543657
51
Zoom out
Zoom in
Previous page
1/68
Next page
51
Troubleshooting
Others
Remote Commander
“Please check Input-C
Signal Sel.” appears in
spite of inputting the
correct signal from
INPUT C.
The setting of “Input-C Signal Sel. in the Setup menu is incorrect.
c Select “Computer,” “Video GBR” or “Component” correctly
according to the input signal (see page 39).
On-screen display does not
appear.
“Status” in the Setup menu has been set to “Off.
c Set “Status” in the Setup menu to “On” (see page 38).
Color balance is incorrect. The picture has not been adjusted properly.
c Adjust the picture (see page 34).
The projector is set to the wrong color system.
c Set “Color System” in the Setup menu to match the color system
being input (see page 39).
The picture is too dark. • Contrast or brightness has not been adjusted properly.
c Adjust the contrast or brightness in the Picture menu properly
(see page 34).
The lamp has burnt out or is dim.
c Replace the exhausted lamp (see page 46).
The picture is not clear. • The picture is out of focus.
c Adjust the focus (see page 26).
Condensation has accumulated on the lens.
c Leave the projector for about two hours with the power on.
The image extends beyond
the screen.
The APA key has been pressed even though there are black edges
around the image.
c Display the full image on the screen and press the APA key.
c Adjust “Shift” in the Screen menu properly (see page 37).
The picture flickers. “Phase” in the Screen menu has not been adjusted properly.
c Adjust “Phase” in the Screen menu properly (see page 37).
Top, bottom, left and right
side of the image is cut.
Screen setting is not correct.
c Set the “Over Scan” of the Screen Menu to “Off.
c Adjust the position of the picture at “Shift” in “Adjust Signal” of
the Screen Menu.
Symptom Cause and Remedy
The Remote Commander
does not work.
The Remote Commander batteries are dead.
c Replace them with new batteries (see page 17).
The COMMAND ON/OFF switch is set to OFF.
c Set it to ON.
The ID number of the projector assigned in “ID Mode” in the
Installation menu does not match the ID number of the ID MODE
keys on the Remote Commander.
c Assigns the same ID number to the projector and the Remote
Commander, or set “ID Mode” in the Installation menu toAll.
The control panel keys do
not function.
The control panel keys are locked.
c Unlock the control panel keys (see page 41).
Symptom Cause and Remedy
51


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sony VPL-FW300L at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sony VPL-FW300L in the language / languages: English as an attachment in your email.

The manual is 1,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info