Manual Sparky HAG 2000ED (page 6 of 74) (English, German, French, Italian, Polish, Portuguese, Spanish)

583074

Zoom out

Zoom in

1/74

HAG 2000 • HAG 2000E • HAG 2000ED

WARNING: Do not place your hand over the

air vents (3) at the machine rear or block the vents in

any way.

▪ Stay alert, watch what you are doing and use common

sense when operating a appliance. Do not use a ap-

pliance while you are tired.

▪ Take a secure stance; do not overreach, especially on

ladders and stages.

▪ To use this appliance properly, you must observe

the safety regulations, the assembly and operating

instructions in this booklet. All persons who use and

service the machine have to be acquainted with this

Manual and must be informed about the potential haz-

ards when operating this appliance.

▪ This machine is not intended for use by persons (in-

cluding children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowl-

edge, unless they have been given supervision or in-

struction concerning use of the appliance by a person

responsible for their safety.

▪ Children should be supervised to ensure that they do

not play with the appliance.

▪ The manufacturer shall not be liable for any changes

made to the tool nor for any damage resulting from

such changes.

▪ The appliance must not be used outdoors in rainy

weather, or in moist environment (after rain) or in close

vicinity with easily flammable liquids and gases. The

working place should be well lit.

Know your product

Before using the appliance, familiarize yourself with all

the operating features and safety requirements.

Use the appliance and accessories only for the applica-

tions intended. All other applications are expressly ruled

out.

1. Nozzle

2. Heat protector

3. Ventilation slots

4. Rubber soft stand

5. Temperature control buttons (HAG 2000ED)

5a. Temperature regulator (HAG 2000E)

6. ON/OFF switch

7. LCD display (HAG 2000ED)

8. Reduction nozzle

9. Glass protection nozzle

10. Reector nozzle

11. Flat nozzle

12. Triangular scraper

Operation instructions

This appliance is supplied from single-phase alternat-

ing current mains only. It is double insulated according

to EN 60335-1 and can be connected to grounded or

not grounded sockets. This appliance is radio sup-

pressed in compliance with EN 55014-1, EN 55014-2,

EN 61000-3-2, EN 61000-3-3 for radio interference.

This appliance is intended for the removal of paint, form-

ing and welding of plastic, warming of heat-shrinkable

tubing; the tool is also suitable for soldering, loosening

adhesive joints and defrosting water pipes.

PRIOR TO INITIAL OPERATION

▪ Make sure the power supply voltage corresponds to

the value indicated on the name plate with technical

data of the tool.

▪ Always check the position of ON/OFF switch. The ap-

pliance must be connected to the power supply socket

only when this switch is in OFF position as the maxi-

mum temperature is achieved for 60 seconds only.

▪ Make sure that the cord and the plug are in order. If the

replacement of the supply cord is necessary, this has

to be done by the manufacturer or his agent in order

to avoid a safety hazard.

WARNING: Always switch off and unplug the

appliance prior to any adjustment or maintenance.

▪ Check the functioning of the tool before each use and, in

case of a defect, have it repaired immediately by a quali-

fied person; never attempt to open the tool yourself.

▪ The distance between the nozzle and the processed

material will vary depending on the kind of material

but regardless of the regulator position keep the air

outlet at least at 50 mm away from the processed

surface.

▪ All application examples (except removing paint from

windows) can be performed without accessories;

however, using the appropriate accessory facilitates

operation and significantly improves the quality of the

results.

SWITCHING ON - SWITCHING OFF

The hot air gun can be switched on and off by means of

the 3-stage ON/OFF switch (6) at the rear of the handle.

Switching on: Set the switch (6) to position I. Some

smoke may be emitted after switching on; this does not

indicate a problem.

Switching off: Set the switch (6) to position O. Let the

machine cool down with the nozzle up before leaving it

down or storing it.

The air ow can be adjusted by setting the switch lever

(6) to position I, II or III.

Set the switch (6) to position I in order to protect the sur-

rounding surfaces from overheating or in case the work-

piece is lightweight and there is danger of being swept

away by the air ow.

pages-HAG 2000[ED]-2014.indd 4 25.4.2014 г. 10:31:48 ч.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Sparky HAG 2000ED in the language / languages: English, German, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 3,07 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Sparky HAG 2000ED Manual

Product: