Manual SpinMaster Cool Maker (page 2 of 20) (English)

683463

Zoom out

Zoom in

1/20

Check Out

For How-To

Videos!

@coolmaker

SEW N’ STYLE MACHINE

VISIT:

www.coolmaker.com

YEARS

IMPORTANT: Do not use fabrics other than those supplied or

recommended by the manufacturer for sewing.

For indoor dry locations use only. Clean the product with a dry cloth

only. Always use under adult supervision.

Do not store or use product near heat, sparks or ﬂame.

CAUTION: Use machine on a ﬂat surface.

CAUTION: Do not give the plush dolls or accessories that

are made by the Cool Maker™ Sew N’ Style Machine to

children under 3 years.

CAUTION: The fabric and stuﬃng materials provided may

cause suﬀocation.

CAUTION: This toy uses sharp needles (already assembled).

• Do not use if protective needle shroud is cracked or broken.

• NEVER use if any needles are bent or broken.

• In the unlikely event that a needle breaks during use, ensure that the

needle fragment is found and removed safely.

• Do not attempt to dismantle or rebuild the machine.

• Never open the main motor case of the machine.

• Do not submerge the unit or any other parts in water or use on wet

surfaces.

FCC STATEMENT:

This device complies with Part 15 of the FCC

rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2)

This device must accept any interference received, including

interference that may cause undesired operation. This

BATTERY INFORMATION

equipment has been tested and found to comply with the limits

for Class B digital devices pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection

against harmful interference to radio communications. This

equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with

the instruction, may cause harmful interference to radio

communication. However, there is no guarantee that

interference will not occur in a particular installation. If this toy

does cause interference to radio or television reception (you

can check this by turning the toy oﬀ and on while listening

for the interference), one or more of the following measures

may be useful: - Reorient or relocate the receiving antenna-

Increase the separation between the toy and the radio or the

TV- Consult the dealer or an experienced TV-radio technician

for help. NOTE: Changes, adjustments or modiﬁcations to this

unit, including but not limited to, replacement of any transmitter

component (crystal, semiconductor, etc) could result in a

violation of FCC rules under part 15 and/or 95 and must be

expressly approved by Spin Master Ltd or they could void the

user’s authority to operate the equipment.

CAN ICES3B)/NMB3B)

HOW TO INSTALL BATTERIES: Ensure machine is in

OFF position.

1. Open the battery door with a screwdriver.

2. If used batteries are present, remove these batteries from the unit

by pulling up on one end of each battery. DO NOT remove or install

batteries using sharp or metal tools.

3. Install new batteries as shown in the polarity diagram (+/-)

inside the battery compartment.

4. Replace battery door securely.

5. Check your local laws and regulations for correct recycling

and/or battery disposal.

BATTERY SAFETY INFORMATION: Batteries are small objects.

Replacement of batteries must be done by adults. Follow the

polarity (+/-) diagram in the battery compartment. Promptly

remove dead batteries from the toy. Dispose of used batteries

properly. Remove batteries for prolonged storage. Only

batteries of the same or equivalent type as recommended are

to be used. DO NOT incinerate used batteries. DO NOT dispose

of batteries in ﬁre, as batteries may explode or leak. DO NOT

mix old and new batteries or types of batteries (i.e. alkaline/

standard/rechargeable). Using rechargeable batteries is

not recommended due to possible reduced performance.

Rechargeable batteries are only to be charged under adult

supervision. Replaceable-rechargeable batteries are to be

removed from the toy before being charged. DO NOT recharge

non-rechargeable batteries. DO NOT short-circuit the supply

terminals. Requires 4 x AA 1.5 V (LR6) batteries (not included).

Batteries or battery packs must be recycled or disposed of

properly. When this product has reached the end of its useful

life it should not be disposed of with other household waste.

The Waste Electrical and Electronic Equipment Regulations

require it to be separately collected so that it can be treated

using the best available recovery and recycling techniques.

This will minimize the impact on the environment and human

health from soil and water contamination by any hazardous

substances, decrease the resources required to make new

products and avoid using up landﬁll space. Please do your part

by keeping this product out of the municipal waste stream!

The “wheelie bin” symbol means that it should be collected as

“waste electrical and electronic equipment”. You can return an

old product to your retailer when you buy a similar new one. For

other options, please contact your local council.

–

4 x AA batteries

Cover

BATTERY INFORMATION

1 Cool Maker™ Sew N’ Style Machine

2 Sheets of Glitter Fabric

2 Cool Maker™ Pre-cut Projects

1 Sheet of Cool Maker™ Felt Fabric

3 Cool Maker™ Decorative

Fabric Pieces

1 Page of Pop-out Patterns

1 Pom Pom Maker Attachment

1 Piece of Stretch Fabric

1 Bag of Stuﬃng

1 Elastic

1 Bundle of Ribbon

(3/8”x 50”/ 0.9 cm x 127 cm)

1 Bundle of Style String

(252” / 6.4 m)

2 Bundles of Pom Pom Yarn

(96” / 2.4 m Bundle)

1 Playbook

CONTENTS

Glitter Fabric

Felt Fabric

Pre-cut

Projects

Pom Pom Maker

Attachment

Decorative Fabric

Pieces

Stuﬃng

Pop-out

Patterns

Elastic

Stretch

Fabric

Pink

Ribbon

Blue Pom Pom Yarn

Pink Style

String

Diagram:

Manual Knob

Style String

Guide

Style String Guide

Seam Guide

Fold Guide

Pom Pom Maker

Attachment

ON/OFF Switch

Start/Stop Button

Storage Drawer

DIAGRAM

*Requires 4 AA

(LR6) Batteries

Not Included.

Needle Guard

Light

BASIC SEWING TIPS

@coolmaker

Basic Sewing Tips:

Follow these steps when

creating projects:

1. Turn ONOFF switch to ‘I’.

2. Press STARTSTOP button to

start the machine.

3. Make sure to slowly feed the

fabric under the needle guard and

follow the seam guides.

4. To stop sewing, press the STARTSTOP button. To

turn oﬀ the machine turn the OFF switch to ‘0’.

TIP

Have ruler,

scissors and

pencil handy

before starting

your project.

STYLE STRING SEWING TIPS

Style String

Sewing Tips:

For Glitter &

Stretch Fabric:

Turn ONOFF switch

to ‘I’.

1. Unravel an arm’s

length of style string

from the spool.

2. Thread style string through the guides on top

of the machine.

3. Guide the style string underneath the needle

guard.

4. To start sewing press the start button.

5. Follow step 3 and 4 from page 6.

6. Cut style string at seam edge.

CREATE A POM POM

Insert the pom pom attachment into

the machine.

Tie 8”/20 cm piece of yarn around

the wrapped prongs.

Use scissors to cut the looped ends.

Fluﬀ and trim. Do not cut the middle tie.

Wrap the remaining yarn

around both prongs.

Cut 8”/20 cm piece of pom pom yarn and

set aside to use in step 4.

Remove from the pom pom maker and

tie double knots with remaining yarn.

CREATE A POM POM

Create a

Pom Pom

Tie onto Glitter Pouch.

Tie onto Hair

Clip Holder.

TIP: For better results,

ask an adult to help tie a

tighter knot.

Check Out

@coolmaker

for How-To Videos!

PLUSH UNICORN

Scrunch one end of the glitter fabric. Place on top layer of felt and

sew with style string. Repeat with smaller piece of glitter fabric to

create layered skirt.

Using the two unicorn pop-out

patterns, trace and cut two

pieces of pink glitter fabric.

Remove style string, and sew the unicorn

front and back layers together. Notice the

symbols that show where to START (1), STOP

(2), and spot stitch (+) on the back panel.

Do not stitch over glitter fabric skirt.

Prepare the pieces you will need.

PLUSH UNICORN

Stuﬀ your character through the

bottom opening. DO NOT OVERSTUFF.

Stitch the stuﬀed character closed, from (2) to (1).

TIP: If the seam comes

apart, sew over the

stitching path again.

Plush

Unicorn

PROJECT

*Follow similar steps to

create butterﬂy plush.

Check Out

@coolmaker

for How-To Videos!

GLITTER POUCH

Prepare the pieces you will need.

Fold glitter fabric in half, top folded seams

facing up. Sew left and right seams, stopping

at the style string.

Fold short end of glitter fabric over 1” / 2.5 cm.

Using the fold guide, sew in place

with style string. Repeat for the other side.

Fold one end of the ribbon over the pom

pom prong. This will help guide the

ribbon through the top seam.

Cut two pieces of ribbon, double the

length of the pouch opening.

TIP: Have pom

pom attachment

handy before

starting this

project.

GLITTER POUCH

To create the drawstring closure, repeat steps 5-8 with the second ribbon,

starting on side without the knot.

To complete pouch,

ﬂip inside out.

Check Out

@coolmaker

for How-To Videos!

Tie the two ribbon ends together as

shown.

PROJECT

Glitter

Pouch

Insert the pom pom prong with ribbon into

either opening of the top seam. Push prong

through until the ribbon can be pulled out.

Using the same piece of ribbon repeat

step 6 on the opposite side of top seam.

TIP: Add a pom pom

(pg. 8-9)

HAIR CLIP HOLDER

Prepare the pieces you will need.

Thread style string and sew ribbon at the

top and bottom of the felt.

Cut two pieces of ribbon,

the length of the felt.

Following the paper pattern instructions,

spot stitch the glitter fabric to felt and

trim style string. Scrunch the long edge

of glitter fabric and sew from (1) to (2),

where indicated.

Pop out the two hair clip holder paper patterns. Trace the

shorter pattern onto felt, and cut. Using the longer pattern,

trace and cut two pieces of glitter fabric.

HAIR CLIP HOLDER

Hair Clip

Holder

PROJECT

TIP: Add a pom pom (pg. 8–9) and

a gathered bow for extra style!

To create handle, sew ribbon on

top left and right corners.

TIP:

Customize with

decorative pieces!

Check Out

@coolmaker

for How-To Videos!

SCRUNCHIE

Prepare the pieces you will need.

Cut a piece of style string 3” / 7.6 cm

longer than the pre-cut stretch fabric.

Thread the machine with style string and

sew rest of the seam.

Spot stitch the end of the style string to

the side seam.

Pull the long string until fabric

bunches and ﬂip inside out.

Fold the fabric lengthwise with the style

string inside along the fold.

PROJECT

Scrunchie

TROUBLESHOOTING

Push elastic through and tie the ends together.

Insert one end

of fabric into

the other end

and sew. Do not

sew through

elastic.

CAUTION:

Never use more than 2 layers of felt fabric at a time. Machine can jam.

PROBLEMS: SOLUTIONS:

Machine Goes On Stand By Mode Turn machine OFF/ON.

Flickering Lights 1. Batteries may be low and require changing.

2. Fabric may be jammed. See trouble shooting for Fabric Jams.

Loose Seams Stitch over weak spots once more to strengthen seam. The slower

you push the fabric through, the stronger the seam will be.

Fabric Jams 1. Turn machine OFF/ON - needles will reset to default position. OR

2. Turn machine OFF. Push in and turn the manual knob until the

needles are cleared of the fabric and Style String. Remove the

fabric and restart the machine.

this information, addresses and phone numbers for future reference. Content may

vary from pictures. An adult should periodically check this toy to ensure no damage or

hazards exist, if so, remove from use. Children should be supervised during play. Meets

CPSC Safety Requirements. Spin Master Ltd. reserves the right to discontinue use of the

www.coolmaker.com website at any time.

The YouTube logo and YouTube icon are trademarks of Google Inc. The Instagram Glyph

logo is a trademark of Instagram, LLC in the United States and elsewhere.

SPIN MASTER LTD., 450 FRONT STREET WEST, TORONTO, ON M5V 1B6 CANADA

Imported into EU by SPIN MASTER INTERNATIONAL, S.A.R.L., 20 RUE DES

PEUPLIERS, L-2328, LUXEMBOURG

MADE IN CHINA

(T56013_0003_20088604_GEN_IS_R2)

Be a Cool Maker™!

www.coolmaker.com

DETATCH FOR REFERENCE

a WARNING: CHOKING HAZARD – Small parts.

a WARNING: STRANGULATION HAZARD - Long cord.

DETATCH FOR REFERENCE

DIAGRAM

Diagram:

Manual Knob

Style String

Guide

Style String Guide

Seam Guide

Fold Guide

Pom Pom Maker

Attachment

ON/OFF Switch

Start/Stop Button

Storage Drawer

*Requires 4 AA

(LR6) Batteries

Not Included.

Needle Guard

Light

Sew it

with the SEW N’ STYLE MACHINE!

Shape it

with the POTTERY STUDIO!

Style it

with the AIRBRUSH STYLING STUDIO!

Each sold separately.

Be a

Cool Maker!

™

www.coolmaker.

@coolmaker

#coolmaker

Be a Cool Maker!™

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of SpinMaster Cool Maker in the language / languages: English as an attachment in your email.

The manual is 2,4 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

SpinMaster Cool Maker Manual

Product: