734406

Sopur Xenon 2 FF Manual

50
Zoom out
Zoom in
Previous page
1/120
Next page
ENGLISH
XENON 2 FF 50 Rev.3.0
COG, (Centre of Gravity), Setting
To carry out COG adjustment, there are basically 2 different options.
Adjustment can be carried out directly on the axle bracket (Standard
adapter only ) by shifting the crescent-shaped spacers from one side to
the other. To make an adjustment in larger steps, you must change the
position of the axle-stem on the frame.
NOTE:
• COG Adjustments may lead to an unstable wheelchair, likely to tip.
This requires the use of anti-tip tubes.
• An adjustment to the castor angle may be necessary when adjusting
the COG.
Changing the position of the axle stem
Using the quick-release axles, take the wheels out of the angle
adapter.
Undo both screws (1) and remove these completely. Fit the axle stem
in the desired position on the frame, put the screws back into the
perforated plate and then re-tighten the screws. When moving the axle
stem, also move the seat saddle on the frame, (change the axle stem
and the seat saddle). Make sure that the left and right sides are fitted
in the same positions. Use the given torque of 8 Nm (Fig.6.4.4 to
Fig.6.4.5).
COG setting on the standard axle bracket
Adjustment can be carried out directly on the axle bracket (standard
axle bracket only) by shifting the crescent-shaped spacers from one
side to the other. 3 Positions are possible (Fig.6.4.6 to Fig.6.4.8).
Using the quick-release axles, take the wheels out of the axle adapter
(4). Release the Allen screws (1) with an Allen key. Take the lid (2) of
the axle bracket off and arrange the crescent-shaped spacers (3)
according to your desired COG. Put the lid back on.
Re-tighten the Allen screws (1), using a two-stage process:
a) Tighten both Allen screws to a torque of 5 Nm.
b) Tighten both Allen screws for a second time to a torque of 8 Nm.
NOTE: In case the axle adapter was moved or removed whilst ad-
justing the COG, wheel alignment and wheelbase width needs to be
checked and if necessary, adjusted (please refer to the "Wheel Align-
ment" section).
CAUTION!
• Loctite ™ 243 thread locker MUST be used for re-mounting the Allen
screws (1) on the axle-adapter.
Fig.6.4.5
Fig.6.4.4
1
Fig.6.4.6
1
Fig.6.4.7
2
Fig.6.4.8
3 4
… 50 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sopur Xenon 2 FF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sopur Xenon 2 FF in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 2,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info