812427
5
Zoom out
Zoom in
Previous page
1/6
Next page
5
L:\Bedienanleitungen\...\HR3_englisch_240605.pmd
8.6Menu "06 Special function"
Language = language selection
Please select here the language required to work on all menus.
Mixer ON time = Adapting the mixer running time
The duty cycle is preset to 1 second and may vary in a range
of 0,5...4,5 seconds during steps of 0,5 seconds.
Antifreeze = Antifreeze function
If the outdoor temperature is reduced to 0°C when the antifreeze
function is activated, the target flow temperature is set to at least
20°C in order to prevent the heating circuit from damages by
freezing. If the outdoor temperature exceeds +2°C the normal
operation is restarted. The antifreeze is preset to ON. The
antifreeze function is not valid for the operational modes manual,
target value or OFF.
Manu-calib. = Manual calibration of the probe
The HR3 allows to set of a correction value for each individual
temperature probe, e.g. in order to equalize erroneous
measurings for long probe wirings.
If the value is raised by 1 point, this will result in a correction of
the displayed value of about 0,5 °C. The preset value is 0.
Type Probe3 = Selecting the type of probe3
If a room regulator (RT21) or a standard probe as an additional
temperature display or an external thermostat is connected.
8.7Menu "07 Menu interlocking"
In order to interlock all menus where settings had been performed
and to secure them in this way against unvoluntary misadjusting,
the menu interlocking is to be activated.
If new settings are to be performed, the menu interlocking is to
be deactivated.
8.8Menu "08 Standard values"
With this menu, the original presettings may be loaded and the
user settings are saved and may be restored.
Recommendation: The values which had been set by the special-
ist when commissioning the installation, are to be saved under
personal settings.
07 Menu interlocking Selecting or
confirmation with
08 Standard values Selecting or
confirmation
06 Special function Selecting or
confirmation with
In case of an error, the operational statuses and the settings of
the controller may be displayed and then logged e.g. for a remote
diagnostic by phone.
Programmversion HR3 -
Sensor S1: / /
Sensor S2: / /
Sensor S3: / /
Sollvorlauf
SW / Steilheit /
Betriebsart
Frostschutz / S3 /
Pumpe / Mischer Hzk: Mi:
Tagbetr. / Mischer-Pos
.
/
8.9Menu "09 Service values"
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sorel HR3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sorel HR3 in the language / languages: English as an attachment in your email.

The manual is 0.1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sorel HR3

Sorel HR3 User Manual - German - 6 pages

Sorel HR3 User Manual - French - 6 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info