611477

Soundcraft Compact Stagebox Manual

15
Zoom out
Zoom in
Previous page
1/16
Next page
Soundcraft Compact Stagebox User/Installation Guide Page 15
REPLACING I/O MODULES
In order to replace an input or output module - e.g. if more inputs or outputs are required
- rst switch the Compact Stagebox OFF and unplug the mains cable(s).
• Observe the precautions for handling devices sensitive to electrostatic discharge – refer to p. 5.
• For all screws in question a no. 2.5 Allen screwdriver is used.
• Remove the top cover of the Compact Stagebox (2 countersunk screws M4x8 on top, 13 screws
M4x6 around the upper edge).
• Then remove the module concerned. Unplug the at cable from the backplane PCB and the supply
loom from the module.
• Remove the 4 screws M4x6 at the module’s edges.
• Insert the new module and x it with the 4 screws. Connect the at cable to the corresponding
socket on the backplane PCB (for correct connection refer to the illustration below).
• Connect the supply loom to the module. Supply looms are identical for input and output modules,
no particular order has to be followed when reconnecting them. Like the power connections in a PC,
there is one connector more than modules to feed; the fourth connector is not used.
• For xing the top cover it is recommended to tighten all screws only after all of them have been
inserted a few turns into their threads.
• Connect the Compact Stagebox to the mains again, switch it on and press the RECONFIG button
with a small tool (e.g. the Allen screwdriver used before).
• Remember that the new input/output count needs to be congured in your console’s I/O mapping.
Please refer to its user guide.
Input Modules
TOP (A)
MIDDLE (C)
BOTTOM (E)
Output Modules
TOP (A)
MIDDLE (C)
BOTTOM (E)
The 3 module slots are labeled A, C and E; they correspond to the connectors of the backplane PCB ac-
cording to the illustration above. There are 3 connectors on the left for input modules, and 3 on the right
for output modules. Modules must be connected to the correct connector in order to have a correct as-
signment of input and/or output channels.
In the standard conguration (2 input modules in slots A and C, and 1 output module in slot E) the mod-
ules are connected as follows:
Input module A è top connector on the left side of the backplane (P2)
Input module C è middle connector on the left side of the backplane (P13)
Output module E è bottom connector on the right side of the backplane (P20).
… 15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Soundcraft Compact Stagebox at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Soundcraft Compact Stagebox in the language / languages: English as an attachment in your email.

The manual is 0,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info