611473
27
Zoom out
Zoom in
Previous page
1/60
Next page
25Soundcraft MFXi MPMi User Guide Issue 1210
33
6
6
99
12
12
15 15
0
-
+
33
6
6
99
12
12
15 15
0
-
+
33
6
6
99
12
12
15 15
0
-
+
010
010
010
LR
AUX1
AUX2
FX
BAL
0
PFL
MIX
SUB
PK
SP
MUTE
STE1
STEREO 1
L
R
[MONO]
GAIN
HF
MF
LF
5
0
-5
-10
-20
-30
-10 20dB
10
STE1
1
2
3
6
8
12
4
9
11
5
10
7
STEREO INPUT CHANNELS (MFXi shown)
1 INPUTS STEREO 1/2
These inputs accept 3-pole 6.35mm (1/4”) jacks. Use these inputs for sources such
as keyboards, drum machines, synths, tape machines or processing units. The inputs
are BALANCED for low noise and top quality from professional equipment, but you
can use UNBALANCED sources by wiring up the jacks as shown in the ‘Wiring Up’
section earlier in this manual, although you should then keep cable lengths as short
as possible. Mono sources may be used by plugging into the left jack only.
2 GAIN
The GAIN control sets the level of the channel signal.
3 EQUALISER
HF EQ
Turn to the right to boost high (treble) frequencies, adding crispness to percussion
from drum machines, synths and electronic instruments. Turn to the left to cut these
frequencies, reducing hiss or excessive brilliance. Set the knob in the centre-detented
position when not required. The control has a shelving response giving 15dB of boost
or cut at 12kHz.
MF EQ
Turn to the right to boost mid frequencies by up to 15dB, turn to the left to cut these
frequencies by up to 15dB. The centre frquency of the MF EQ is 720Hz.
LF EQ
Turn to the right to boost low (bass) frequencies, adding extra punch to synths, guitars
and drums. Turn to the left to reduce hum, boominess or improve a mushy sound.
Set the knob to the centre-detented position when not required. The control has a
shelving response giving 15dB of boost or cut at 80Hz.
4 AUX SENDS
These are used to set up separate mixes for FOLDBACK, EFFECTS or recording, and
the combination of each Aux Send is mixed to the respective Aux Output at the rear
of the mixer. For Effects it is useful for the signal to fade up and down with the fader
(this is called POST-FADE), but for Foldback or Monitor feeds it is important for the
send to be independent of the fader (this is called PRE-FADE).
AUX SEND 1 is xed pre-fade, AUX 2 is globally switchable between pre and post-fade
(see master section on page 28). On the MPMi, Aux 3 is xed post-fader. The send
pots are fed with a mono sum of the L & R signals.
AUX 3 SEND (MPMi)
Aux 3 is xed post-fader.
0
0
0
AUX1
AUX2
AUX3
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Soundcraft MFXi at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Soundcraft MFXi in the language / languages: English as an attachment in your email.

The manual is 2,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Soundcraft MFXi

Soundcraft MFXi User Manual - German - 47 pages

Soundcraft MFXi User Manual - French - 56 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info