796237

Sony XM-4ES Manual

8
Zoom out
Zoom in
Previous page
1/100
Next page
8GB
Connection
•Before making any connections, disconnect the
ground (earth) terminal of the car battery to avoid
short circuits. Connect this amplifier to the +12 V
power supply lead only after all other leads have
been connected.
•This amplifier is designed for negative ground
(earth) 12 V DC operation only.
•Do not operate the amplifier on a weak battery as
the amplifier requires a good power supply for
optimum performance.
•If your car is equipped with a computer system for
purposes such as navigation, disconnecting the
ground (earth) terminal of the car battery may
damage the computer memory. Leave the ground
(earth) lead connected and connect this amplifier
to the +12 V power supply lead only after all other
leads have been connected to prevent short
circuits.
• When connecting and installing the input and
output cables, keep them away from the +12 V
power supply lead. Running them close together
may generate interference noise.
Notes on making connections
• To connect to the terminals on the connector
panel and to adjust various settings, remove the
top cover to access the control panel (top panel).
•When you tighten the screw, be careful not to
apply too much torque as doing so may damage
the terminals or cables.
*1 If you have the factory original or some other car audio
unit without a remote output for the amplifier, connect
the remote input (REMOTE) terminal to the ACC power
supply. In high level input connection, the amplifier can
also be activated without a need for REMOTE connection.
However, this function is not guaranteed for all car audio
units.
*2 Ground (earth) to the car chassis.
+12 V terminal
•Connect the +12 V power supply lead to the +12 V
terminal only after all the other connections have
been completed.
•Use a +12 V power supply lead with a 80 A fuse
attached.
•During full-power operation, a current of more
than 80 A will run through the system. Therefore,
make sure the leads to be connected to the +12 V
terminal are at least 4-Gauge (AWG-4) or have a
sectional area of more than 22.0 mm² (7/8 in²).
• All power leads connected to the positive battery
post should be fused within 450 mm (17 3/4 in) of
the battery post before they pass through any
metal.
•Make sure the leads connecting from the car
battery to the metal point on the car chassis are at
least of a lead gauge equal to that of the +12 V
power supply lead connected from the battery to
the amplifier.
•Make sure the leads connecting from the car
battery to the metal point on the car chassis are
not more than 0-Gauge (AWG-1/0) or have a
sectional area of 55 mm² (2 5/16 in²), and at least
of a lead gauge equal to that of the +12 V power
supply lead connected from the battery to the
amplifier.
REMOTE
+
12 V
GROUND
REMOTE
+
12 V
GROUND
Power Connections
REMOTE
OUT*
1
+12 V REMOTE
GROUND
Fuse (80 A)
to a metal point
on the car chassis
less than 450 mm (17 3/4 in)
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sony XM-4ES at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sony XM-4ES in the language / languages: English, German, Dutch, French, Swedish, Spanish as an attachment in your email.

The manual is 6.31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info