28650
34
Zoom out
Zoom in
Previous page
1/116
Next page
34 (EN)
The power is not turned on.
No picture and no sound.
No picture or no sound.
Picture from INPUT A is
distored.
On-screen displays do not
appear.
Color balance is incorrect.
Picture is too dark.
Picture is not clear.
The LAMP indicator lights up.
The LAMP indicator flashes.
The TEMP indicator lights up.
The Remote Commander
does not work.
The black portions of the left
and right sides brighten when
a picture with normal ratio is
displayed.
The MAIN POWER switch is turned off.
The power has been turned off and on
with the POWER key at a short internal.
Lamp cover is detached.
Air filter cover is detached.
Cable is disconnected.
Input selection is incorrect.
Either the picture or the sound is out off.
Setting for INPUT-A on the SET
SETTING menu is inccorect.
STATUS in the SET SETTING menu has
been set to OFF or ALL OFF.
Picture has not been adjusted properly.
Projector is set to wrong color system.
Lamp is nearing the end of its life.
Contrast or brightness has not been
adjusted properly.
Picture is out of focus.
Condensation has occurred on the lens.
A trouble has prevented the lamp from
lighting.
The lamp cover or the air filter cover is
detached.
The internal temperature is unusually
high.
The Remote Commander batteries are
dead.
The MOUSE/MENU switch has been
switched to the MOUSE position.
You are using the Remote Commander
as a wireless Remote Commander, and
it is connected to the projector.
The unit is influenced of the fluorescent
lamp.
The newly developed optical system also
allows high brightness on the corners of
the screen, so the black portions of the
left and right sides may brighten slightly.
This is not a malfunction.
Press the MAIN POWER switch at the rear of the
projector (see page 15).
Wait for about one minute before turning on the
power with the POWER key.
Close the lamp cover securely (see page 33).
Close the air filter cover securely (see page 33).
Check that the proper connections have been
made (see pages 14 and 32).
Select the input source correctly.
Press the MUTING keys to release the muting
function (see page 16).
Select RGB, COMPONENT, HDTV YP
BPR or
HDTV GBR for INPUT-A on the SET SETTING
menu according to the input signal.
Set STATUS in the SET SETTING menu to ON
(see page 27).
Adjust the picture (see pages 22 and 23).
Set the color system in the SET SETTING menu to
match the color system being input.
Change the lamp (see page 33).
Adjust the contrast or brightness properly.
Adjust the focus (see page 16).
Leave the projector for about two hours with the
power on.
Replace the lamp. If the projector is installed on
the ceiling, consult with qualified personnel.
Attach the cover securely (see page 33).
Check to see that nothing is blocking the
ventilation holes and leave the projector for about
one hour (see page 10).
Replace with new batteries (see page 12).
Set the switch to MENU position.
Disconnect the cable.
Change the setting of SIRCS RECEIVER in the
SET SETTING menu.
Troubleshooting
If the projector appears to be operating erratically, try to diagnose and correct the problem, using the following
guide. If the problem still persists, consult with qualified Sony personnel.
Symptom Cause Remedy
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sony VPLW400Q at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sony VPLW400Q in the language / languages: French as an attachment in your email.

The manual is 1,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sony VPLW400Q

Sony VPLW400Q User Manual - English - 116 pages

Sony VPLW400Q User Manual - Spanish - 116 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info