Manual Speaka 629568 (page 3 of 8) (English, German, Dutch, French)

552582

Zoom out

Zoom in

1/8

O P E R A T I N G I N T R U C T I O N S

Version 08/14

Decor TV wall bracket 58-107 cm (23-42”)

tiltable and swivelling 25 kg

Beech Item no. 62 95 68

Oak Item no. 63 18 19

Mahogany Item no. 63 18 20

Intended use

The TV wall bracket is used to mount suitable TV sets on walls.

The TV set may not exceed the values for TV size and weight specied in the section “Technical

Data”.

Any use other than that described above will lead to the damage of this product or of the TV

set. Furthermore, this involves risks such as damage to furniture in close proximity to the wall

bracket, personal injury, etc.

No part of the product may be modied or altered.

The safety instructions must be observed at all times.

Package Contents

See page 2 in the enclosed mounting instructions.

Safety Instructions

The warranty will be void in the event of damage caused by failure to observe

these safety instructions. We do not assume any liability for any resulting dam-

age.

We shall not accept liability for damage to property or personal injury caused

by incorrect handling or non-compliance with the safety instructions. In such

cases, the warranty will be null and void.

The exclamation mark symbol indicates that important information is included

in these operating instructions.

The arrow symbol indicates tips and notes.

• A TV wall holder is not a toy. Keep the device out of the reach of children.

• Do not leave packaging material lying around carelessly. It may become a dangerous play-

thing for children.

• Selecting an unsuitable installation location can lead to personal or material damage.

• Proceed with care when assembling and installing the product. The product may have sharp

edges. There is a risk of injury!

• Carry out only the work on the TV wall holder that is necessary in order to install it (or to adjust

it). Never perform any conversion or repair work.

• Before beginning the installation process, check whether there is an appropriate mounting

option for a TV wall bracket on the back of your TV set.

• Depending on the size and design of the TV set and TV wall holder concerned, it is sensible for

a second person to help with the installation. This person can hold the TV set still, for example,

while you are attaching the TV set to the wall bracket.

• Apply your full concentration when carrying out the installation, because if the TV set and/or

TV wall holder were to fall, this could cause expensive damage to the equipment and there is

the potential danger of personal injury!

• Check all the screw ttings from time to time. Adjusting the position of the TV set and/or the

wall bracket and moving them can sometimes cause the screws to become loose over time.

• Do not apply force when moving/adjusting the TV set or the TV wall bracket. The TV set may

get damaged from it.

• When moving/adjusting, do not press on the TV set’s screen.

• Do not overload the TV wall bracket. Pay attention to the details provided by the manufacturer

for the maximum TV set weight and/or its size.

• Do not use the TV wall bracket to support yourself or to hold onto.

• Do not x any objects to the TV wall bracket other than the TV set for which it was intended.

• In case of doubt, do not perform the installation yourself. Have an expert carry out the instal-

lation.

O P E R A T I N G I N T R U C T I O N S

Installation

Wall-mounting is permissible only where the wall concerned is of the correct

type and condition. Lightweight partition walls or those made from gypsum

boards with unstable substructures are normally unsuitable. However, special-

ist retailers do sometimes stock special dowel ttings for such installation lo-

cations. If you are in doubt, ask a specialist before installation.

Depending on the base wall material (e.g. concrete), suitable mounting materi-

als must be used (screws, dowels, etc.). The dowel screws enclosed are only

suitable for solid walls. Special dowels and screws are not normally supplied

with the TV wall holder and must be bought separately, depending on the type

and condition of the wall concerned.

Due to the weight of the TV set, TV wall holder and the lever action involved,

ensure that the screws are xed securely.

Plan the installation location carefully, so that the TV wall holder with the TV

set xed to it will be situated at the correct location (height and position) when

you have nished the installation.

Pay attention when drilling and tightening the screws that no cable or pipes in

the wall are damaged. Inadvertently drilling through electric cables causes the

life-threatening danger of an electric shock!

Pay special attention to your safety when using electric tools (e.g. a drill). You

should also heed the safety notes in the corresponding instructions.

Make sure no persons are in the area under the TV wall holder and/or the TV set

during the installation.

For this process, please pay attention to the pictures in the enclosed installation

instructions.

Preparation of the TV set

• It is usually necessary to remove the TV set’s existing base before mounting it on a wall

bracket. Observe the operating instructions for your TV set.

• Put the TV set at on a soft and clean underlay, with the display side facing downwards. Do not

apply pressure on the display. Protect valuable furniture surfaces during installation by using

a suitable pad or cloth.

• Remove the existing base. Depending on the TV set, this base is either screwed in place or

clipped on.

Figure 1a (Installation with cavity wall structures):

• Select the position and the height of the wall bracket at the mounting location. The attachment

holes of the mounting plate must be centred over a wooden stud or another load-bearing as-

sembly element of the wall structure. To nd this position, something like a stud nder can be

helpful.

Make sure to mount the wall bracket the right way round. The arrow on the mounting

plate with the label UP must point upward.

• Use a spirit level to align the wall bracket horizontally.

• Mark the necessary drilling holes at the mounting site. To this end, use the wall bracket as a

template.

• Drill the required holes.

• Screw the wall bracket in place with three screws (W-A or screws suitable for the mounting

surface from the dealer) and washers (W-C).

The enclosed dowels (W-B) are not used in this type of installation.

Figure 1b (Installation with solid wall structures):

• Select the position and the height of the wall bracket at the mounting location.

Make sure to mount the wall bracket the right way round. The arrow on the mounting

plate with the label UP must point upward.

• Use a spirit level to align the wall bracket horizontally.

• Mark the necessary drilling holes at the mounting site. To this end, use the wall bracket as a

template.

• Drill the required holes and insert suitable dowels in the boreholes (W-B or special dowels).

• Screw the wall bracket into place with three screws (W-A or screws suitable for the mounting

surface from the dealer) and washers (W-C).

Figure 2:

• Place both covers on the mounting plate on the wall.

• In this process, the cover with the cable holder must be mounted underneath.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Speaka 629568 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,27 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Speaka 629568 Manual

Product: