604125

Sparky BAR 12E Manual

9
Zoom out
Zoom in
Previous page
1/86
Next page
Original instructions EN
7


When using your cordless angle drill/driver continuously,
the batteries in your battery pack will become hot. You
should let a hot battery pack cool down for approximately
-
tery pack becomes discharged and is hot, the red light
   
down, the red light will glow continuously to indicate fast
charging mode, 1-hour charge time.
 This will occur when continuous use of your tool
causes the battery pack to become hot. It does not occur
under normal conditions.
VII - Know your product


3. Keyless chuck
4. Torque control collar
5. Battery

7. LED charge indicator
VIII - Operation

1. When the trigger switch is depressed, the tool rotates.
Fig. 4
2. The rotation speed can be controlled by varying the
pressure on the trigger switch. Light pressure on the
trigger switch results in low rotation speed, further
pressing results in smooth increase of the rpm to
maximum upon reaching the extreme position.

WaRning: Switch off the power tool prior to
any procedure on it. To avoid involuntary switching on
we recommend removing the battery pack.
Grip rear collar of keyless chuck and rotate front collar
until chuck is opened sufficiently for the bit to be inserted.
Then firmly tighten front collar by hand. Ensure that the
bit is firmly fastened.
To remove a bit, rotate the front chuck collar.

Install the bit that matches the screw, line up the bit in the
grooves of the head of the screw then tighten it.
Push the driver just enough to keep the bit fitting the
head of the screw.
WaRning: Over tightening can result in the
screw breaking or damage to the end of the driver bit.
1. Applying this power tool for too long, shall tighten the
screw excessively and break it.
2. If the machine is held at an angle to the screw being
tightened, the head of the screw may be damaged,
or the specified torque may not be transmitted to the
screw. Always keep the unit and the screw being tight-
ened in a straight line.

-
ing the R-side of the push button. The L-side of the
push button is pushed to turn the bit counter-clockwise.
Fig. 5
WaRning: The push button can not be
switched while the drill is turning. To switch the push
button, stop the machine and then set the push button.

By rotating the torque control collar behind the chuck,
you can adjust the torque to each of the 12 settings.
Fig. 6
The range of 12-torque setting allows better control
when using the drill as screwdriver as it prevents over
tightening of the screws.

1. Open the chuck jaws entirely.

between jaws to engage the left-threaded screw head.
Remove screw by turning clockwise.
3. Place the hex key in the chuck and tighten. Using a wood-
en mallet or similar object, strike the hex key sharply in
counter-clockwise direction. This will loosen the chuck so
it can be unscrewed by hand.
IX - Maintenance
cleaning
 
vents with dry air at least once a week. Wear safety
glasses while performing this.
         
cloth and mild detergent.
WaRning: Although exterior plastic parts
are highly solvent resistant, NEVER use solvents.

 
the charger using a cloth or soft non-metallic brush.
Do not use water or any cleaning solutions.
WaRning: Disconnect the charger from the
AC outlet before cleaning.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sparky BAR 12E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sparky BAR 12E in the language / languages: English, German, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 1,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info