611451
11
Zoom out
Zoom in
Previous page
1/60
Next page
9
Soundcraft EFX/EPM User Guide Issue 1210
11 PEAK LED This is used to indicate that the signal is close to distorting (clipping) on a
specic channel.
12 INPUT CHANNEL FADER This is used to control the level fed to the Mix Bus and post-fade sends.
13 MIX OUTPUTS (XLR) & Connect these to your analogue recording device, or to your amplication
MONO OUT (¼ Jack) system.
14 MIX INSERTS (¼ Jack) This is a pre-fade break in the signal path which can be used to feed a
dynamics or mastering device. The signal is sent from the tip of the jack plug
and the return path comes back in on the ring of the jack plug.
15 MONITOR O/Ps (¼ Jack) These are used to feed your monitoring system. This can be directly connected
to powered monitors, or indirectly via an amplier to standard monitors.
16 MASTER FADERS These faders control the overall level of the mix outputs.
17 MAIN METERS These show the level of the mix outputs. When the PFL ACTIVE LED is lit, the
meters show the level of the selected PFL signal.
18 MONITOR CONTROL This controls the level of the signal sent to your monitoring system.
19 PHONES CONTROL This controls the level of the signal sent to the headphones jack socket.
20 AUX 1 OUTPUT (¼ Jack) This output can be used to send the channel signal to an artist’s monitors
(headphones/in-ear/stage monitors). It is switchable pre/post fade.
21 AUX CONTROL This switch globally switches the AUX1 feed on all the input modules to be
either pre or post-fade.
22 STEREO INPUTS (¼ Jack) These two inputs can be used to connect line level stereo inputs from key-
boards, sound modules, samplers, computer based audio cards etc. These
inputs pass through a normal channel strip, with EQ, Auxes and a Balance
control.
23 2-TRACK INPUTS Here you can connect the playback from your recording device.
(RCA Phono)
24 2-TRACK CONTROLS Use these to control the 2 Track signal. The MONITOR switch sends the signal
to the monitor outputs and phones, whilst the TO MIX switch sends it to the
main mix.
25 RECORD OUTPUTS You can connect these to the inputs of your recording device.
(RCA Phono)
26 PHANTOM POWER Press this to switch the phantom power (48V) on for condenser microphones.
WARNING: Do Not apply Phantom Power before connecting a
microphone.
27 HEADPHONES (¼ Jack) Plug your headphones into this socket. Recommended headphones imped-
ance is 150 ohms or greater.
28 STEREO RETURN INPUTS This pair of inputs accept 3-pole A gauge (TRS) jacks. Use these inputs for
sources such as keyboards, drum machines, synths or CDs. The inputs are
BALANCED. Mono sources may be used by plugging into the left jack only.
29 STEREO RETURN CONTROL This control sets the level of signal routed to the main mix busses. There is
an associated PK LED to warn of signals which are too high.
30 FX BUS OUTPUT This output carries the signal from the FX bus. It could be used as a second
Aux Output if desired, if the FX Processor is not needed at the time. The FX
sends on the inputs channels to the FX bus are always post-fade.
31 FOOTSWITCH CONNECTOR This is used by the FX Processor, see page 26.
32 LEXICON® FX PROCESSOR See the information starting on page 27
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Soundcraft EFX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Soundcraft EFX in the language / languages: English as an attachment in your email.

The manual is 3,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info