611475
23
Zoom out
Zoom in
Previous page
1/32
Next page
23
Mono Input Channel
1 - MIC INPUT1 - MIC INPUT
1 - MIC INPUT1 - MIC INPUT
1 - MIC INPUT
The mic input accepts XLR-type connectors and is designed to suit a wide range of
BALANCED or UNBALANCED signals. Professional dynamic, condenser or ribbon mics
are best because these will be LOW IMPEDANCE. You can use low-cost HIGH IMPEDANCE
mics, but the level of background noise will be higher. If you press the 48V switch down
the socket provides a suitable powering voltage for professional condenser mics (this is
also known as Phantom Power).
ONLY connect condenser microphones with the
48V powering OFF (switch UP), and ONLY turn the
48V powering on or off with all output faders
DOWN, to prevent damage to the mixer or
external devices.
TAKE CARE when using unbalanced sources,
which may be damaged by the phantom power
voltage on pins 2 & 3 of the XLR connector.
Unplug any mics if you want to use the LINE Input. The input level is set using the GAIN
knob.
2 - 48V (Phant2 - 48V (Phant
2 - 48V (Phant2 - 48V (Phant
2 - 48V (Phant
om Pom P
om Pom P
om P
oo
oo
o
ww
ww
w
er)er)
er)er)
er)
Many professional condenser mics need an external powering voltage, normally 48V,
also known as PHANTOM POWER. This is a method of sending a powering voltage down
the same wires as the mic signal. Each switch supplies the 48V power to four MIC inputs.
The adjacent LED illuminates when the power is active.
DO NOT USE unbalanced mics with 48V switched
on as they may be damaged by the phantom
power voltage. Balanced dynamic mics and leads
can normally be used with 48V switched on
(contact your microphone manufacturer for
guidance)
Mics should always be plugged in, and all output
faders set to minimum before switching 48V ON to
avoid damage to external equipment
3 - LINE INPUT3 - LINE INPUT
3 - LINE INPUT3 - LINE INPUT
3 - LINE INPUT
Accepts 3-pole `A’ gauge (TRS) jacks. Use this high impedance input for sources other
than mics, such as keyboards, drum machines, synths, tape machines or guitars. The
input is BALANCED for low noise and top quality from professional equipment, but you
can use UNBALANCED sources by wiring up the jacks as shown, although you should
then keep cable lengths as short as possible. Unplug anything in the MIC input if you
want to use this socket. Set the input level using the GAIN knob.
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Soundcraft LX 7ii at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Soundcraft LX 7ii in the language / languages: English as an attachment in your email.

The manual is 0,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Soundcraft LX 7ii

Soundcraft LX 7ii User Manual - German - 32 pages

Soundcraft LX 7ii User Manual - French - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info