611447
16
Zoom out
Zoom in
Previous page
1/48
Next page
USER GUIDE
14
CHANNEL DIRECT OUTPUTS
The Direct outputs are on 3-pole A gauge jack sockets, wired as shown on the left, and are impedance
balanced.
HEADPHONES
The PHONES output is a 3-pole A gauge jack, wired as a stereo output as shown, suitable for headphones
of 200W or greater. 8W headphones are not recommended.
POLARITY (PHASE)
You will probably be familiar with the concept of polarity in electrical signals and this is of particular
importance to balanced audio signals. Just as a balanced signal is highly effective at cancelling out
unwanted interference, so two microphones picking up the same signal can cancel out, or cause serious
degradation of the signal if one of the cables has the +ve and -ve wires reversed. This phase reversal can
be a real problem when microphones are close together and you should therefore take care always to
connect pins correctly when wiring audio cables.
GROUNDING AND SHIELDING
For optimum performance use balanced connections where possible and ensure that all signals are
referenced to a solid, noise-free earthing point and that all signal cables have their screens connected to
ground. In some unusual circumstances, to avoid earth `loops’ ensure that all cable screens and other
signal earths are connected to ground only at their source and not at both ends.
If the use of unbalanced connections is unavoidable, you can mimimise noise by following these wiring
guidelines:
• On INPUTS, unbalance at the source and use a twin, screened cable as though it were balanced.
• On OUTPUTS, connect the signal to the +ve output pin, and the ground of the output device to -ve.
If a twin screened cable is used, connect the screen only at the mixer end.
• Avoid running audio cables or placing audio equipment, close to thyristor dimmer units or power
cables.
• Noise immunity is improved significantly by the use of low impedance sources, such as good quality
professional microphones or the outputs from most modern audio equipment. Avoid cheaper high
impedance microphones, which may suffer from interference over long cable runs, even with
well-made cables.
Grounding and shielding is still seen as a black art, and the suggestions above are only guidelines. If your
system still hums, an earth loop is the most likely cause. Two examples of how an earth loop can occur
are shown below.
WARNING! Under NO circumstances must the mains earth be disconnected from the
mains lead.
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Soundcraft M12 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Soundcraft M12 in the language / languages: English as an attachment in your email.

The manual is 4,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Soundcraft M12

Soundcraft M12 User Manual - German - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info