583985
22
Zoom out
Zoom in
Previous page
1/27
Next page
ET6 / ET8 / ET10
21
Belt and Bed - Your treadmill uses a very high-efficient low-friction bed. Performance is
maximized when the bed is kept as clean as possible. Use a soft, damp cloth or paper towel to
wipe the edge of the belt and the area between the belt edge and frame. Also reach as far as
practical directly under the belt edge. This should be done once a month to extend belt and bed life.
Use water only - no cleaners or abrasives. A mild soap and water solution along with a nylon scrub
brush will clean the top of the textured belt. Allow to dry before using.
Belt Dust - This occurs during normal break-in or until the belt stabilizes. Wiping excess off with a
damp cloth will minimize buildup.
General Cleaning - Dirt, dust, and pet hair can block air inlets and accumulate on the running belt.
On a monthly basis, vacuum underneath your treadmill to prevent the buildup of dirt that can be
sucked into the motor area while the treadmill is running. Once a year, you should remove the
black motor hood and vacuum out dirt that may accumulate. UNPLUG POWER CORD BEFORE
THIS TASK.
BELT ADJUSTMENTS:
Tread-belt Tension Adjustment - Belt tension is not critical for most users. It is very important for
joggers and runners in order to provide a smooth, steady running surface. Adjustment must be
made from the right side of the rear roller in order to adjust tension with the 6 mm Allen wrench
provided in the parts package. The adjustment bolt is located at the end of the right side rail as
noted in diagram below.
Tighten the rear roller only enough to prevent slippage at the front roller. Turn the tread-belt
tension adjusting bolt in increments of 1/4 turn and inspect for proper tension.
When an adjustment is made to the belt tension, you must also make a tracking
adjustment to compensate for the change in belt tension. This is accomplished by turning both
the tension and tracking Allen bolts an equal amount. This adjustment should be made by turning
both bolts clockwise by no more than a 1/4 turn at a time.
DO NOT OVERTIGHTEN Over tightening will cause belt damage and premature bearing failure.
General Maintenance
Note:
Adjustment is through small hole in end
cap.
Tracking / Tension
Adjustment
Tracking / Tension
Adjustment
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Spirit ET6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Spirit ET6 in the language / languages: English as an attachment in your email.

The manual is 0,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info