611444
18
Zoom out
Zoom in
Previous page
1/48
Next page
USER GUIDE
16
(e-mail: soundcraft.csd@harman.com)
MONO INPUT CHANNEL
1 DIRECT OUTPUT
The first eight channels have a dedicated Direct Output which allows direct connection to external devices, for
example to feed Tape Machines or effects units.
2 MIC INPUT
The mic input accepts XLR-type connectors and is designed to suit a wide range of BALANCED or
UNBALANCED signals. Professional dynamic, condenser or ribbon mics are best because these will be LOW
IMPEDANCE. You can use low-cost HIGH IMPEDANCE mics, but the level of background noise will be higher.
If you turn the PHANTOM POWER on (top right-hand side of the mixer) the socket provides a suitable
powering voltage for professional condenser mics.
TAKE CARE when using unbalanced sources, which may be damaged by the phantom power voltage on pins
2 & 3 of the XLR connector.
Unplug any mics if you want to use the LINE Input. The input level is set using the GAIN knob.
3 LINE INPUT
Accepts 3-pole `A gauge (TRS) jacks. Use this input for sources other than mics, such as keyboards, drum
machines, synths, tape machines or guitars. The input is BALANCED for low noise and top quality from
professional equipment, but you can use UNBALANCED sources by wiring up the jacks as shown below,
although you should then keep cable lengths as short as possible. Unplug anything in the MIC input if you
want to use this socket. Set the input level using the GAIN knob.
4 IINSERT POINT (ALTERNATIVE DIRECT SEND)
The unbalanced, pre-EQ insert point is a break in the channel signal path, allowing limiters, compressors,
special EQ or other signal processing units to be added in the signal path. The Insert is a 3-pole A gauge
jack socket which is normally bypassed. When a jack is inserted, the signal path is broken, just before the
EQ section.
The Send may be tapped off as an alternative pre-fade, pre-EQ direct output if required, using a lead with
ONLY connect condenser microphones with the +48V
powering OFF, and ONLY turn the +48V powering on or off with all output faders
DOWN, to prevent damage to the mixer or external devices.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Soundcraft M Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Soundcraft M Series in the language / languages: English as an attachment in your email.

The manual is 4,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Soundcraft M Series

Soundcraft M Series User Manual - German - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info