE195 / XE295 Elliptical
29
Maintenance:
1. Wipe down all areas in the sweat path with a damp cloth after each workout.
2. If a squeak, thump, clicking or rough feeling develops the main cause is most likely one of two
reasons:
i. The hardware was not sufficiently tightened during assembly. All bolts that were
installed during assembly need to be tightened as much as possible. It may be
necessary to use a larger wrench than the one provided if you cannot tighten the
bolts sufficiently. I cannot stress this point enough; 90% of calls to the service
department for noise issues can be traced to loose hardware or the rear rails being
dirty.
ii. Dirt build-up on the rear rails and polyurethane wheels are also a source of noise.
Noise from build-up on the rails can cause a thumping sound that you would swear
is coming from inside the main body of the machine because noise travels, and is
amplified, in the tubing of the frame. Clean the rails and wheels with a lint free cloth
and rubbing alcohol. Stubborn build-up can be removed with your thumbnail or a
non-metallic scraper, like the back edge of a plastic knife. After cleaning, apply a
small amount of lubricant on the rails with your fingers or a lint free cloth. You only
need a thin coat of lubrication, wipe off any excess.
3. If squeaks or other noises persist, check that the unit is properly leveled. There are 4 leveling
pads on the bottom of the rear rails, use a 14mm wrench (or adjustable wrench) to adjust the
levelers.
Maintenance Menu in console software:
The console has built in maintenance/diagnostic software. The software will allow you to change
the console settings from English to Metric and turn off the beeping of the speaker when a key is
pressed for example. To enter the Maintenance menu (may be called Engineering mode,
depending on version) press and hold down the Start, Stop and Enter keys. Keep holding the keys
down for about 5 seconds and the message window will display “ALTXXXX Engineering mode”.
Press the enter button to access the menu below:
a.
Key test
(will allow you to test all the keys to make sure they are functioning)
b.
Display test (
tests all the display functions)
c.
Functions
(Press enter to access settings)
i.
Sleep mode
(Turn on to have the console power down automatically after
20 minutes of inactivity)
ii.
Safety
(On = workload set to level 20 on power-up)
iii.
Motor test
(Press enter to run the workload motor up and down in a
continuous loop. Display shows level setting and position sensor reading.
Press stop to end test.)
iv.
Beep
(Turn on or off the beep when a key is pressed)
v.
Units
(Set to English or Metric display readings)
vi.
ODO reset
(reset the odometer)
vii.
Pause Mode
(Turn on allow 5 minutes of pause, turn off to have the
console pause indefinitely)
d. Security
(Allows you to lock the keypad so no unauthorized use is allowed)
e.
Factory settings
(Access only allowed by manufacturing)
f.
Exit
XE195 / XE295 Elliptical
30
Effective July 15, 2009
ELLIPTICAL WARRANTY
Spirit Manufacturing Inc. warrants all its home use treadmills’ parts for a period of time listed below, from the date of retail sale, as determined by sale receipt,
or
in the absence of a sales receipt eighteen (18) months from the original factory shipping date. Spirit’s responsibilities include providing new or
remanufactured parts, at Spirit’s option, and technical support to our independent dealers and servicing organizations. In the absence of a dealer or service
organization, these warranties will be administered by Spirit directly to a consumer. The warranty period applies to the following components:
Home Use WARRANTY
Frame and Brake Lifetime
Deck Lifetime
All Other Components 10 Years (5 years for XE195)
Labor 1 Year
NORMAL RESPONSIBILITIES OF THE CONSUMER
This warranty applies only to products in ordinary household use or, in the case of the XT685, light Institutional facility. The consumer is responsible for the
items listed below:
1. The warranty registration card must be completed and returned to the address listed on the card within 10 days of the original purchase to validate the
manufacturer’s limited warranty or register online at www.spiritfitness.com/warranty.asp
2. Proper use of the treadmill in accordance with the instructions provided in this manual, including maintenance and belt tracking.
3. Proper installation by an authorized Spirit service company in accordance with instructions provided with the treadmill and with all local electric codes.
4. Proper connection to a grounded power supply of sufficient voltage, replacement of blown fuses, repair of loose connections or defects in house/facility
wiring.
5. Expenses for making the treadmill accessible for servicing, including any item that was not part of the treadmill at the time it was shipped from the factory.
6. Damages to the treadmill finish during shipping, installation or following installation.
EXCLUSIONS
This warranty does not cover the following:
1. CONSEQUENTIAL, COLLATERAL, OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES
RESULTING FROM ANY BREACH OF THIS WRITTEN OR ANY IMPLIED WARRANTY.
Note: Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation or
exclusion may not apply to you.
2. Service call reimbursement to the consumer. Service call reimbursement to the dealer that does not involve malfunction or
defects in workmanship or material, for units that are beyond the warranty period, for units that are beyond the service call
reimbursement period, for treadmills not requiring component replacement, or treadmills not in ordinary household use.
3. Damages caused by services performed by persons other than authorized Spirit service companies; use of parts other than original
Spirit parts, or external causes such as alterations, modifications, abuse, misuse, accident, improper maintenance, inadequate power supply, or acts of God.
4. Products with original serial numbers that have been removed or altered.
5. Products that have been sold, transferred, bartered, or given to a third party.
6. Products that do not have a warranty registration card on file at Spirit Mfg. Spirit reserves the right to request proof of
purchase if no warranty record exists for the product.
7. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE.
SERVICE
Keep your bill of sale. Twelve (12) months from the date on the bill of sale or eighteen (18) months from the date of factory
shipping as determined by the serial number establishes the warranty period should service be required. If service is performed,
it is in your best interest to obtain and keep all receipts. This written warranty gives you specific legal rights. You may also have
other rights that vary from state to state. Service under this warranty must be obtained by following these steps, in order:
1. Contact your selling authorized Spirit dealer. OR
2. Contact your local authorized Spirit service organization.
3. If there is a question as to where to obtain service, contact our service department at (870) 935-1107.
4. If no local service is available, Spirit will repair or replace the parts, at Spirit’s option, within the warranty period at no charge
for parts. All transportation costs, both to our factory and upon return to the owner, are the responsibility of the owner. The
owner is responsible for adequate packaging upon return to Spirit. Spirit is not responsible for damages in shipping. Make all
freight damage claims with the appropriate freight carrier. DO NOT SHIP ANY UNIT TO OUR FACTORY WITHOUT A RETURN
AUTHORIZATION NUMBER. All units arriving without a return authorization number will be refused.
5. For any further information, or to contact our service department by mail, send your correspondence to:
Spirit Manufacturing, Inc.
P.O. Box 2037
Jonesboro, AR 72402-2037
Product features or specifications as described or illustrated are subject to change without notice. All warranties are made by
Spirit Manufacturing, Inc. This warranty applies only in the 50 states of the U.S.A..
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Spirit XE295 2009 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Spirit XE295 2009 in the language / languages: English as an attachment in your email.
The manual is 1,61 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.