51489
14
Zoom out
Zoom in
Previous page
1/91
Next page
14
GB
3 Press u to display “<2-Auto
Calibration>,” then press
ENTER to enter the menu.
4 Press u to display “CAL TYPE,
then press ENTER to enter the
parameter.
5 Press U/u to select the
parameter, then press ENTER
to enter the selection.
6 Press U to display “AUTO CAL
START?,” then press ENTER to
start the measurement.
Measurement starts in five seconds. A
countdown appears on the display.
While the time is counting down, stand
away from the measurement area to
avoid measurement error.
7 Measurement starts.
The measurement process will take
approximately 10 seconds. Wait until the
measurement process completes.
Tip
When special speakers, such as dipole speakers, are
used, the measurements may not be performed
correctly or auto calibration cannot be performed.
To cancel auto calibration
Auto calibration is cancelled when you change
the volume, change the input source, change
the speaker selection, press MUTING, or
connect headphones.
1 Confirm the measurement
result.
When the measurement ends, a beep
sounds and the measurement result
appears on the display.
2 Press U/u repeatedly to select
the item, then press ENTER.
When error codes appear
Try the remedies and re-perform the auto
calibration.
Calibration
type
Explanation
ENGINEER Sets the frequency
characteristics to a set that
matches that of the Sony
listening room standard.
FULL FLAT Makes the measurement of
frequency from each
speaker flat.
Confirming/saving the
measurement results
Measurement
result
Display Explanation
When the
measurement
process
completes
properly
COMPLETE
Proceed to step
2.
When the
measurement
process fails
ERROR
CODE XX
See “When
error codes
appear” (page
14).
Item Explanation
RETRY Re-performs the auto
calibration.
SAVE EXIT Saves the measurement
results and exits the setting
process.
WRN CHECK Displays a warning
concerning the
measurement results. See
“When you select “WRN
CHECK”” (page 15).
EXIT Exits the setting process
without saving the
measurement results.
Error code Cause and remedies
CODE 31 SPEAKERS (OFF/A/B/A+B) is
set to OFF. Select A or B and re-
perform the auto calibration.
When using a bi-wiring
connection, set SPEAKERS
(OFF/A/B/A+B) to A+B.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sony TA-FA1200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sony TA-FA1200 in the language / languages: English, Polish, Swedish, Spanish as an attachment in your email.

The manual is 3,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sony TA-FA1200

Sony TA-FA1200 User Manual - German, Dutch, French, Italian - 95 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info