673313
4
Zoom out
Zoom in
Previous page
1/11
Next page
3
Power Source
This system is designed to operate on 230VAC 50Hz house current only. Connecting this
system to any other power source may cause damage to the system and such damage is not
covered by your warranty.
Note: The system has polarized AC plug with one wide blade and one narrow blade. The plug
will only fit into matching polarized AC outlets.
Battery Back Up System
This unit uses a single 9-Volt battery (not included) to maintain the time and alarm settings in
event that it is accidentally unplugged, or you experience a temporary power failure. We
recommend that you install a well-known brand of Alkaline battery for longest life and best
performance. To keep the battery back up system operational you should install a new battery
every 6 to 9 months. Some people find it convenient to replace the back up batteries in their
alarm clocks, clock radios, and smoke detectors too, at the beginning and end of Daylight
Saving Time.
OPERATING INSTRUCTIONS
Setting The Correct Time And Day
NOTE: Connect the power cord to your AC outlet. Make sure to use an outlet that is always ‘live’.
Do not use an outlet that is controlled by a wall switch.
1. When the unit is plugged in for the first time, the clock display will begin flashing “0:00
(AM).
2. Press and hold the CLK-ADJ/PROG. button for at least two seconds until only the Hour digits
continue to flash.
3. While the Hour digits are flashing press the TIME-DN/F.REW or TIME-UP/F.FWD buttons
repeatedly to set the clock to the correct Hour.
4. When the correct hour is flashing, press the CLK-ADJ/PROG. button again. The Minute
digits begin flashing.
5. While the Minute digits are flashing press the TIME-DN/F.REW or TIME-UP/F.FWD buttons
repeatedly to set the clock to the correct Minutes.
6. Press the CLK-ADJ/PROG. button. The Day indicator d:1 ” begins to flash.
7. While the day indicator is flashing, press the TIME-DN/F.REW or TIME-UP/F.FWD buttons
repeatedly to set the display to the correct ‘Day’. (1 = Monday, 2 = Tuesday, etc.)
8. When the correct ‘day’ (digit) appears on the display press the CLK-ADJ/PROG. button once
more to exit the clock-setting mode. The display stops flashing and returns to the correct time
and the clock begin to run.
IMPORTANT: After you press the CLK-ADJ/PROG. button you must make your time
adjustments within 10 seconds while the display is flashing. After 10 seconds the display stops
flashing and no time adjustments can be made. If this occurs you must begin with Step 2
above and start the time adjustment process again.
Listening To The Radio
1. Press the ALARM OFF/POWER button on the top panel to turn the unit ‘On’. The POWER
LED indicator comes on.
2. Press the RADIO/BAND button to select the Radio function. Either the AM/PROG. or the FM
indicator will come on to confirm which band is selected. Press the RADIO/BAND button
again to repeatedly switch between the AM and FM bands.
3. Rotate the TUNING control on the right side panel to tune to the desired station.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Soundmaster URD-750 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Soundmaster URD-750 in the language / languages: English as an attachment in your email.

The manual is 0,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info