584039
17
Zoom out
Zoom in
Previous page
1/20
Next page
ET288/ET388
16
TREADBELT TRACKING ADJUSTMENT:
The performance of your treadmill is dependent on the frame running on a reasonably level
surface. If the frame is not level, the front and back roller cannot run parallel, and constant belt
adjustment may be necessary.
The treadmill is designed to keep the tread-belt reasonably centered while in use. It is normal for
some belts to drift near one side while the belt is running with no one on it. After a few minutes of
use, the tread-belt should have a tendency to center itself. If, during use, the belt continues to
move towar
d one side, adjustments are necessary.
TO SET TREADBELT TRACKING:
A 6 mm Allen wrench is provided to adjust the rear roller. Make tracking adjustments from the
left side only. Set belt speed at
approximately 2 to 3 mph. A small
adjustment can make a dramatic difference.
Turn the bolt only a 1/4 turn and wait a few
minutes for the belt to adjust itself. Continue
to make 1/4 rotation turns until the belt
stabilizes in the center of the running deck.
The belt may require periodic tracking
adjustment depending on use and
walking/running characteristics. Some users
will affect tracking differently. Expect to make
adjustments
as required to center the tread-belt. Adjustments will become less of a maintenance
concern as the belt is used. Proper belt tracking is an owner responsibility common with all
treadmills.
ATTENTION:
DAMAGE TO THE RUNNING BELT RESULTING FROM IMPROPER TRACKING /
TENSION ADJUSTMENTS IS NOT COVERED UNDER THE SPIRIT WARRANTY.
MAINTENANCE MODE:
If you want to set the Speed and Distance to Metric or if there is a problem with the speed and
you would like to perform the calibration procedure, use the Maintenance Mode. To enter
Maintenance Mode press, and hold for 5 seconds, the Start and Fast keys while installing the
safety k
ey.
The large display window will now be showing the Roller size. Roller size is used for the
calibration process and should be set to 2.36
The large display window will also display the setting for M (miles) or K (Kilometers).
Press the Enter key to change between M and K.
To run the calibration procedure, press the Start key.
o The display will show a number for the lowest speed setting (for miles the number
should be 0.5). Adjust the low speed setting with the Fast/Slow keys.
Using the
DOWN button, run the incline all the way down and press START.
o The display will show a number for the top speed setting (for Miles it should be
10.0). Adjust the top speed setting if needed. Using the UP button, run the incline
all the way up and press Start to begin calibration.
o The belt will start automatically and will adjust speeds between low and high. Be
careful because the belt will change speeds without warning. When the calibration
is finished the display will return to the start-up screen.
Using the DOWN button, run
the incline all the way down. Now you are ready to begin your workout.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Spirit ET388 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Spirit ET388 in the language / languages: English as an attachment in your email.

The manual is 0,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info