549897
26
Zoom out
Zoom in
Previous page
1/78
Next page
26
The Connection/Power Menu
The Connection/Power Menu
The Connection/Power menu is used for setting for the connections and power.
Items Item descriptions
LAN Settings
IP Address
Setup
*9
Auto (DHCP): The IP address is assigned automatically from the
DHCP server such as a router.
Manual: To specify the IP Address manually.
WLAN Settings
*10
WLAN
Connection
*8
On/Off: Set the wireless output of the USB wireless LAN module (not
supplied) to On/Off.
WLAN
Network
*14
Access Pt. (Auto)/Access Pt. (Manual)/Client
*11
: Changes modes for
WLAN.
*12
Input-A Signal Sel.
Auto/Computer/Video GBR/Component:
When set to “Auto, selects
the type of video signal input automatically when “Input-A” is selected.
*1
ECO
Lamp Mode High/Standard/Low/Auto
*5 *7
: When set to “High,” the image
becomes brighter, and power consumption becomes higher. When set to
“Low,power consumption is minimized; however, the image will be
darker. When set to “Auto, brightness is adjusted automatically
according to image content. Dark images are projected with brightness
adjusted, leading to energy-saving. Bright images are projected
brightly, without adjusting brightness.
Constant
Brightness
On/Off: Available when the lamp mode is set to High. Outputs light at
a certain brightness.
*13
Auto Power Saving
With No Input Lamp Cutoff: The lamp turns off automatically and power
consumption is reduced if no signal is input for more than 10 minutes.
The lamp lights again when a signal is input or any key is pressed. In
Lamp Cutoff, the ON/STANDBY indicator lights in orange. (page 49)
Standby*
6
: If no signal is input to the unit for more than 10 minutes,
the power turns off automatically, and the unit enters standby mode.
Off: You can deactivate the With No Input.
With Static
Signal
Lamp Dimming
*4 *5 *7
: If an image does not change for about 10
seconds, lamp output is gradually reduced (approximately 10% to
15%*
3
) from that set in the Lamp Mode. Automatically the lamp slowly
darkens to approximately 30% of its lamp output according to the
selected time (with no change to input signal) “5,”10,”15,”20
minutes or “Demo., While dimming the lamp, the message “Lamp
Dimming” appears. If you select “Demo.,” the image will start to
darken about 40 seconds later. When any change in signal is detected,
or an operation (remote control or control panel) is performed, normal
brightness is restored.
Off: You can deactivate the With Static Signal.
Standby Mode*
2
Standard/Low: When set to “Low,” lowers power consumption in
Standby mode.
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sony VPL-SW235 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sony VPL-SW235 in the language / languages: English as an attachment in your email.

The manual is 3,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info