584040
14
Zoom out
Zoom in
Previous page
1/17
Next page
ET188
13
TREADBELT TRACKING ADJUSTMENT:
The performance of your treadmill is dependent on the frame running on a reasonably level
surface. If the frame is not level, the front and back roller cannot run parallel, and constant belt
adjustment may be necessary.
The treadmill is designed to keep the tread-belt reasonably centered while in use. It is normal
for some belts to drift near one side while the belt is running with no one on it. After a few
minutes of use, the tread-belt should have a tendency to center itself. If, during use, the belt
continues to move toward one side, adjustments are necessary.
TO SET TREADBELT TRACKING:
A 6 mm Allen wrench is provided to adjust the rear roller. Make tracking adjustments from the
left side only. Set belt speed at
approximately 2 to 3 mph. A small
adjustment can make a dramatic difference.
Turn the bolt only a 1/4 turn and wait a few
minutes for the belt to adjust itself.
Continue to make 1/4 rotation turns until
the belt stabilizes in the center of the
running deck. The belt may require
periodic tracking adjustment depending on
use and walking/running characteristics.
Some users will affect tracking differently.
Expect to make adjustments as required to center the tread-belt. Adjustments will become less
of a maintenance concern as the belt is used. Proper belt tracking is an owner responsibility
common with all treadmills.
ATTENTION:
DAMAGE TO THE RUNNING BELT RESULTING FROM IMPROPER TRACKING /
TENSION ADJUSTMENTS IS NOT COVERED UNDER THE SPIRIT WARRANTY.
MAINTENANCE MODE:
If you want to set the Speed and Distance to Metric or if there is a problem with the speed and
you would like to perform the calibration procedure, use the Maintenance Mode. To enter
Maintenance Mode press, and hold for 5 seconds, the Start, Stop and Mode keys while
installing the safety key.
The dot matrix display will now be showing the word SET
The Speed window will show a number for the roller size, press the up and/or Down key
to adjust the roller size. The roller size for the ET188 is 1.8
The Speed window will also display the setting for M (miles) or Km (Kilometers). Press
the Stop key to change between M and Km.
To run the calibration procedure, press the Start key.
o The display will show a number for the lowest speed setting (for miles the
number should be 0.5). Adjust the low speed setting and press Start.
o The display will show a number for the top speed setting (for Miles it should be
8.0). Adjust the top speed setting and press Start to begin calibration.
o The belt will start automatically and will adjust speeds between low and high. Be
careful because the belt will change speeds without warning. When the
calibration is finished the display will return to the start-up screen.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Spirit ET188 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Spirit ET188 in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info