812373
17
Zoom out
Zoom in
Previous page
1/33
Next page
The priority for the first storage is thus set under priority S2 and for the 2. storage under priority S3.
Tmax Pool / Tmax Pool HE
Switch-off temperature at heat exchanger sensor. If this value is exceeded at the specified sensor, the controller turn off the affiliated
pump or the valve. If this value on the sensor is undershot and the other conditions are fulfilled, the controller will turn on the pump or
the valve.
Temperature values which are set too high can lead to scalding or damage to the system. Scalding protection must be
provided by the customer!
Priority temperature
Temperature threshold for absolute priority charge. In systems with two storage tanks charging of the lower-priority storage tank will
never take place until this temperature at sensor of the higher-priority storage tank is exceeded.
Loading time
Interruption of charging into the lower priority storage. The charging of the lower-priority storage is interrupted after the settable time in
order to check whether the collector has reached a temperature level that allows charging in the higher- priority storage. If so, the pri-
ority storage tank is charged. If not, the increase is measured (See " Increase " on page 17), to check if charging of the priority storage
will be possible shortly.
Increase
Extension of the charging pause due to temperature increase. For precise setting of the charging priorities for systems with multiple
storage tanks, the necessary temperature increase of the collector at which the interruption of the charging into the lower-priority stor-
age tank is extended by one minute is set here. The interruption is extended because the temperature increase of the collector is
expected to enable charging in the higher-priority storage tank soon. As soon as ΔT conditions are met, the priority storage tank is
charged.
If the rise in temperature falls below the set value, then the charging of the lower-priority storage tank is enabled again.
5. Protective Functions
The 'Protective functions‘ can be used by specialists to activate and set various
protective functions.
By no means does the controller replace the safety appliances on site!
System protection
Priority protection function
The system protection should prevent an overheating of the components installed in the system through the forced shut down of the
solar circulation pump. If the value “AS Ton on the collector has been exceeded for 1 Min. the pump will be turned off and not turn on
again in order to protect the collector, for example, from steam. The pump will only be switched on again, when the collector tem-
perature falls below “SP Toff”.
With the system protection (on), there are increased standstill temperatures in the solar collector and therefore an increased
pressure in the system. The operating manuals from the system components must be observed.
Collector protection
Priority protection function
The collector protection prevents the collector from overheating. A forced switching of the pump makes sure that the collector is cooled
through the storage. If the value “KS Ton is exceeded on the collector, the pump will be turned on in order to cool the collector. The
pump is shut down if the value “KS Toff on the collector is not met or the value “KS Tmax Sp.” on the storage is exceeded.
System protection has priority over collector protection! Even if the switch requirements for the collector protection are
present, the solar circulation pump is turned off once AS T on is reached. Normally the values from the system protection
(depending on the maximum temperature of the storage or other components) are higher than the collector protection.
17
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sorel MTDC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sorel MTDC in the language / languages: English as an attachment in your email.

The manual is 2.34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sorel MTDC

Sorel MTDC User Manual - German - 33 pages

Sorel MTDC User Manual - Dutch - 33 pages

Sorel MTDC User Manual - French - 33 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info