583976
9
Zoom out
Zoom in
Previous page
1/28
Next page
Assembly Instructions
UNPACKING THE UNIT
1. Using a razor knife (Box Cutter) cut the outside, bottom, edge of box along the dotted Line. Lift
Box over the unit and unpack.
2. Carefully remove all parts from carton and inspect for any damage or missing parts. If damaged
parts are found, or parts are missing, contact your dealer immediately.
3. Locate the hardware package. The hardware is separated into steps. Remove the tools first.
Remove the hardware for each step as needed to avoid confusion. The numbers in the instructions
that are in parenthesis (#) are the item number from the assembly drawing, for reference.
STEP 1: Incline Rail Assembly and Console Mast
1. Install the Incline Rail Assembly (2) into the U-channel bracket of the Main Frame (1). Secure
with the six bolts & associated hardware as follows: From the sides install two 3/8”x1-1/2” Hex
Head Bolts (77) with two 3/8”x19mm Flat Washers (96) and two 3/8”x7T Nylon Nuts (89). From
the top install four 5/16”x2-1/4” Hex Head Bolts (167), four 5/16” Split Washers (178), four
5/16”x20 Flat Washers (100), and four 5/16” Star Washers (179), as shown in figure 1, and
tighten with the 13/14 mm Wrench (124) and 12/14mm Wrench (129).
2. Connect the three Incline Motor Power lines by matching the Red, White and Black color codes
of the wires (37) and the 3-pin position Sensor Connector (38).
Locate the Console Mast (12)
and
Console Mast Cover (49)
and
slide the Cover
onto
the Mast as
far as
it
will
go. Make sure
the Console Mast Cover is
facing the correct way. At the
top opening
of
the Main
Frame
of
the
elliptical
there
is a Computer Cable (39) and an incline cable (36). Unravel
and straighten out the
cables and feed them
into the
bottom of the console mast tube and out of the top
opening.
Install the Console Mast (12) into the receiving bracket on the top of the Main Frame (1). Pull
slightly on the cables at the top of the mast while installing. This will ensure the cable does not
get pinched and electrically shorted during the console mast assembly.
3.
Put
one
3/8"
x
2T
Split
Washer (128)
onto the
3/8"
x
2-1/4" Long
Hex
Head Bolt (75) and install
through the left side of
the receiving
bracket
into
the
Console
Mast (12). Put the
two 3/8
"
x 23
Curved
Washers (104)
onto the
two 3/8" x 3/4" Short Hex Head Bolts (76) and install through
the front of the console mast. Using
the
13/14m/m
Wrench,
tighten
the
three
bolts,
and
the
fourth bolt
, which
is pre-installed, firmly. These
bolts should be tightened as
much as
you
possibly can.
4. Plug all of the connectors into the back of the console; Computer Cable (39), two Hand pulse
Cables (44) and Incline cable (36). Secure the Console (32) on the console mounting plate with
four M5x10m/m Phillips Head Screws (85).
EL7 Elliptical
8
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Spirit EL07 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Spirit EL07 in the language / languages: English as an attachment in your email.

The manual is 0,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info