796240
5
Zoom out
Zoom in
Previous page
1/152
Next page
5GB
Parts for Installation and
Connections
This parts list does not include all the package
contents.
Installation
Mount the unit either inside the trunk (boot) or
under a seat.
Choose the mounting location carefully so the
unit will not interfere with the normal movements
of the driver and it will not be exposed to direct
sunlight or hot air from the heater.
Do not install the unit under the floor carpet,
where the heat dissipation from the unit will be
considerably impaired.
Mounting the unit
First, place the unit where you plan to install it, and
mark the positions of the 4 screw holes on the
mounting board (not supplied). Then drill a 3 mm
(1/8 in) pilot hole at each mark and mount the unit
onto the board with the supplied mounting screws.
The mounting screws are all 14 mm (9/16 in) long, so
make sure that the mounting board is thicker than
14 mm (9/16 in).
Connections
Before making any connections, disconnect the
ground (earth) terminal of the car battery to avoid
short circuits.
Be sure to use speakers with an adequate power
rating. If you use small capacity speakers, they
may be damaged.
This is a Phase-Inverted Amplifier.
Do not connect the terminal of the speaker
system to the car chassis, and do not connect the
terminal of the right speaker with that of the
left speaker.
Install the input and output cords away from the
power supply wire. Running them close together
may generate interference noise.
This unit is a high powered amplifier. Therefore, it
may not perform to its full potential if used with
the speaker cords supplied with the car.
If your car is equipped with a computer system for
navigation or some other purpose, do not remove
the ground (earth) wire from the car battery. If you
disconnect the wire, the computer memory may
be erased. To avoid short circuits when making
connections, disconnect the +12 V power supply
wire until all the other wires have been
connected.
Making the terminal connections
Note
When you tighten the screw, be careful not to apply too
much torque as doing so may damage the screw (the
torque value should be less than 1 N•m).
Connect the +12 V power supply wire only after all
the other wires have been connected.
Be sure to connect the ground (earth) wire of the
unit securely to a metal point of the car. A loose
connection may cause a malfunction of the
amplifier.
Be sure to connect the remote control wire of the
car audio unit to the remote input (REM) terminal.
When using a car audio unit without a remote
output for the amplifier, connect the remote input
(REM) terminal to the accessory power supply.
Installation and Connections

ø4 × 14 mm
(3/16 × 9/16 in)
× 4
Power Connections
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sony XM-GS4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sony XM-GS4 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 12.94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info