584044
12
Zoom out
Zoom in
Previous page
1/34
Next page
XBR95 & XBU75
11
STEP 4: RELEASE LEVER ASSEMBLY
1. Remove the M6 Button Head Socket Screw holding the clamp of the seat adjustment Release
Lever (40) by using the Allen Wrench (115). Install the Release Lever (40) onto the Handle Bar (6)
just behind the hand pulse sensors. Install the lever at an angle that allows easy access for use,
then install and tighten the socket screw removed earlier.
2. Install the Gas Cylinder (57) into the bracket of the Seat Back Frame (5) with one 5/16 x1-3/4
Hex Head Bolt (70), one 5/16 x 19 x 1.5T Flat Washer (76), 1pc of 5/16x 6T Nylon Nut (91) by
using the 13/14mm Wrench (130) and 13/15mm Wrench (113). Tighten the bolt until snug, but do
not over tighten to the point of binding.
3. Secure the Seat Recline Release Cable (58) and Seat Fore/Aft Release Cables (59) on the
Handle Bar (6) by using the four strips of Velcro Tape.
4. Install the Pedals (116 L, 117 R) in the Cranks by using the 13/15mm Wrench (113). Remember
that the left pedal has a reverse thread and will be screwed into the crank in the opposite rotation
from normal threads. There is an  stamped into the end of the threaded post of the left pedal
and an  in the right. Make sure to tighten the pedals as much as you possibly can. It may be
necessary to re-tighten the pedals if you feel a thumping during pedaling the bike. A clicking noise,
or thumping, sound during pedaling is usually caused by the pedals being too loose.
5. Install the Upper Computer Cable (44) and Hand pulse Wire Harness (133) into the connector in
the back of the Console (19). Install the console onto the mounting plate with the four M5x12mm
Phillips Head Screws (99) by using the Phillips Head Screw Driver (114).
6. Put on the Beverage Holders (R38&L39) onto left of the Handle Bar Seat (6) with the four 4x16
m/m Self Tapping Screws (105).
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Spirit XBR95 2007 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Spirit XBR95 2007 in the language / languages: English as an attachment in your email.

The manual is 1,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info