584176
10
Zoom out
Zoom in
Previous page
1/45
Next page
XE100 / XE200 / XE300 Elliptical
9
UNPACKING THE UNIT
1. Using a razor knife (Box Cutter) cut the outside, bottom, edge of box along the dotted Line. Lift
Box over the unit and unpack.
2. Carefully remove all parts from carton and inspect for any damage or missing parts. If damaged
parts are found, or parts are missing, contact your dealer immediately.
3. Locate the hardware package. The hardware is separated into steps. Remove the tools first.
Remove the hardware for each step as needed to avoid confusion.
STEP 1: CONSOLE MAST ASSEMBLY
1.
Locate the Console Mast (12) and Console Mast Cover (41) and slide the Cover onto the
Mast as far as it will go. Make sure the Console Mast Cover is facing the correct way.
2. At the top opening of the Main Frame of the elliptical is a Computer Cable. Unravel and
straighten out the Computer Cable (31) and feed it into the bottom of the console mast tube
and out of the top opening.
3. Install the Console Mast into the receiving bracket in the top of the Main Frame. NOTE: there
is one bolt already installed in the receiving bracket that will engage with the slot at the bottom
of the Console Mast. This needs to be tightened at the end along with the three other console
mast bolts.
4. Put one 3/8" x 2T Split Washer (96) onto the 3/8" x 2-1/4" Long Hex Head Bolt (60), and the
two 3/8
"
x 23 Curved Washers (84) onto the two 3/8" x 3/4" Short Hex Head Bolts (103).
Install, and hand tighten, the Long Hex Head Bolt through the left side of the receiving bracket
into the Console Mast.
NOTE:
There is an electrical wire running through the Console Mast Tube. Be careful not to
damage or pinch this Computer Cable during this procedure. Damage to the Console could
result. Install, and hand tighten, the two Short Hex Head bolts through the front of the
receiving bracket into the Console Mast.
5. Using the 13/14m/m Wrench tighten the three bolts and the fourth bolt, which is pre-installed,
firmly. These bolts should be tightened as much as you possibly can.
6. There will be three electrical wire connectors at the top opening of the console mast, two 2 pin
connectors (hand pulse sensors)(36) and one 10 pin connector (main wire harness)(31).
Connect these to the mating connectors on the back of the electronic Console (30). The
connectors are keyed, you cannot plug them in the wrong way so do not force them. The two,
2 pin connectors can be plugged into either connector on the back of the console.
7. Storing the excess wire back into the Console Mast, carefully install the Console onto the
mounting plate of Console Mast and secure using the four M5 x 10m/m Phillips Head Screws.
Make sure the wires do not get pinched between the console and mounting plate.
Assembly Instructions( XE100 / XE200)
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Spirit XE200 2007 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Spirit XE200 2007 in the language / languages: English as an attachment in your email.

The manual is 2,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info