583980
9
Zoom out
Zoom in
Previous page
1/26
Next page
EL555 Elliptical
8
UNPACKING THE UNIT
1. Using a razor knife (Box Cutter) cut the outside, bottom, edge of box along the dotted Line. Lift
Box over the unit and unpack.
2. Carefully remove all parts from carton and inspect for any damage or missing parts. If damaged
parts are found, or parts are missing, contact your dealer immediately.
3. Locate the hardware package. The hardware is separated into steps. Remove the tools first.
Remove the hardware for each step as needed to avoid confusion. The numbers in the instructions
that are in parenthesis (#) are the item number from the assembly drawing, for reference.
STEP 1: Incline Rail Assembly and Console Mast
1. Install the Incline Rail Assembly (2) into the U-channel bracket of the Main Frame (1). Secure
with the six bolts & associated hardware as follows: From the sides install two 3/8x1-1/2 Hex
Head Bolts (77) with two 3/8 Flat Washers (96) and two 3/8 Nuts (89). From the top install
four 5/16x2-1/4 Hex Head Bolts (167), four 5/16 Split Washers (178), four 5/16 Flat Washers
(100), and four 5/16 Star Washers (179), as shown in figure 1, and tighten securely.
2. Connect the three Incline Motor Power lines (your machine may have only one 3-pin power
connector) by matching the Red, White and Black color codes of the wires (37) and the 3-pin
position Sensor Connector (38).
3.
Locate the Console Mast (12) and Console Mast Cover (49) and slide the Cover onto the Mast
as far as it will go. Make sure the Console Mast Cover is facing the correct way. At the top
opening of the Main Frame of the elliptical
there
is a Computer Cable (39). Unravel and
straighten out the cables and feed them into the bottom of the console mast tube and out of the
top opening.
Install the Console Mast (12) into the receiving bracket on the top of the Main
Frame (1). Pull slightly on the cables at the top of the mast while installing. This will ensure the
cable does not get pinched and electrically shorted during the console mast assembly.
4.
Put one 3/8" x 2T Split Washer (128) onto the 3/8" x 2-1/4" Long Hex Head Bolt (75) and install
through the left side of the receiving bracket into the Console Mast (12). Put the two 3/8
"
x 23
Curved Washers (104) onto the two 3/8" x 3/4" Short Hex Head Bolts (76) and install through
the front of the console mast. Using the 13/14m/m Wrench, tighten the three bolts, and the
fourth bolt
, which
is pre-installed, firmly. These bolts should be tightened as much as you
possibly can.
5. Plug all of the connectors into the back of the console; Computer Cable (39), two Hand pulse
Cables (44) and Incline cable (36). Secure the Console (32) on the console mounting plate with
four M5x10m/m Phillips Head Screws (85).
Assembly Instructions
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Spirit EL555 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Spirit EL555 in the language / languages: English as an attachment in your email.

The manual is 1,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info