734406

Sopur Xenon 2 FF Manual

53
Zoom out
Zoom in
Previous page
1/120
Next page
ENGLISH
XENON 2 FF 53 Rev.3.0
6.8 Wheel Alignment
Adjusting the wheel alignment
NOTE: To achieve the very best movement, the rear wheels must be
adjusted to their optimum position, which means correctly adjusting
the wheel alignment. To do this, measure the distance between both
wheels front and rear to ensure that they are parallel to one another.
The difference between both measurements should not exceed 5
mm. The parallel setting can be adjusted by loosening the screws, (1)
and rotating the axle adapter (3).
When finished, make sure that all screws have been properly
tightened, (Fig.6.8.1 to Fig.6.8.2). Re-tighten the Allen screws to 8
Nm.
WARNING!
Be careful, there is a risk of tipping when adjusting the centre of
gravity of the seat!
Adjusting the rear wheelbase width
The rear wheelbase is defined as the distance between the upper
side of the rear wheels and the backrest tubes and is factory set,
(125 mm). This must be increased if more space is to be created
between the tyres and the optional height-adjustable armrests.
When adjusting the rear wheelbase:
• Move the axle adapter (3), in a telescopic manner into the axle
bracket (2), or out of the axle bracket.
• Loosen the Allen screw, (1), on the rear of the axle bracket.
• Move the axle adapter, (3), in or out, until the desired wheelbase is
achieved.
• Re-tighten the Allen screws (1), using a two-stage process:
a) Tighten both Allen screws to a torque of 5 Nm.
b) Tighten both Allen screws for a second time to a torque of 8 Nm.
• Repeat the procedure on the right side of the wheelchair setting
the gap the same as for the left side, (Fig.6.8.1 to Fig.6.8.2).
CAUTION!
• When adjusting the rear wheelbase, set first one wheel and then the
other.
• Wheel alignment needs to be checked and, if necessary, adjusted
after the axle adapter was moved or removed (please refer to
section, ("wheel alignment“).
• Loctite ™ 243 thread locker MUST be used for re-mounting the
Allen screws (1) on the axle-adapter.
Fig. 37Fig.6.8.2
1
3
2
Fig. 30Fig.6.8.1
2
… 53 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sopur Xenon 2 FF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sopur Xenon 2 FF in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 2,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info