611452
30
Zoom out
Zoom in
Previous page
1/60
Next page
28
Soundcraft EFX/EPM User Guide Issue 1210
FX PROCESSOR CONTROLS (EFX only)
1. Tempo Button - Tapping this button twice sets the Delay Time of the selected
program. The LED ashes to indicate current tempo. Can be tapped in time with
music source to synchronise the delay.
2. Store Button - Stores program modications to one of the program locations.
Press and hold for three seconds will store the preset in the current location. The LED
will ash rapidly during the store operation and then stay illuminated for 1 second
to show the operation is complete.
3. Pre Delay / Time/ Speed Knob - Controls Pre Delay of the reverbs or the rst
parameter (time or speed related) of the selected effect. The LED illuminates when
the parameter matches the stored setting.
4. Decay / Feedback/Depth Knob - Controls Decay of the reverbs or the second
parameter (feedback or depth related) of the selected effect. The LED illuminates
when the parameter matches the stored setting.
5. Variation - Controls Liveliness or Diffusion (depending on the reverb selected) or
the third parameter of the selected effect. The LED illuminates when the parameter
matches the stored setting.
6. Program Select Knob - Navigates through programs, turning to the required pro-
gram will initiate the loading of the program which take approximately 1 second. The
knob can be rotated clockwise or anticlockwise and will alternate between BANK A
and BANK B every full rotation. The current bank is shown by its illuminated LED,
which ashes if the FX processor is muted. There is a handy aide memoir of the
programs printed on the front panel.
7. Clip LEDThis LED illuminates when either the incoming audio or the processed
audio (within the effect processor) overloads, and causes distortion of the signal.
8. PFL - This switch routes a post effects processor, pre-fade (EFFECTS FADER) signal
to the monitor system.
9. MUTE - This switch mutes the output of the FX processor. It doesn’t mute the PFL
signal or the FX TO AUX 1 pre-fade signal.
10. FX TO AUX 1 - This pot routes a pre-fade and a post-fade signal to the Aux 1-pre
and Aux 1-post busses respectively.
11. EFFECTS FADER - This fader controls the level of the signal, from the FX proces-
sor, routed to the main mix busses.
FX BUS OUT (see diagram on page 24) - This output carries the signal from the FX bus. It could be used as
a second Aux Output if desired, if the FX Processor is not needed at the time.
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Soundcraft EPM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Soundcraft EPM in the language / languages: English as an attachment in your email.

The manual is 3,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info