744245
22
Zoom out
Zoom in
Previous page
1/53
Next page
GB 22
prevent overheating. This safety device must not be used as a water heater.
The thermal discharge safety device is not preassembled for safety reasons
during transport and installation, but instead enclosed in the combustion
chamber. During installation, it must be fitted to the marked connection.
Then, use the adapter to screw the capillary line to the TAS. This has been
tested and approved for a minimum throughput of 900 kg / h of water.
The following instructions must always be complied with for the installation,
so that the safety device can function:
At the cold water inlet, a flow pressure of at least 2 bar must be available.
This pressure must be constantly ensured. This is because, operation on
a mains-voltage-dependent domestic water supply is not permitted!
Minimum water throughput of approx. 900 L/h must be ensured. It must
not be possible to shut off this supply line!
It must be ensured that cold water (5-20°C) is available at any time.
Domestic water supplies is not included in this.
All safety-relevant components must be integrated in the system in such a
manner that function and leak-tightness can be checked at any time. The
discharge of the thermal discharge safety device must be designed in such a
manner that a check (e.g. via a drain with siphon) can take place at any time.
Before commissioning, the cold water pipe must be purged! This flushes out
dirt, which would otherwise impact closing of the TAS. The manufacturer's
instructions for the TAS must be observed.
2.3.7.4 THERMAL PUMP CONTROLLER
For optimum control of the circulating pump, a thermostat is integrated in the
lower compartment. This ensures that the circulating pump starts only with
adequate water temperature (> 60°C). The boiler control or similar devices
can be used as a controller if a switch-on temperature of the pump between
60°C and 68°C is guaranteed. The maximum contact load of the thermal
pump control at alternating current 250 V AC is approximately 10 (2.5) A.
The factory setting of the thermostat has been set to about 62°C. When
the switch-on and switch-off temperature of the circulation pump of return
riser is reached, or undershot, the required water temperature in the water
heat exchanger of the Senso M H2O / Piko H2O is determined. Optionally, if
conditions so require, the temperature can be adjusted by the installation
company. To do this, the housing cover of the pump thermostat, which is
located in the lower compartment of the stove, must be removed. After
removing the cover, the temperature range can be changed by adjusting
the red screw.
Please note: If water temperatures fall below 60°C, there is an increasing
risk of temperature falling below the dew point level! This can result in the
formation of shining soot. Furthermore, this shortens the cleaning interval.
We do not recommend that the switch-on temperature is set below 60°C,
but also not set at more than 68°C.
2.3.7.5 ELECTRICAL CONNECTION
The entire electrical installation of the individual components of the heating
system must only be executed by an authorised specialised company. All
electrical installations are to be carried out as per the VDE regulations (e.g.
VDE 0105, VDE 0116, VDE 0100, etc.) and the technical connection condi-
tions of the local power company.
On the Senso M H2O / Piko H2O, only carry out the electrical installation
from thermostats to the pump of the return flow temperature riser („2.3.7.7
Return flow temperature boost“ on page 25) and to domestic power grid
(see figure). The temperature-resistant connection line is about 3.0 m long
and already stuck to the thermostat.
The function of the thermostat switch is to be able to test the hot water (e.g.
from kettle) and the thermometer The cladding must be removed to do this.
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Spartherm Passo S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Spartherm Passo S in the language / languages: English as an attachment in your email.

The manual is 3.7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Spartherm Passo S

Spartherm Passo S User Manual - German - 52 pages

Spartherm Passo S User Manual - Dutch - 53 pages

Spartherm Passo S User Manual - Dutch - 44 pages

Spartherm Passo S User Manual - French - 57 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info