708059
20
Zoom out
Zoom in
Previous page
1/42
Next page
20

Electric RPM Sensor
The optional electric RPM sensor is designed to be used with any brushless
motor. The sensor has two leads to attach to any two of the three motor wires.
This is typically done by soldering.
Installation
To install the electric RPM sensor using servo tape, attach the sensor in
a convenient place that allows the leads to reach the motor wires and the
TM1000 telemetry unit.
Solder the two sensor wires to any two motor leads.
Plug the sensor lead into the RPM port on the TM1000 telemetry module.
Testing
Turn the transmitter and receiver on and scroll to the RPM telemetry screen.
Run the motor and the RPM should register on the screen.
The RED LED on the TM1000 indicates the sensor is picking up properly.
 It is necessary to program a matching pole count in the telemetry
RPM screen to have accurate reading on screen. The motor’s pole count is
normally in the motor manufacturer’s instructions or on the manufacturer’s
website.

The Frame Rate function allows the selection of 11ms or 22ms frame rate. When
a 11ms frame rate receiver is used, the transmitter defaults to 11ms frame rate.
This fast frame rate is not compatable with some types of analog servos and the
Frame Rate screen allows the selection of a 22ms frame rate when a high frame
rate receiver is being used with analog servos.

Press and hold the roller while turning on the the transmitter. When system setup
appears on screen relese the roller. The DX8 is now in System Setup mode.
Rotate the roller to highlight Frame Rate then press.
The following screen appears:
Rotate the roller to highlight the frame rate then press. Now rotate the roller to
select 11ms or 22 ms frame rate.

The DX8 features a programmable trainer function with three trainer modes. The
transmitter assigns the trainer function to the trainer button. The function activates
when the switch is depressed and one of the three trainer modes is selected. The
three trainer Modes include:

In Inhibit you can use the transmitter as a slave only. However, the slave
transmitter must have the same programming as the master (e.g., servo
reversing, travel adjust, sub-trim, trims).

With Programmable Master you can program the transmitter to transfer any or
all channels when you activate the trainer switch. This is ideal for beginners
so the student learns control of individual channels (aileron only for example)
while the trainer maintains control of all other channels.
Note: When Programmable Master is selected for the master transmitter,
all settings for the slave transmitter (i.e. Servo reversing, wing type, Sub
trim, Travel Adjust, Mixing, etc.) must match the master’s transmitter
programming. If two DX8’s are being used simply copy and transfer the
model memory using the SD card from the master’s model to the slave.
The slave transmitter is then programmed to inhibit in the trainer screen.

When Pilot Link Master is selected the slave transmitter has control of the
stick function only (aileron, elevator rudder and throttle) while the master
maintains control of all other channels and functions including D/R and
switch positions. This is ideal for complex models as the master maintains
control of all secondary functions and controls all other channels.

Use Slave mode when flying with the DX8 as a slave when the master
radio has activated its Pilot Link. In this case, there is no need to match
programming between the slave and master transmitter.

Use the System Setting screen to establish the overall transmitter setting that will
apply to ALL model memories. These settings include: User Name, Contrast,
Mode, Region and Language. If you select Mode One, then Mode One will be
selected for all 30 model memories. Note: Even when models are imported from
an SD card the system settings in the transmitter will remain.

Press and hold the roller while turning on the transmitter. When System Setup
appears on the screen, release the roller. The DX8 is now in System Setup Mode.
Highlight System Settings then press. The following screen appears:
Highlight the function you wish to change then press the roller to select.
User Name
User Name allows the identification of the owner to be programmed into the
transmitter. The user name appears during the startup process at the lower left
corner of the startup screen.
EN
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Spektrum DX8 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Spektrum DX8 in the language / languages: English as an attachment in your email.

The manual is 5,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Spektrum DX8

Spektrum DX8 Quick start guide - English - 100 pages

Spektrum DX8 User Manual - German - 42 pages

Spektrum DX8 User Manual - French - 42 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info