(S091600016, 42mm x 30mm x 7mm) into the left and right sides of the BB shell/axle (S150400007)
B
(fig.1).
Install the inner spacer (S150400008)
C
, bearings (S150600002)
D
and outer spacers (S150400006)
E
into the shell of the frame (fig.1).
Align the main pivot holes
F
of the chainstay assembly with the shell of the frame
G
, then slide the BB shell/axle through the drive-side chainstay
hole and the shell of the frame (fig.1).
Thread the axle into the non-drive-side chainstay hole, using the supplied main pivot lock tool
H
(fig.2).
I
3
4
With the main pivot lock tool (S150400002)
H
positioned with the lip facing out, tighten the bottom bracket by inserting a long 6mm Allen key or
a screwdriver shaft
I
into the holes in the lip and rotate counter-clockwise (fig.3). Once tension is felt, rotate the splined ring an additional 1/4-turn.
Fig.4: Once tight, flip the pivot lock tool around so that the lip is positioned over the lower corner of the chainstay and lock it in place by inserting
three screws into the ISCG tab holes (fig.4). If desired, install a chainguide/bashguard assembly before inserting the bolts.
NOTE: Certain chainguides might interfere with the lip portion of the pivot lock tool. In the case of interference, use the flat lock tool (S150400001).
Derailleur cable routing
1
A
B
C
E
2
D
Insert a full-length piece of derailleur cable housing, measuring at least 6’ (1800mm) long, starting at the rear derailleur port
A
(fig.1).
Guide the housing up the seatstay until it exits through the upper seatstay port
B
(fig.1). Make sure the seatstay protector (S159900014) is installed.
Insert the housing into the port below the shock link
C
(fig.1). Continue running the housing into the frame until it exits at the head tube port
D
(fig.2).
Trim the housing to the required length, install the cable and adjust the derailleur, all according to the manufacturer’s instructions.
Install the housing stop assembly (S156500003)
E
(fig.1). Tighten the bolt just enough so that the housing can’t move.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Specialized FSR - 2015 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Specialized FSR - 2015 in the language / languages: English as an attachment in your email.
The manual is 14,03 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
