601264
6
Zoom out
Zoom in
Previous page
1/60
Next page
STR-DE695 4-247-631-12 (1) US
FM Stereo
FM-AM Receiver
4-247-631-12(1)
STR-DE695
Owner’s Record
The model and serial numbers are located at the rear of the unit. Record the serial
number in the space provided below. Refer to them whenever you call upon your Sony
dealer regarding this product.
Model No. Serial No.
© 2003 Sony Corporation
Operating Instructions
01US01COVSEI.p65 3/21/03, 9:03 AM1
2
US
STR-DE695 4-247-631-12 (1) US
WARNING
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
To prevent fire, do not cover the ventilation of the
apparatus with newspapers, table-cloths, curtains,
etc. And don’t place lighted candles on the apparatus.
To prevent fire or shock hazard, do not place objects
filled with liquids, such as vases, on the apparatus.
Don’t throw away the battery with
general house waste, dispose of it
correctly as chemical waste.
Do not install the appliance in a confined space, such
as a bookcase or built-in cabinet.
For customers in the United States
This symbol is intended to alert the
user to the presence of uninsulated
“dangerous voltage” within the
product’s enclosure that may be of
sufficient magnitude to constitute a
risk of electric shock to persons.
This symbol is intended to alert the
user to the presence of important
operating and maintenance (servicing)
instructions in the literature
accompanying the appliance.
WARNING
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and
receiver.
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
– Consult the dealer or an experienced radio/TV
technician for help.
CAUTION
You are cautioned that any changes or modification
not expressly approved in this manual could void
your authority to operate this equipment.
Note to CATV system installer:
This reminder is provided to call CATV system
installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as
close to the point of cable entry as practical.
For customers in Canada
CAUTION
TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
CAUTION
TO PREVENT ELECTRIC SHOCK, DO NOT USE
THIS POLARIZED AC PLUG WITH AN
EXTENSION CORD, RECEPTACLE OR OTHER
OUTLET UNLESS THE BLADES CAN BE FULLY
INSERTED TO PREVENT BLADE EXPOSURE.
ENERGY STAR
®
is a U.S. registered
mark.
As an
E
NERGY
S
TAR
®
partner, Sony
Corporation has determined that this
product meets the
E
NERGY
S
TAR
®
guidelines for energy efficiency.
This receiver incorporates Dolby* Digital and Pro
Logic Surround and the DTS** Digital Surround
System.
* Manufactured under license from Dolby
Laboratories.
“Dolby”, “Pro Logic” and the double-D symbol
are trademarks of Dolby Laboratories.
** “DTS”, “DTS-ES Extended Surround” and
“Neo: 6” are trademarks of Digital Theater
Systems, Inc.
01US02TOCSEI.p65 3/21/03, 9:03 AM2
3
US
STR-DE695 4-247-631-11 (1) US
Table of Contents
List of Button Locations and
Reference Pages
Main unit ............................................... 5
Hooking Up the Components
Required cords ....................................... 6
Antenna hookups ................................... 7
Audio component hookups .................... 8
Video component hookups .................... 9
Digital component hookups ................. 10
Multi channel input hookups ............... 12
Other hookups ..................................... 13
Hooking Up and Setting Up
the Speaker System
Speaker system hookups ..................... 15
Performing initial setup operations ..... 17
Multi channel surround setup .............. 17
Checking the connections .................... 22
Basic Operations
Selecting the component ..................... 23
Changing the display ........................... 24
Enjoying Surround Sound
Using only the front speakers
(2 Channel Stereo) ........................ 25
Enjoying higher fidelity sound ............ 25
Selecting a sound field ........................ 26
Selecting the surround back decoding
mode (SURR BACK
DECODING) ................................ 28
Understanding the multi channel
surround displays .......................... 30
Customizing sound fields .................... 31
Receiving Broadcasts
Direct tuning ........................................ 34
Automatic tuning ................................. 35
Preset tuning ........................................ 35
Other Operations
Naming preset stations and program
sources ........................................... 37
Recording ............................................ 37
Using the Sleep Timer ......................... 38
Adjustments using the CUSTOM
menu .............................................. 39
Changing the command mode of the
receiver .......................................... 39
CONTROL A1II control system ......... 40
Operations Using the Remote
RM-PP412
Before you use your remote ................ 42
Remote button description ................... 42
Selecting the command mode of the
remote ............................................ 46
Programming the remote ..................... 46
Additional Information
Precautions .......................................... 50
Troubleshooting ................................... 50
Specifications ...................................... 53
Tables of settings using the MAIN
MENU button ................................ 56
Adjustable parameters for each sound
field ............................................... 57
4
US
STR-DE695 4-247-631-11 (1) US
R
R
L
L
L
L
R
B
ACK
FRONT B
FRONT A
SURROUND
AC OUTLET
IMPEDANCE USE 8-16
K
ERS
4-XXX-XXX-XX AA
Area code
About This Manual
About area codes
The area code of the receiver you purchased is
shown on the lower portion of the rear panel (see
the illustration below).
Any differences in operation, according to the
area code, are clearly indicated in the text, for
example, “Models of area code AA only”.
Tip
The instructions in this manual describe the controls
on the receiver. You can also use the controls on the
supplied remote if they have the same or similar
names as those on the receiver. For details on the use
of your remote, see pages 42–49.
Note for the supplied remote
RM-PP412
The TV/SAT, PHONO, SOURCE, DIRECT,
AAC BI-LING, 12 and ON SCREEN buttons
on the remote are not available.
5
US
List of Button Locations and Reference Pages
STR-DE695 4-247-631-11 (1) US
?/1
g
qjqkqlw;wawswd wjwkwle;eaesedef wh wfwg
1235
9
0
6qaqs
qd qf qg qh
7
4
8
List of Button Locations and Reference Pages
Main unit
MD/TAPE q; (23)
MEMORY ea (35)
MOVIE (button/indicator) wg (26,
51)
MULTI CHANNEL DECODING
(indicator) ws (23)
MULTI CH IN wd (23)
MUSIC (button/indicator) wf (26,
27, 51)
P – U
PHONES (jack) ef (24, 30, 51)
PRESET TUNING +/– wl
(35, 36, 54)
SPEAKERS (OFF/A/B/A+B) 2
(15, 24, 50)
SURR BACK DECODING wk
(28, 39)
SURR BACK DECODING
(indicator) qg (28)
TUNER FM/AM qs (23, 35, 36,
37)
TUNING +/– e; (35)
V – Z
VIDEO 1 6 (23)
VIDEO 2 7 (23)
VIDEO 3 8 (23)
VIDEO 3 INPUT (jacks) ed (9)
NUMBERS AND SYMBOLS
2CH (button/indicator) wj (25,
27, 33)
?/1 (power) 1 (17, 22, 33, 39
54)
</> wa (18, 32, 33, 37, 39, 56)
ALPHABETICAL ORDER
A – H
A.F.D. (button/indicator) wh (25–
27)
AUX qf (23)
CD/SACD qa (23)
DIMMER 4 (24)
DISPLAY 3 (24, 52)
Display qd (24)
DVD 9 (23)
ENTER ql (17, 37, 39)
FM MODE es (34)
I – O
INPUT MODE qj (23)
IR (receptor) 5 (42, 52)
Jog dial w; (18, 32, 33, 37, 39,
56)
MAIN MENU qk (18, 32, 33, 37,
39, 56)
MASTER VOLUME qh (22, 24,
50)
How to use this page
Use this page to find the location of buttons that are
mentioned in the text.
Illustration number
r
DISPLAY 3 (24, 52)
RR
Name of button/part Reference page
6
US
STR-DE695 4-247-631-11 (1) US
Required cords
The following optional connection cords AI are required when you hook up the components
(pages 8 – 14).
Hooking Up the Components
Before you get started
Turn off the power to all components before making any connections.
Do not connect the AC power cord until all of the connections are completed.
Be sure to make connections firmly to avoid hum and noise.
When connecting an audio/video cord, be sure to match the color-coded pins to the appropriate jacks on
the components: yellow (video) to yellow; white (left, audio) to white; and red (right, audio) to red.
When you connect optical digital cords, insert the cord plugs straight in until they click into place.
Do not bend or tie the optical digital cord.
A Audio cord (not supplied)
White (L)
Red (R)
B Audio/video cord (not supplied)
Yellow (video)
White (L/audio)
Red (R/audio)
C Video cord (not supplied)
Yellow
D S-video cord (not supplied)
E Optical digital cord (not supplied)
F Coaxial digital cord (not supplied)
G Monaural audio cord (not supplied)
Black
Tip
Audio cord A can be torn into two monaural audio
cords G.
H Component video cord (not supplied)
Green
Blue
Red
I Monaural mini-plug cord (not supplied)
Black
Hooking Up the Components
7
US
STR-DE695 4-247-631-11 (1) US
Antenna hookups
FM wire antenna
(supplied)
AM loop antenna
(supplied)
Notes on antenna hookups
To prevent noise pickup, keep the AM loop
antenna away from the receiver and other
components.
Be sure to fully extend the FM wire antenna.
After connecting the FM wire antenna, keep it
as horizontal as possible.
Y
P
B/B—Y
P
R/R—Y
y
AM
FM
75
COAXIAL
DIGITAL
ANTENNA
MD/TAPE
CD
/
SACD
OPTICAL
VIDEO 2
IN
MD/
TAPE
IN
MD/
TAPE
OUT
CD/
SACD
IN
DVD
IN
COAXIAL
IN OUT
IN
AUX
IN
DVD
S-VIDEO
IN
VIDEO IN
L
R
L
R
L
R
VIDEO 2
S-VIDEO
IN
VIDEO IN
VIDEO 1
AUDIO OUT AUDIO IN
S-VIDEO
OUT
S-VIDEO
IN
VIDEO OUT VIDEO IN
S-VIDEO
OUT
VIDEO OUT
DVD
IN
VIDEO 2
IN
MONITOR
OUT
L
R
FRONT SURROUND
SUB
WOOFER
SUB
WOOFER
CENTER
MONITOR
CTRL A1 II
COMPONENT VIDEO
AUDIO IN AUDIO IN
MULTI CH IN PRE OUT
L
R
* The shape of the connector varies depending on the area code.
*
8
US
STR-DE695 4-247-631-11 (1) US
Y
P
B
/BY
P
R
/RY
y
AM
FM
75
COAXIAL
DIGITAL
ANTENNA
MD/TAPE
CD
/
SACD
OPTICAL
VIDEO 2
IN
MD/
TAPE
IN
MD/
TAPE
OUT
CD/
SACD
IN
DVD
IN
COAXIAL
IN OUT
IN
AUX
IN
DVD
S-VIDEO
IN
VIDEO IN
L
R
L
R
L
R
VIDEO 2
S-VIDEO
IN
VIDEO IN
VIDEO 1
AUDIO OUT AUDIO IN
S-VIDEO
OUT
S-VIDEO
IN
VIDEO OUT VIDEO IN
S-VIDEO
OUT
VIDEO OUT
DVD
IN
VIDEO 2
IN
MONITOR
OUT
L
R
FRONT SURROUND
SUB
WOOFER
SUB
WOOFER
CENTER
MONITOR
CTRL A1 II
COMPONENT VIDEO
AUDIO IN AUDIO IN
MULTI CH IN PRE OUT
L
R
INOUT
LINE
L
R
LINE
INPUT OUTPUT
LINE
L
R
OUTPUT
ç
ç
AA
A
MD or Tape deck
CD or Super Audio
CD player
Audio component hookups
Hooking Up the Components
9
US
STR-DE695 4-247-631-11 (1) US
Y
P
B
/BY
P
R
/RY
y
AM
FM
75
COAXIAL
DIGITAL
ANTENNA
MD/TAPE
CD
/
SACD
OPTICAL
VIDEO 2
IN
MD/
TAPE
IN
MD/
TAPE
OUT
CD/
SACD
IN
DVD
IN
COAXIAL
IN OUT
IN
R
R
L
RL
RL
L
AUX
IN
DVD
S-VIDEO
IN
VIDEO IN
L
R
L
R
L
R
VIDEO 2
S-VIDEO
IN
VIDEO IN
VIDEO 1
AUDIO OUT AUDIO IN
S-VIDEO
OUT
S-VIDEO
IN
VIDEO OUT VIDEO IN
S-VIDEO
OUT
VIDEO OUT
DVD
IN
VIDEO 2
IN
MONITOR
OUT
CENTER
SURROUND BACK
FRONT B
FRONT A
SURROUND
L
R
FRONT SURROUND
SUB
WOOFER
SUB
WOOFER
CENTER
MONITOR
CTRL A1 II
COMPONENT VIDEO
AC
AUDIO IN AUDIO IN
MULTI CH IN PRE OUT
IMPEDANCE USE 8-16
SPEAKERS
L
R
VIDEO
OUT
R
AUDIO
OUT
VIDEO
IN
AUDIO
IN
OUTPUTINPUT
L
IN
AUDIO OUT VIDEO
OUT
L
R
OUTPUT
VIDEO
OUT
R
AUDIO
OUT
OUTPUT
L
VIDEO
IN
INPUT
Ç
INOUT
Ç
Ç
C
B
BBB
B
H
COMPONENT VIDEO
Video component hookups
To the VIDEO
3 INPUT jacks
Camcorder
or video
game
TV monitor
DVD player
Note on video component
hookups
You can connect your TV’s audio output jacks
to the VIDEO 2 AUDIO IN jacks on the
receiver and apply sound effects to the audio
from the TV. In this case, do not connect the
TV’s video output jack to the VIDEO 2
VIDEO IN jack on the receiver. If you are
connecting a separate satellite tuner, connect
both the audio and video output jacks to the
receiver as shown above.
If you have a DVD player, TV or satellite tuner
with COMPONENT VIDEO (Y, B-Y, R-Y)
output jacks and a monitor with COMPONENT
VIDEO input jacks, use a component video
cord (not supplied) to connect to the receiver.
Tip
When using the S-video jacks instead of the video
jacks, your monitor must also be connected via an
S-video jack. S-video signals are on a separate bus
from the video signals and will not be output through
the video jacks.
Note
On this receiver, the component video signals are not
compatible with S-video signals or video signals.
VCR
Satellite
tuner or
VCR
10
US
STR-DE695 4-247-631-11 (1) US
Y
P
B
/B—Y
P
R
/R—Y
y
AM
FM
75
COAXIAL
DIGITAL
ANTENNA
MD/TAPE
CD
/
SACD
OPTICAL
VIDEO 2
IN
MD/
TAPE
IN
MD/
TAPE
OUT
CD/
SACD
IN
DVD
IN
COAXIAL
IN OUT
IN
AUX
IN
DVD
S-VIDEO
IN
VIDEO IN
L
R
L
R
L
R
VIDEO 2
S-VIDEO
IN
VIDEO IN
VIDEO 1
AUDIO OUT AUDIO IN
S-VIDEO
OUT
S-VIDEO
IN
VIDEO OUT VIDEO IN
S-VIDEO
OUT
VIDEO OUT
DVD
IN
VIDEO 2
IN
MONITOR
OUT
L
R
FRONT SURROUND
SUB
WOOFER
SUB
WOOFER
CENTER
MONITOR
CTRL A1 II
COMPONENT VIDEO
AUDIO IN AUDIO IN
MULTI CH IN PRE OUT
L
R
VIDEO
OUT
AUDIO
OUT
OUTPUT
DIGITAL
COAXIAL
OUTPUT
VIDEO
OUT
AUDIO
OUT
OUTPUT
DIGITAL
OPTICAL
OUTPUT
BE
F
B
R
L
R
L
Digital component hookups
DVD player
(etc.)*
Connect the digital output jacks of your DVD player and satellite tuner (etc.) to the receiver’s digital
input jacks to bring the multi channel surround sound of a movie theater into your home. To fully
enjoy multi channel surround sound, five speakers (two front speakers, two surround speakers, and a
center speaker) and a sub woofer are required. You will also need a surround back speaker for 6.1
channel surround sound.
Satellite tuner or
DVD player*
* Make either coaxial or optical connections. We recommend making coaxial connections instead of optical
connections.
Hooking Up the Components
11
US
STR-DE695 4-247-631-11 (1) US
Y
P
B
/BY
P
R
/RY
y
AM
FM
75
COAXIAL
DIGITAL
MD/TAPE
CD
/
SACD
OPTICAL
VIDEO 2
IN
MD/
TAPE
IN
MD/
TAPE
OUT
CD/
SACD
IN
DVD
IN
COAXIAL
IN OUT
IN
AUX
IN
DVD
S-VIDEO
IN
VIDEO IN
L
R
L
R
L
R
VIDEO 2
S-VIDEO
IN
VIDEO IN
VIDEO 1
AUDIO OUT AUDIO IN
S-VIDEO
OUT
S-VIDEO
IN
VIDEO OUT VIDEO IN
S-VIDEO
OUT
VIDEO OUT
DVD
IN
VIDEO 2
IN
MONITOR
OUT
L
R
FRONT SURROUND
SUB
WOOFER
SUB
WOOFER
CENTER
MONITOR
CTRL A1 II
COMPONENT VIDEO
AUDIO IN AUDIO IN
MULTI CH IN PRE OUT
L
R
INOUT
ç
ç
ç
LINELINE
INPUT OUTPUT
DIGITAL
IN
OPTICAL
OUT
IN
E
OUT
ç
EAA
L
R
ANTENNA
Connect the digital output jacks of your MD or tape deck to the receiver’s digital input jack and
connect the digital input jacks of your MD or tape deck to the receiver’s digital output jack. These
connections allow you to make digital recordings of TV broadcasts, etc.
MD or tape deck
Notes
You cannot make digital recordings when the source is a multi channel digital source.
All the OPTICAL and COAXIAL jacks are compatible with 96 kHz, 48 kHz, 44.1 kHz and 32 kHz sampling
frequencies.
It is not possible to record analog signals to the components connected to MD/TAPE and VIDEO jacks with
only digital connections. To record analog signals, make analog connections. To record digital signals, make
digital connections.
The sound is not output when you play a Super Audio CD disc on the Super Audio CD player connected to the
CD/SACD OPTICAL IN jack on this unit. Connect to the analog input jacks (CD/SACD IN jacks). Refer to the
operating instructions supplied with the Super Audio CD player.
12
US
STR-DE695 4-247-631-11 (1) US
Multi channel input hookups
Although this receiver incorporates a multi channel decoder, it is also equipped with multi channel
input jacks. These connections allow you to enjoy multi channel software encoded in formats other
than Dolby Digital and DTS. If your DVD player is equipped with multi channel output jacks, you
can connect them directly to the receiver to enjoy the sound of the DVD player’s multi channel
decoder. Alternatively, the multi channel input jacks can be used to connect an external multi channel
decoder.
To fully enjoy multi channel surround sound (5.1 channel), five speakers (two front speakers, two
surround speakers, and a center speaker) and a sub woofer are required. You will also need a
surround back speaker for 6.1 channel surround sound. Refer to the operating instructions supplied
with your DVD player, multi channel decoder, etc., for details on the multi channel hookups.
Notes
When using the connections described below, adjust the level of the surround speakers and sub woofer from the
DVD player or multi channel decoder.
See page 15 for details on speaker system hookup.
DVD player, CD/Super
Audio CD player,
Multichannel decoder, etc.
Y
P
B
/BY
P
R
/RY
y
AM
FM
75
COAXIAL
DIGITAL
ANTENNA
MD/TAPE
CD
/
SACD
OPTICAL
VIDEO 2
IN
MD/
TAPE
IN
MD/
TAPE
OUT
CD/
SACD
IN
DVD
IN
COAXIAL
IN OUT
IN
AUX
IN
DVD
S-VIDEO
IN
VIDEO IN
L
R
L
R
L
R
VIDEO 2
S-VIDEO
IN
VIDEO IN
VIDEO 1
AUDIO OUT AUDIO IN
S-VIDEO
OUT
S-VIDEO
IN
VIDEO OUT VIDEO IN
S-VIDEO
OUT
VIDEO OUT
DVD
IN
VIDEO 2
IN
MONITOR
OUT
L
R
FRONT SURROUND
SUB
WOOFER
SUB
WOOFER
CENTER
MONITOR
CTRL A1 II
COMPONENT VIDEO
AUDIO IN AUDIO IN
MULTI CH IN PRE OUT
L
R
L
R
FRONT
SURROUND
SUB
WOOFER
AAG G
MULTI CH OUT
CENTER
Hooking Up the Components
13
US
STR-DE695 4-247-631-11 (1) US
Y
P
B
/BY
P
R
/RY
y
AM
FM
75
COAXIAL
DIGITAL
ANTENNA
MD/TAPE
CD
/
SACD
OPTICAL
VIDEO 2
IN
MD/
TAPE
IN
MD/
TAPE
OUT
CD/
SACD
IN
DVD
IN
COAXIAL
IN OUT
IN
AUX
IN
DVD
S-VIDEO
IN
VIDEO IN
L
R
L
R
L
R
VIDEO 2
S-VIDEO
IN
VIDEO IN
VIDEO 1
AUDIO OUT AUDIO IN
S-VIDEO
OUT
S-VIDEO
IN
VIDEO OUT VIDEO IN
S-VIDEO
OUT
VIDEO OUT
DVD
IN
VIDEO 2
IN
MONITOR
OUT
L
R
FRONT SURROUND
SUB
WOOFER
SUB
WOOFER
CENTER
MONITOR
CTRL A1 II
COMPONENT VIDEO
AUDIO IN AUDIO IN
MULTI CH IN PRE OUT
L
R
CONTROL A1
I
LINE
L
R
OUTPUT
IN
ç
A
Other hookups
If you have a Sony CD changer with a
COMMAND MODE selector
If your CD changer’s COMMAND MODE
selector can be set to CD 1, CD 2, or CD 3,
be sure to set the command mode to “CD 1”
and connect the changer to the CD jacks on
the receiver.
However, if you have a Sony CD changer
with VIDEO OUT jacks, set the command
mode to “CD 2” and connect the changer to
the VIDEO 2 jacks on the receiver.
CD player, tape
deck, MD deck, etc.
continued
CONTROL A1 hookup
If you have a CONTROL A1 compatible
Sony CD player, Super Audio CD player,
tape deck or MD deck
Use a monaural mini-plug cord (not
supplied) to connect the CONTROL A1II
jack on the CD player, Super Audio CD
player, tape deck or MD deck to the CTRL
A1II jack on the receiver. Refer to
“CONTROL A1II control system” on page
40 and the operating instructions supplied
with your CD player, Super Audio CD
player, tape deck or MD deck for details.
Note
If you make CONTROL A1II connections from
the receiver to an MD deck that is also connected
to a computer, do not operate the receiver while
using the “Sony MD Editor” software. This may
cause a malfunction.
14
US
STR-DE695 4-247-631-11 (1) US
AC power cord
Connecting the AC power
cord
* The configuration, shape, and number of AC outlets
vary according to the model and country to which
the receiver is shipped.
Before connecting the AC power cord of this
receiver to a wall outlet, connect the speaker
system to the receiver (page 15).
Connect the AC power cord(s) of your audio/
video components to a wall outlet.
If you connect other audio/video components to
the AC OUTLET(s) on the receiver, the
receiver will supply power to the connected
component(s), allowing you to turn the whole
system on or off when you turn the receiver on
or off.
Caution
Make sure that the total power consumption of the
component(s) connected to the receiver’s AC
OUTLET(s) does not exceed the wattage stated on the
rear panel. Do not connect high-wattage electrical
home appliances such as electric irons, fans, or TVs
to this outlet.
L
L
L
L
R
ONT B
AC OUTLET
E 8-16
b
AC OUTLET*
Other hookups (continued)
To a
wall outlet
AUX AUDIO IN hookup
If you have an individual audio component
(except PHONO)
Use the audio cords to connect the LINE OUT
jacks on the CD player, tape deck or MD deck
to the AUX IN jacks on the receiver so that you
can listen to stereo sources in surround sound.
Hooking Up and Setting Up the Speaker System
15
US
STR-DE695 4-247-631-11 (1) US
Hooking Up and Setting Up the Speaker System
Front speaker A
(L)
Front speaker A
(R)
Surround speaker
(L)
Surround speaker
(R)
Active sub woofer
* If you have an additional front speaker system, connect them to the SPEAKERS FRONT B terminals.
You can select the front speakers you want to use with the SPEAKERS (OFF/A/B/A+B) button (page 24).
IMPEDANCE USE 8-16
SPEAKERS
SPEAKERS
Y
P
B
/B—Y
P
R
/R—Y
R
R
L
RL
RL
L
S-VIDEO
OUT
VIDEO OUT
DVD
IN
VIDEO 2
IN
MONITOR
OUT
CENTER
SURROUND BACK
SURROUND
L
R
FRONT SURROUND
SUB
WOOFER
SUB
WOOFER
CENTER
MONITOR
CTRL A1 II
COMPONENT VIDEO
AC OUTLET
MULTI CH IN PRE OUT
IMPEDANCE USE 8-16
INPUT
AUDIO
IN
B
E
e
Ee
A
A
E
e
A
E
e
A
E
e
A
E
e
A
SPEAKERS
FRONT B*
FRONT A
SPEAKERS
FRONT B
Surround back
speaker
continued
Speaker system hookups
Required cords
A Speaker cords (not supplied)
(+)
(–)
B Monaural audio cord (not supplied)
Black
Center speaker
16
US
STR-DE695 4-247-631-11 (1) US
Stripped cords are touching each other
due to excessive removal of insulation.
Stripped cords are not fully attached and
are touching the rear panel of the receiver.
After connecting all the components,
speakers, and AC power cord, output
a test tone to check that all the
speakers are connected correctly.
For details on outputting a test tone,
see page 22.
If no sound is heard from a speaker while
outputting a test tone or a test tone is output
from a speaker other than the one whose name
is currently displayed on the receiver, the
speaker may be short-circuited. If this happens,
check the speaker connection again.
To avoid damaging your
speakers
Make sure that you turn down the volume
before you turn off the receiver. When you turn
on the receiver, the volume remains at the level
you turn off the receiver.
Speaker system hookups (continued)
Notes
Twist the stripped ends of the speaker cords about
2/3 inch. Be sure to match the speaker cord to the
appropriate terminal on the components: + to + and
– to –. If the cords are reversed, the sound will be
distorted and will lack bass.
If you use speakers with low maximum input rating,
adjust the volume carefully to avoid excessive
output on the speakers.
To avoid short-circuiting the
speakers
Short-circuiting of the speakers may damage
the receiver. To prevent this, make sure to take
the following precautions when connecting the
speakers.
Make sure the stripped ends of each
speaker cord does not touch another
speaker terminal, the stripped end of
another speaker cord, or the metal parts of
the receiver.
Examples of poor conditions of the
speaker cord
Stripped speaker cord is touching another
speaker terminal.
Hooking Up and Setting Up the Speaker System
17
US
STR-DE695 4-247-631-11 (1) US
Performing initial setup
operations
Once you have hooked up the speakers and
turned on the power, clear the receiver’s
memory. Then specify the speaker parameters
(size, position, etc.) and perform any other
initial setup operations necessary for your
system.
Tip
To check the audio output during settings (to set up
while outputting the sound), check the connection
(page 22).
Clearing the receiver’s
memory
Before using your receiver for the first time, or
when you want to clear the receiver’s memory,
do the following.
1 Turn off the receiver.
2 Hold down ?/1 for 5 seconds.
“PUSH” and “ENTER” appears in the
display alternatingly.
3 Press ENTER.
After “CLEARING” appears in the display
for a while, “CLEARED” appears.
The following are reset to their factory
settings.
All settings in the SET UP, CUSTOM,
LEVEL and EQ menus.
The sound field memorized for each
input selector and preset station.
All sound field parameters.
All preset stations.
All index names for input selector and
preset stations.
The master volume is set to
“VOL MIN”.
45°
90°
20°
A A
B
CC
D
Performing initial setup
operations
Before using your receiver for the first time,
adjust SET UP parameters so that the receiver
correspond to your system. For the adjustable
parameters, see the table on page 56. See pages
17–22 for speaker settings and page 39 for
other settings.
Multi channel surround
setup
For the best possible surround sound, all
speakers should be the same distance from the
listening position (A).
However, the receiver lets you place the center
speaker up to 5 feet closer (B), the surround
speakers up to 15 feet closer (C) and the
surround back speaker up to 15 feet closer (D)
to the listening position.
The front speakers can be placed from 3 to 23
feet from the listening position (A).
You can place the surround speakers either
behind you or to the side, depending on the
shape of your room (etc.).
When placing surround speakers to your side
(long room)
continued
18
US
STR-DE695 4-247-631-11 (1) US
Multi channel surround setup
(continued)
45°
90°
20°
A A
B
CC
D
3 Turn the jog dial to select the setting
you want.
The setting is entered automatically.
4 Repeat steps 2 and 3 until you have set
all of the parameters that follow.
Initial settings
Parameter Initial setting
SW
(SUB WOOFER) S.W. XXX YES
L
R
(FRONT) XXXXX LARGE
C
(CENTER) XXXXX LARGE
SL
SR
(SURROUND) XXXXX LARGE
S B
(SURR BACK) XXX YES
L
R
DIST. XX ft. 10 ft.
C
DIST. XX ft. 10 ft.
SL
SR
DIST. XX ft. 10 ft.
S B
DIST. XX ft. 10 ft.
SL
SR
XXXXXXX SIDE/LO
x Sub woofer selection (
SW
S.W. XXX)
If you connect a sub woofer, select “YES”.
If you do not connect a sub woofer, select
“NO”. This activates the bass redirection
circuitry and outputs the LFE signals from other
speakers.
In order to take full advantage of the Dolby
Digital bass redirection circuitry, we
recommend that you set the cut off frequency
on the sub woofer as high as possible.
When placing surround speakers behind you
(wide room)
Tips
When you set up the surround back speaker, set the
speaker at least 1 meter behind the listening
position. It is recommended to place the speaker at
an equal distance from the surround left and right
speakers. If there is no space behind the listening
position, set the speaker above the listening position
by placing it on a stand or hanging it from the
ceiling. To prevent speaker damage or injury in case
the speaker falls, make sure that it is properly fixed
in place.
Since the active sub woofer does not emit highly
directional signals, you can place it wherever you
want.
Note
Do not place the center speaker further away from the
listening position than the front speakers.
Specifying the speaker
parameters
1 Press MAIN MENU repeatedly to select
SET UP ”.
2 Press or to select the parameter
you want to adjust.
Note
Some speaker settings may appear dimmed in the
display. This means that they have been changed
automatically due to other speaker settings or may
not be adjustable.
Hooking Up and Setting Up the Speaker System
19
US
STR-DE695 4-247-631-11 (1) US
continued
x Surround speaker size
(
SL
SR
XXXXX)
If you connect large speakers that will
effectively reproduce bass frequencies, select
“LARGE”. Normally, select “LARGE”.
However, if the front speakers are set to
“SMALL”, you cannot set the surround
speakers to “LARGE”.
If the sound is distorted, or you feel a lack of
surround effects when using multi channel
surround sound, select “SMALL” to activate
the bass redirection circuitry and output the
surround channel bass frequencies from the sub
woofer or other “LARGE” speakers.
If you do not connect surround speakers, select
“NO”.*
3
Tip
*1–*3 correspond to the following Dolby Pro Logic
modes
*1 NORMAL
*2 PHANTOM
*3 3 STEREO
x Surround back speaker selection
(
S B
XXX)*
If you connect a surround back speaker, select
“YES”.
If you do not connect a surround back speaker,
select “NO”.
* These parameters are not available when “Surround
speaker size (
SL
SR
)” is set to “NO”.
x Front speaker size (
L
R
XXXXX)
If you connect large speakers that will
effectively reproduce bass frequencies, select
“LARGE”. Normally, select “LARGE”.
If the sound is distorted, or you feel a lack of
surround effects when using multi channel
surround sound, select “SMALL” to activate
the bass redirection circuitry and output the
front channel bass frequencies from the sub
woofer.
When the front speakers are set to “SMALL”,
the center and surround speakers are also
automatically set to “SMALL” (unless
previously set to “NO”).
When the sub woofer is set to “NO”, the front
speakers are automatically set to “LARGE” and
you cannot change this setting.
x Center speaker size (
C
XXXXX)
If you connect a large speaker that will
effectively reproduce bass frequencies, select
“LARGE”. Normally, select “LARGE”.
However, if the front speakers are set to
“SMALL”, you cannot set the center speaker to
“LARGE”.
If the sound is distorted, or you feel a lack of
surround effects when using multi channel
surround sound, select “SMALL” to activate
the bass redirection circuitry and output the
center channel bass frequencies from the front
speakers (if set to “LARGE”) or sub woofer.*
1
If you do not connect a center speaker, select
“NO”. The sound of the center channel will be
output from the front speakers.*
2
20
US
STR-DE695 4-247-631-11 (1) US
Multi channel surround setup
(continued)
x Surround back speaker distance
(
S B
DIST. XX ft.)
Set the distance from your listening position to
the surround back speaker. Surround back
speaker distance should be set from a distance
equal to the front speaker distance (A on page
17) to a distance 15 feet closer to your listening
position (D on page 17).
Tip
The receiver allows you to input the speaker position
in terms of distance. However, it is not possible to set
the center speaker further than the front speakers.
Also, the center speaker cannot be set more than
5 feet closer than the front speakers.
Likewise, the surround speakers can not be set farther
away from the listening position than the front
speakers. And they can be no more than 15 feet
closer.
This is because incorrect speaker placement is not
conducive to enjoy surround sound.
Please note that, setting the speaker distance closer
than the actual location of the speakers will cause a
delay in the output of the sound from that speaker. In
other words, the speaker will sound like it is further
away.
For example, setting the center speaker distance
3~6 feet closer than the actual speaker position will
create a fairly realistic sensation of being “inside” the
screen. If you cannot obtain a satisfactory surround
effect because the surround speakers are too close,
setting the surround speaker distance closer (shorter)
than the actual distance will create a larger sound
stage.
Adjusting these parameter while listening to the
sound often results in much better surround sound.
Give it a try!
Tip
Internally, the LARGE and SMALL settings for each
speaker determine whether or not the internal sound
processor will cut the bass signal from that channel.
When the bass is cut from a channel, the bass
redirection circuitry sends the corresponding bass
frequencies to the sub woofer or other “LARGE”
speakers.
However, since bass sounds have a certain amount of
directionality, it is best not to cut them, if possible.
Therefore, even when using small speakers, you can
set them to “LARGE” if you want to output the bass
frequencies from that speaker. On the other hand, if
you are using a large speaker, but prefer not to have
bass frequencies output from that speaker, set it to
“SMALL”.
If the overall sound level is lower than you prefer, set
all speakers to “LARGE”. If there is not enough bass,
you can use the BASS parameter in the EQ menu to
boost the bass levels. To adjust the bass, see page 33.
x Front speaker distance (
L
R
DIST.
XX ft.)
Set the distance from your listening position to
the front speakers (A on page 17).
x Center speaker distance (
C
DIST.
XX ft.)
Set the distance from your listening position to
the center speaker. Center speaker distance
should be set from a distance equal to the front
speaker distance (A on page 17) to a distance
5 feet closer to your listening position (B on
page 17).
x Surround speaker distance (
SL
SR
DIST. XX ft.)
Set the distance from your listening position to
the surround speakers. Surround speaker
distance should be set from a distance equal to
the front speaker distance (A on page 17) to a
distance 15 feet closer to your listening
position (C on page 17).
Hooking Up and Setting Up the Speaker System
21
US
STR-DE695 4-247-631-11 (1) US
60
30
C
D
C
D
45°
90°
20°
B
B
A
A
x Surround speaker placement
(
SL
SR
XXXXXXX)*
This parameter lets you specify the location
and height of your surround speakers for proper
implementation of the Digital Cinema Sound
surround modes. Refer to the illustration below.
Select “SIDE/LO” if the location of your
surround speakers corresponds to section A
and C.
Select “SIDE/HI” if the location of your
surround speakers corresponds to section A
and D.
Select “BEHD/LO” if the location of your
surround speakers corresponds to section B
and C.
Select “BEHD/HI” if the location of your
surround speakers corresponds to section B
and D.
* These parameters are not available when
“Surround speaker size (
SL
SR
)” is set to “NO”.
Tip
The surround speaker placement parameter is
designed specifically for implementation of the
Digital Cinema Sound modes with virtual elements.
With the Digital Cinema Sound modes, speaker
placement is not as critical as other modes. All modes
with virtual elements were designed under the
premise that the surround speaker would be located
behind the listening position, but presentation remains
fairly consistent even with the surround speakers
positioned at a rather wide angle. However, if the
speakers are pointing towards the listener from the
immediate left and right of the listening position, the
sound fields with virtual elements will not be
effective unless the surround speaker placement
parameter is set to “SIDE/LO” or “SIDE/HI”.
Nevertheless, each listening environment has many
variables, like wall reflections, and you may obtain
better results using “BEHD/HI” if your speakers are
located high above the listening position, even if they
are to the immediate left and right.
Therefore, although it may result in a setting contrary
to the “Surround speaker placement” explanation, we
recommend that you playback multi channel surround
encoded software and listen to the effect each setting
has on your listening environment. Choose the setting
that provides a good sense of spaciousness and that
best succeeds in forming a cohesive space between
the surround sound from the surround speakers and
the sound of the front speakers. If you are not sure
which sounds best, select “BEHD/LO” or
“BEHD/HI” and then use the speaker distance
parameter and speaker level adjustments to obtain
proper balance.
continued
22
US
STR-DE695 4-247-631-11 (1) US
Multi channel surround setup
(continued)
Checking the connections
After connecting all of your components to the
receiver, do the following to verify that the
connections were made correctly.
1 Press ?/1 to turn on the receiver.
2 Turn on the component that you
connected (e.g., CD player or tape
deck).
3 Press the input selector button (e.g.,
CD/SACD or MD/TAPE) to select the
component (program source).
4 Start playing.
If you do not obtain normal sound output after
performing this procedure, see
“Troubleshooting” on page 50 and take the
appropriate measures to correct the problem.
Adjusting the speaker level
Use the remote while seated in your listening
position to adjust the level of each speaker.
Note
The receiver incorporates a new test tone with a
frequency centered at 800 Hz for easier speaker level
adjustment.
1 Press ?/1 on the remote to turn on the
receiver.
2 Press TEST TONE on the remote.
You will hear the test tone from each
speaker in sequence.
Front (left) t Center t Front (right) t
Surround (right) t Surround back t
Surround (left) t Sub woofer
3 Adjust the speaker level and balance
using the LEVEL menu so that the level
of the test tone sounds the same from
each speaker.
For details on the LEVEL menu, see page
32.
While adjusting, the test tone is output from
the speaker whose adjustment is performed.
4 Press TEST TONE again to turn off the
test tone.
Tip
You can adjust the level of all speakers at the same
time. Press MASTER VOL +/– on the remote or turn
MASTER VOLUME on the receiver.
Notes
The adjusted value are shown in the display during
adjustment.
Although these adjustments can also be made via
the front panel using the LEVEL menu (when the
test tone is output, the receiver switches to the
LEVEL menu automatically), we recommend you
follow the procedure described above and adjust the
speaker levels from your listening position using the
remote.
24
US
STR-DE695 4-247-631-11 (1) US
MUTING
Press MUTING on the remote to mute the
sound. Press again to cancel the muting
function. The muting function is also canceled
when you turn the power on or turn the
MASTER VOLUME to turn the volume up.
PHONES
Use to connect headphones.
When the headphones are connected, speaker
output is automatically canceled and “SP A”
and “SP B” do not light up in the display.
When the headphones are connected, selectable
sound fields are HP 2CH, HP MULTI or HP
THEA (page 28).
SPEAKERS (OFF/A/B/A+B)
Press SPEAKERS (OFF/A/B/A+B) to output
the sound from the speakers connected to the
SPEAKERS FRONT terminals.
Each time you press the button, the display will
light up cyclically as follows:
SP A t SP B t SP A and SP B t
No display*
To drive Select
Speaker System A SP A (default setting)
(Connected to the
SPEAKERS FRONT A
terminals)
Speaker System B SP B
(Connected to the
SPEAKERS FRONT B
terminals)
Both Speaker System A SP A and SP B
and B (Connected to the
SPEAKERS FRONT A
and B terminals)
* If you do not want to drive Speaker System A
and B, press SPEAKERS (OFF/A/B/A+B) until
“SP A” and “SP B” do not light up in the display
(no display).
Selecting the component (continued)
Changing the display
DIMMER
Press DIMMER repeatedly to adjust the
brightness of the display (3 steps).
DISPLAY
Each time you press DISPLAY, the display
changes cyclically as follows:
Index name of the component* t Selected
component t Sound field applied to the
program source
When the tuner is selected
Index name of the preset station* t
Frequency t Sound field applied to the band
or the preset station
* Index name appears only when you have assigned
one to the component or preset station (page 37).
Index name does not appear when only blank
spaces have been entered, or it is the same as the
input selector.
Enjoying Surround Sound
25
US
STR-DE695 4-247-631-11 (1) US
Enjoying Surround Sound
You can take advantage of surround sound
simply by selecting one of the receiver’s pre-
programmed sound fields. They bring the
exciting and powerful sound of movie theaters
and concert halls into your home. You can also
customize the sound fields to obtain the sound
you want by changing the surround parameter.
To fully enjoy surround sound, you must
register the number and location of your
speakers. See “Multi channel surround setup”
starting from page 17 to set the speaker
parameters before enjoying surround sound.
Using only the front
speakers (2 Channel Stereo)
Press 2CH.
The 2CH indicator lights up and “2CH ST.”
appears in the display.
This mode outputs the sound from the front left
and right speakers only. Standard 2 channel
(stereo) sources completely bypass the sound
field processing. Multi channel surround
formats are downmixed to 2 channel.
Note
No sound is output from the sub woofer when
“2CH ST.” is selected. To listen to 2 channel (stereo)
sources using the front left and right speakers and a
sub woofer, press A.F.D. repeatedly to select
“A.F.D. AUTO”.
Enjoying higher fidelity
sound
The Auto Format Direct (A.F.D.) mode allows
you to select the decoding mode you want for
your audio sound.
Mode Decoding Mode
A.F.D. AUTO As encoded
DOLBY PL Dolby Pro Logic
PLII MOV
Dolby Pro Logic II
PLII MUS
NEO6 CIN
DTS Neo:6
NEO6 MUS
Decoding the input audio
signal automatically
Press A.F.D. repeatedly to select
“A.F.D. AUTO”.
The A.F.D. indicator lights up.
This mode automatically detects the type of
audio signal being input (Dolby Digital, DTS,
or standard 2 channel stereo) and performs the
proper decoding if necessary. This mode
presents the sound as it was recorded/encoded,
without adding any effects (e.g. reverberation).
However, if there are no low frequency signals
(Dolby Digital LFE, etc.) it will generate a low
frequency signal for output to the sub woofer.
continued
26
US
STR-DE695 4-247-631-11 (1) US
Enjoying stereo sound in
multi channel (Dolby Pro
Logic ) and DTS Neo:6
This receiver incorporates with Dolby Pro
Logic II which has movie mode and music
mode, as well as DTS Neo:6 which has cinema
mode and music mode. The receiver can
reproduce 2 channel sound in 5.1 channel
through Dolby Pro Logic II and 6 channels
through DTS Neo:6.
Press A.F.D. repeatedly to select
“DOLBY PL”, “PL MOV”, “PL MUS”,
“NEO6 CIN” or “NEO6 MUS”.
The A.F.D. indicator lights up and the selected
type of decoding is indicated in the display.
x DOLBY PL (Dolby Pro Logic)
Performs the Pro Logic decoding. Software
with multi channel surround audio signals is
played back according to the way it was
recorded. Software with 2 channel audio
signals is decoded with Dolby Pro Logic to
create surround effects (4 channels).
x PL MOV (Pro Logic Movie)
Performs the Pro Logic II movie mode
decoding. This setting is ideal for the movies
encoded in Dolby Surround. Besides, this mode
can reproduce the sound in 5.1 channel when
watching the videos of old movies or in the
dubbed language.
x PL MUS (Pro Logic Music)
Performs the Pro Logic II music mode decoding.
This setting is ideal for the normal stereo
sources, such as CDs.
Note
Dolby Pro Logic and Dolby Pro Logic II decoding
does not function for DTS format signals.
Enjoying higher fidelity sound
(continued)
x NEO6 CIN (DTS Neo:6 Cinema)
Performs the DTS Neo:6 Cinema mode
decoding. This setting is ideal for movies
encoded in DTS Surround.
x NEO6 MUS (DTS Neo:6 Music)
Performs the DTS Neo:6 Music mode decoding.
This setting is ideal for normal stereo sources
such as CDs.
Selecting a sound field
You can enjoy surround sound simply by
selecting one of the pre-programmed sound
fields according to the program you want to
listen to.
Press To select
MOVIE C.ST.EX A DCS
*
C.ST.EX B DCS
*
C.ST.EX C DCS
*
MUSIC HALL
JAZZ
CONCERT
* Sound field with DCS mark use DCS technology.
About DCS (Digital Cinema Sound)
In collaboration with Sony Pictures
Entertainment, Sony measured the sound
environment of their studios and integrated the
data of the measurement and Sony’s own DSP
(Digital Signal Processor) technology to
develop “Digital Cinema Sound”. In a home
theater, “Digital Cinema Sound” simulates an
ideal movie theater sound environment based
on the preference of the movie director.
Enjoying Surround Sound
29
US
STR-DE695 4-247-631-11 (1) US
How to select the surround back decoding mode
You can select the surround back mode you want according to the input stream.
When you select “SB OFF”
Surround back decoding is not performed.
When you select “SB AUTO”
When the input stream contains the 6.1 channel decode flag*
1
, the appropriate decoder is applied to
decode the surround back signal.
For the DTS-ES Matrix 6.1 source, DTS Matrix decoder is applied.
For the DTS-ES Discrete 6.1 source, DTS Discrete decoder is applied to reproduce the Discrete 6.1
channel signal.
Input stream Output channel Applied surround back decoder
Dolby Digital 5.1 5.1
DTS 5.1 5.1
Dolby Digital EX*
2
6.1 Matrix decoder conforms to Dolby Digital EX
DTS-ES Matrix 6.1*
3
6.1 DTS Matrix decoder
DTS-ES Discrete 6.1*
4
6.1 DTS Discrete decoder
When you select “SB MTRX”
Dolby Digital EX is applied to decode the surround back signal regardless of the 6.1 channel decode
flag*
1
in the input stream. This decoder conforms to Dolby Digital EX and functions the same as the
decoders used in movie theaters. This decoder can be used for all the Surround EX formats (Dolby
Digital EX, DTS-ES Matrix 6.1, DTS-ES Discrete 6.1).
Input stream Output channel Applied surround back decoder
Dolby Digital 5.1 6.1 Matrix decoder conforms to Dolby Digital EX
Dolby Digital EX 6.1 Matrix decoder conforms to Dolby Digital EX
DTS 5.1 6.1 Matrix decoder conforms to Dolby Digital EX
DTS-ES Matrix 6.1*
3
6.1 Matrix decoder conforms to Dolby Digital EX
DTS-ES Discrete 6.1*
4
6.1 Matrix decoder conforms to Dolby Digital EX
*
1
6.1 channel decode flag is the information recorded in software like DVDs.
*
2
Dolby Digital DVD that includes a Surround EX flag. The Dolby Corporation web page can help you
distinguish Surround EX films.
*
3
Software encoded with a flag to denote it has both Surround EX and 5.1 channel signals.
*
4
Software encoded with both 5.1 channel signals and an extension stream designed for returning those signals to
6.1 discrete channels. Discrete 6.1 channel signals are DVD specific signals not used in movie theaters.
30
US
STR-DE695 4-247-631-11 (1) US
STEREOD.RANGE EQMULTI CH INCOAXOPT MONO
MEMORY
DIGITAL EXSP BSP A PRO LOGIC II
aa
SLEEP
DTS-ES
LCR
SW
SL SR
SSB
LFE
1234 56 87
9qaqsqdqf
qgqh
NEO:6
0
Understanding the multi channel surround displays
1 SW: Lights up when sub woofer selection is
set to “YES” (page 18) and the audio signal is
output from the SUB WOOFER jacks.
2 SP A*: Lights up when you select to drive
Speaker System A.
3 SP B*: Lights up when you select to drive
Speaker System B.
* Does not light up when you connect
headphones to the PHONES jack.
4 ; DIGITAL EX:; DIGITAL” lights up
when the receiver is decoding signals
recorded in the Dolby Digital format.
; DIGITAL EX” lights up when the
receiver is decoding signals recorded in the
Dolby Digital EX format.
5 ; PRO LOGIC II:; PRO LOGIC”
lights up when the receiver applies Pro Logic
processing to 2 channel signals in order to
output the center and surround channel
signals. “; PRO LOGIC II” lights up when
Pro Logic II processing (“PLII MOV” or
“PLII MUS”) is applied (page 26). However,
both indicators do not light up if the center
and surround speakers are set to “NO”, and
“A.F.D. AUTO”, “DOLBY PL”, “PLII
MOV” or “PLII MUS” is selected.
Note
Dolby Pro Logic and Dolby Pro Logic II
decoding does not function for DTS format
signals.
6 DTS-ES: “DTS” lights up when DTS signals
are input. “DTS-ES” lights up when DTS-ES
signals are input.
Note
When playing a DTS format disc, be sure that
you have made digital connections and that
INPUT MODE is NOT set to “ANALOG”
(page 23).
7 NEO:6: Lights up when DTS Neo:6
processing (“NEO6 CIN” or “NEO6 MUS”)
is applied.
8 Tuner indicators: Lights up when using the
receiver to tune in radio stations, etc. See
pages 34–36 for tuner operations.
9 SLEEP: Lights up when sleep timer is
activated.
0 EQ: Lights up when the equalizer functions.
qa D.RANGE: Lights up when dynamic range
compression is activated. See page 32 to
adjust the dynamic range compression.
qs MULTI CH IN: Lights up when MULTI CH
IN is selected.
Enjoying Surround Sound
31
US
STR-DE695 4-247-631-11 (1) US
qd COAX: Lights up when the source signal is a
digital signal being input through the
COAXIAL terminal.
qf OPT: Lights up when the source signal is a
digital signal being input through the
OPTICAL terminal.
qg LFE: Lights up when the disc being played
back contains the LFE (Low Frequency
Effect) channel and when the sound of the
LFE channel signal is actually being
reproduced.
qh Playback channel indicators: The letters
(L, C, R, etc.) indicate the channels being
played back. The boxes around the letters
vary to show how the receiver downmixes the
source sound (based on the speakers settings).
When using sound fields like “C.ST.EX”, the
receiver adds reverberation based on the
source sound.
L (Front Left), R (Front Right), C (Center
(monaural)), SL (Surround Left), SR
(Surround Right), S (Surround (monaural or
the surround components obtained by Pro
Logic processing)), SB (Surround Back (the
surround back components obtained by 6.1
matrix decoding)).
Example:
Recording format (Front/Surround): 3/2
Output channel: Surround speakers absent
Sound Field: A.F.D. AUTO
Customizing sound fields
By adjusting the surround parameters and the
equalization of the front speakers, you can
customize the sound fields to suit your
particular listening situation.
Once you customize a sound field, the changes
are stored in the memory indefinitely. You can
change a customized sound field any time by
making new adjustments to the parameters.
See the tables on pages 57–58 for the
parameters available in each sound field.
To get the most from multi
channel surround sound
Position your speakers and do the procedures
described in “Multi channel surround setup”
starting from page 17 before you customize a
sound field.
Note on the displayed items
The setup items you can adjust in each menu
vary depending on the sound field. Certain
setup parameters may be dimmed in the
display. This means that the selected parameter
is either unavailable or fixed and unchangeable.
SL SR
L
C R
continued
32
US
STR-DE695 4-247-631-11 (1) US
Customizing sound fields (continued)
Front balance (
L
R
BAL. L/R XX)
Lets you adjust the balance between front left
and right speakers.
Center level (CTR XXX.X dB)
Lets you adjust the level of the center speaker.
Surround left level (SUR.L. XXX.X
dB)
Lets you adjust the level of the surround left
speaker.
Surround right level (SUR.R. XXX.X
dB)
Lets you adjust the level of the surround right
speaker.
Surround back level (SB XXX.X dB)
Lets you adjust the level of the surround back
speaker.
Sub woofer level (S.W. XXX.X dB)
Lets you adjust the level of the sub woofer.
Dynamic range compressor (
D. RANGE
COMP. XXX)
Lets you compress the dynamic range of the
sound track. This may be useful when you want
to watch movies at low volumes late at night.
We recommend using the “MAX” setting.
To reproduce the sound track with no
compression, select “OFF”.
To reproduce the sound track with the dynamic
range intended by the recording engineer, select
“STD”.
To reproduce a dramatic compression of the
dynamic range, select “MAX”.
Note
Dynamic range compression is possible with Dolby
Digital sources only.
Effect level (EFCT. XXX)
Lets you adjust the “presence” of the current
surround effect.
Adjusting the level
parameters
The LEVEL menu contains parameters that let
you adjust the balance and volumes of each
speaker. You can also customize various
aspects of the current sound field. The settings
are applied to all sound fields except for EFCT.
parameter. For EFCT. parameter, the settings
are stored individually for each sound field.
1 Start playing a program source
encoded with multi channel surround
sound.
2 Press MAIN MENU repeatedly to select
LEVEL .
3 Press or to select the parameter
you want to adjust.
4 Turn the jog dial to select the setting
you want.
The setting is entered automatically.
Initial settings
Parameter Initial setting
L
R
BAL. L/R XX BALANCE
CTR XXX.X dB 0 dB
SUR.L. XXX.X dB 0 dB
SUR.R. XXX.X dB 0 dB
SB XXX.X dB 0 dB
S.W. XXX.X dB 0 dB
D. RANGE
COMP. XXX OFF
EFCT. XXX STD
Enjoying Surround Sound
33
US
STR-DE695 4-247-631-11 (1) US
Bass (BASS XXX.X dB)
Lets you adjust the gain of bass.
Treble (TREB. XXX.X dB)
Lets you adjust the gain of treble.
Resetting customized sound
fields to the factory settings
1 If the power is on, press ?/1 to turn off
the power.
2 Hold down 2CH and press ?/1.
“SF. CLR.” appears in the display and all
sound fields are reset at once.
Adjusting the equalizer
parameter
The EQ menu contains parameters that let you
adjust the equalizer of the front speakers for
optimum sound. The settings are applied to all
sound fields.
1 Start playing a program source
encoded with multi channel surround
sound.
2 Press MAIN MENU repeatedly to select
EQ .
3 Press or to select the parameter
you want to adjust.
4 Turn the jog dial to select the setting
you want.
The setting is entered automatically.
Initial settings
Parameter Initial setting
BASS XXX.X dB 0 dB
TREB. XXX.X dB 0 dB
EQ XXX OFF
To turn on/off the equalizer
1 Press MAIN MENU repeatedly to select
EQ .
2 Press or repeatedly to select
EQ XXX.
3 Turn the jog dial to select EQ ON or
EQ OFF.
Note
The EQ indicator in the display lights up when the
equalizer is turned on. When you adjust the equalizer
using the EQ parameters, the settings are applied to
all sound fields and can be reproduced whenever you
turn on the equalizer.
34
US
STR-DE695 4-247-631-11 (1) US
4 If you’ve tuned in an AM station, adjust
the direction of the AM loop antenna for
optimum reception.
5 Repeat steps 1 to 4 to receive another
station.
Tips
If you do not remember the precise frequency, press
TUNING + or TUNING – after entering the value
close to the frequency you want. The receiver
automatically tunes in the station you want. If the
frequency seems to be higher than the entered
value, press TUNING +, and if the frequency seems
to be lower than the entered value, press
TUNING –.
If “STEREO” flashes in the display and the FM
stereo reception is poor, press FM MODE to change
to monaural (MONO). You will not be able to enjoy
the stereo effect, but the sound will be less
distorted. To return to stereo mode, press
FM MODE again.
The tuning scale differs depending on the area code
as shown in the following table. For details on area
codes, see page 4.
Area code FM AM
U, CA 100 kHz 10 kHz*
* The AM tuning scale can be changed (page 54).
Receiving Broadcasts
bbbb
1 0 2 5 0
bbb
1 3 5 0
Before receiving broadcasts, make sure you
have connected FM and AM antennas to the
receiver (page 7).
Direct tuning
You can enter a frequency of the station you
want directly by using the numeric buttons on
the supplied remote. For details on the buttons
used in this section, see pages 42–49.
1 Press TUNER on the remote repeatedly
to select the FM or AM band.
The last received station is tuned in.
2 Press D. TUNING on the remote.
3 Press the numeric buttons to enter the
frequency.
Example 1: FM 102.50 MHz
Example 2: AM 1350 kHz
(You don’t have to enter the last “0” when the
tuning scale is set to 10 kHz.)
If you cannot tune in a station and the
entered numbers flash
Make sure you’ve entered the right
frequency. If not, repeat steps 2 and 3.
If the entered numbers still flash, the
frequency is not used in your area.
Receiving Broadcasts
35
US
STR-DE695 4-247-631-11 (1) US
Automatic tuning
If you don’t know the frequency of the station
you want, you can let the receiver scan all
available stations in your area.
1 Press TUNER FM/AM repeatedly to
select the FM or AM band.
The last received station is tuned in.
2 Press TUNING + or TUNING –.
Press TUNING + to scan from low to high;
press TUNING – to scan from high to low.
The receiver stops scanning whenever a
station is received.
When the receiver reaches either end of
the band
Scanning is repeated in the same direction.
3 To continue scanning, press TUNING +
or TUNING – again.
Preset tuning
After you have tuned in stations using Direct
Tuning or Automatic Tuning, you can preset
them to the receiver. Then you can tune in any
of the stations directly by entering its
2-character preset code using the supplied
remote. Up to 30 FM or AM stations can be
preset. The receiver will also scan all the
stations that you have preset.
Before tuning to preset stations, be sure to
preset them by performing steps on “Presetting
radio stations”.
continued
Presetting radio stations
1 Press TUNER FM/AM.
The last received station is tuned in.
2 Tune in the station that you want to
preset using Direct Tuning (page 34) or
Automatic Tuning (page 35).
3 Press MEMORY.
“MEMORY” appears in the display for a
few seconds.
Do steps 4 to 5 before “MEMORY” goes
out.
4 Press PRESET TUNING + or PRESET
TUNING – repeatedly to select a preset
station number.
Each time you press the button, the preset
station number changes in the
corresponding number and direction as
follows:
If “MEMORY” goes out before you press
the preset station number, start again from
step 3.
5 Press MEMORY again to store the
station.
If “MEMORY” goes out before you can
store the station, start again from step 3.
6 Repeat steps 2 to 5 to preset another
station.
To change a preset number to
another station
Do steps 1 to 5 to preset a new station to the
number.
Tip
In Step 4, you can also use the remote to select a
preset station number. Press SHIFT repeatedly to
select a memory page (A, B or C) and then press the
numeric button to select a preset number.
nA1˜A2˜...˜A0˜B1˜B2˜...˜B0N
nC0˜...C2˜C1N
36
US
STR-DE695 4-247-631-11 (1) US
nA1˜A2˜...˜A0˜B1˜B2˜...˜B0N
nC0˜...C2˜C1N
Tuning to preset stations
You can tune the preset stations by either of the
following two ways.
Scanning the preset stations
1 Press TUNER FM/AM.
The last received station is tuned in.
2 Press PRESET TUNING + or PRESET
TUNING – repeatedly to select the
preset station you want.
Each time you press the button, the receiver
tunes in one preset station at a time, in the
corresponding order and direction as
follows:
Using the preset codes
Use the supplied remote to perform the
following operations. For details on the buttons
used in this section, see pages 42–49.
1 Press TUNER on the remote.
The last received station is tuned in.
2 Press SHIFT to select a memory page
(A, B, or C), then press the preset
number of the station you want using
the numeric buttons.
Preset tuning (continued)
Other Operations
37
US
STR-DE695 4-247-631-11 (1) US
Other Operations
To insert a space
Turn the jog dial until a blank space appears
in the display.
If you’ve made a mistake
Press or repeatedly until the character
to be changed flashes, then turn the jog dial
to select the character you want.
5 Press ENTER.
6 Repeat steps 2 to 5 to assign index
name for another station or program
source.
Recording
Before you begin, make sure you’ve connected
all components properly.
Recording on an audio tape
or MiniDisc
You can record on a cassette tape or MiniDisc
using the receiver. See the operating
instructions of your cassette deck or MD deck
if you need help.
1 Select the component to be recorded.
2 Prepare the component for playing.
For example, insert a CD into the CD
player.
3 Insert a blank tape or MD into the
recording deck and adjust the
recording level, if necessary.
4 Start recording on the recording deck,
then start playback on the playback
component.
Naming preset stations
and program sources
You can enter a name (index name) of up to 8
characters for preset stations and program
sources. These names (for example, “VHS”)
appear in the receiver’s display when a station
or program source is selected. Note that no
more than one name can be entered for each
preset station or program source.
This function is useful for distinguishing
components of the same kind. For example,
two VCRs can be specified as “VHS” and
“8MM”, respectively. It is also handy for
identifying components connected to jacks
meant for another type of component, for
example, a second CD player connected to the
MD/TAPE jacks.
1 To name a preset station
Press TUNER FM/AM, then tune in the
preset station you want to create an
index name for.
If you are not familiar with how to tune in
preset stations, see “Tuning to preset
stations” on page 36.
To name a program source
Select the program source (component)
to be named.
2 Press MAIN MENU repeatedly to select
CUSTOM ”.
3 Press or repeatedly to select
“NAME IN”.
4 Create an index name by using the jog
dial and or :
Turn the jog dial to select a character, then
press to move the cursor to the next
position.
continued
Other Operations
39
US
STR-DE695 4-247-631-11 (1) US
AUTO mode (DEC. AUTO)
Use to enjoy playback from audio CD
(PCM), DVD, DTS-CD and DTS-LD
sources. However, with audio CDs, you may
not be able to listen the very first moments
of each track.
Normally, use as-is with the initial settings
above.
x CONTROL A1 power save function
(P.SAVE.XXX)
When set to “OFF”, you can turn on the
receiver automatically when the component
connected via monaural miniplug cord (see
page 13) is turned on and the playback is
started. However, the receiver will not be
turned on automatically if set to “ON”.
When set to “ON”, you can save the power
consumption of the receiver during standby
mode.
Changing the command
mode of the receiver
This function is useful when you use 2 Sony
receivers in the same room.
1 Turn off the receiver.
2 Hold down ENTER and press ?/1 to
turn on the receiver.
“C.MODE.AVX” appears in the display.
Each time you repeat the procedure above,
the display changes as follows:
C.MODE.AV1 y C.MODE.AV2
Tip
The initial setting is “C.MODE.AV2”.
Notes
The initial setting for the command mode of the
supplied remote is “AV2”.
If the command mode of the receiver and the
remote is different, you cannot use the remote to
operate the receiver.
Adjustments using the
CUSTOM menu
The CUSTOM menu allows you to make the
following adjustments.
1 Press MAIN MENU repeatedly to select
CUSTOM .
2 Press or to select the parameter
you want to adjust.
Certain setup parameters may be dimmed in
the display. This means that the selected
parameter is either unavailale or fixed and
unchangeable due to sound field (pages 25–
28) or other settings.
3 Turn the jog dial to select the setting
you want.
The setting is entered automatically.
4 Repeat steps 2 and 3 until you have set
all of the parameters that follow.
Initial settings
Parameter Initial setting
SB XXXX AUTO
DEC. XXXX PCM (for DVD,
CD/SACD and MD/TAPE),
AUTO (for VIDEO 2)
P.SAVE.XXX OFF
x Surround back decoding mode
(SB XXXX)
You can also set this parameter using SURR
BACK DECODING on the front panel. For
details, see page 28.
x Decode priority (DEC. XXXX)
Sets the appropriate decoding for incoming
digital signals.
PCM priority mode (DEC. PCM)
Use to enjoy playback from audio CD
(PCM), DVD and MD. When used with
media other than CD, DVD or MD, you may
experience noise and “DEC. ERR.” appears
in the display. If this happens, switch to
AUTO mode.
40
US
STR-DE695 4-247-631-11 (1) US
CONTROL A1 control
system
Getting Started
This section explains the basic functions
of the CONTROL A1 Control System.
Certain components have special
functions, such as CD Synchro Dubbing
on cassette decks, that require CONTROL
A1 connections. For detailed information
regarding specific operations, be sure to
also refer to the Operating Instructions
supplied with your component(s).
The CONTROL A1II Control System was
designed to simplify the operation of audio
systems composed of separate Sony
components. CONTROL A1II connections
provide a path for the transmission of control
signals which enable automatic operation and
control features usually associated with
integrated systems.
Currently, CONTROL A1II connections
between a Sony CD player, amplifier
(receiver), MD deck and cassette deck provide
automatic function selection and synchronized
recording.
In the future, the CONTROL A1II connection
will work as a multifunction bus allowing you
to control various functions for each
component.
Notes
The CONTROL A1II Control System is designed to
maintain upward compatibility as the Control
System is upgraded to handle new functions. In this
case, however, older components will not be
compatible with the new functions.
Do not operate a 2 way remote control unit when
the CONTROL A1II jacks are connected via a PC
interface kit to a personal computer running “MD
Editor” or similar application. Also, do not operate
the connected component in a manner contrary to
the functions of the application, as this may cause
the application to operate incorrectly.
Example
Amplifier
(Receiver)
CD
player
MD
deck
Tape
deck
Other
component
CONTROL A1 and CONTROL A1
compatibility
The CONTROL A1 control system has been
updated to the CONTROL A1II which is the
standard system in the Sony 300 disc CD changer
and other recent Sony components. Components
with CONTROL A1 jacks are compatible with
components with CONTROL A1II, and can be
connected to each other. Basically, the majority of
the functions available with the CONTROL A1
control system will be available with the
CONTROL A1II control system.
However, when making connections between
components with CONTROL A1 jacks and
components with CONTROL A1II jacks, the
number of functions that can be controlled may be
limited depending on the component. For detailed
information, refer to the operating instructions
supplied with the component(s).
Connections
Connect monaural mini-plug cords in series to
the CONTROL A1II jacks on the back of each
component. You can connect up to 10
CONTROL A1II compatible components in
any order. However, you can connect only one
of each type of component (i.e., 1 CD player, 1
MD deck, 1 tape deck and 1 receiver).
(You may be able to connect more than one CD
player or MD deck, depending on the model.
Refer to the operating instructions supplied
with the respective component for details.)
Other Operations
41
US
STR-DE695 4-247-631-11 (1) US
Automatic function selection
When you connect a CONTROL A1II
compatible Sony amplifier (or receiver) to
other Sony components using monaural mini-
plug cords, the function selector on the
amplifier (or receiver) automatically switches
to the correct input when you press the play
button on one of the connected components.
Notes
You must connect a CONTROL A1 compatible
amplifier (receiver) using a monaural mini-plug
cord in order to take advantage of the automatic
function selection feature.
This function only works when the components are
connected to the amplifier (or receiver) inputs
according to the names on the function buttons.
Certain receivers allow you to switch the names of
the function buttons. In this case, refer to the
operating instructions supplied with the receiver.
When recording, do not play any components other
than the recording source. It will cause the
automatic function selection to operate.
Synchronized recording
This function lets you conduct synchronized
recording between the selected source and
recorder components.
1 Set the function selector on the
amplifier (or receiver) to the source
component.
2 Set the source component to pause
mode (make sure both the N and X
indicators light together).
3 Set the recorder component to the
REC-PAUSE mode.
4 Press PAUSE on the recorder
component.
The source component is released from
the pause mode, and recording begins
shortly thereafter.
When playback ends from the source
component, recording stops.
Notes
Do not set more than one component to the pause
mode.
Certain recorder components may be equipped with
a special synchronized recording function that uses
the CONTROL A1II Control System, such as
“CD Synchro Dubbing”. In this case, refer to the
operating instructions supplied with the recorder
component.
CONTROL A1
Jacks and connection examples
CONTROL A1
CD player
MD deck
In the CONTROL A1II control system, the
control signals flow both ways, so there is no
distinction of IN and OUT jacks. If a
component has more than one CONTROL A1II
jack, you can use either one, or connect
different components to each jack.
On CONTROL A1 jacks and
connections
It is possible to make connections between
CONTROL A1 and CONTROL A1II jacks.
For details regarding particular connections or
set up options, refer to the operating
instructions supplied with the component(s).
About the connecting cord
Some CONTROL A1 compatible components
are supplied with a connecting cord as an
accessory. In this case, use the connecting cord
for your connection.
When using a commercially available cord, use
a monaural mini-plug cord less than 2 meters
long, with no resistance (such as the Sony
RK-G69HG).
Basic Functions
The CONTROL A1II functions will operate as
long as the component you want to operate is
turned on, even if all of the other connected
components are not turned on.
42
US
STR-DE695 4-247-631-11 (1) US
You can use the remote RM-PP412 to operate
the components in your system.
Before you use your
remote
Inserting batteries into the
remote
Insert R6 (size-AA) batteries with the + and –
properly oriented in the battery compartment.
When using the remote, point it at the remote
sensor g on the receiver.
Tip
Under normal conditions, the batteries should last for
about 6 months. When the remote no longer operates
the receiver, replace all batteries with new ones.
Notes
Do not leave the remote in an extremely hot or
humid place.
Do not use a new battery with an old one.
Do not expose the remote sensor to direct sunlight
or lighting apparatuses. Doing so may cause a
malfunction.
If you don’t use the remote for an extended period
of time, remove the batteries to avoid possible
damage from battery leakage and corrosion.
Remote button
description
H
X
m
M
.
>
-
VIDEO1 VIDEO2
USE MODE
SYSTEM STANDBY
SLEEP
AV1 AV2
TV ?/1 AV ?/1
VIDEO3 DVD
TV/SAT
MD/TAPE CD/SACD
TUNER
PHONO AUX
MULTI CH SOURCE
SHIFT
TOP MENU/
GUIDE
AV MENU
MUTING
MASTER
VOL
DISPLAY
TV VOL TV CH
WIDE ON SCREEN
TV/
VIDEO
MAIN
MENU
RETURN/EXIT
D.TUNING DISC ALT
ANT
CLEAR
SEARCH MODE
2CH
A.F.D.
123
456
789
0/10 >10/11 12
MOVIE
SUBTITLE ENTER
MUSIC
AUDIO
SWAP/
ANGLE
JUMP/
TIME
PRESET/
CH/D.SKIP
TEST
TONE
SB
DECODINGDIRECT
AAC
BI-LING
x
?/1
P
O
f
F
G
g
Operations Using the Remote RM-PP412
The tables below show the settings of each
button.
Remote Operations Function
Button
?/1 Receiver
Turns the receiver on or off.
SLEEP Receiver Activates the sleep
function and the duration
which the receiver turns
off automatically.
ENTER/
EXECUTE
Operations Using the Remote RM-PP412
43
US
STR-DE695 4-247-631-11 (1) US
Remote Operations Function
Button
VIDEO1 Receiver To watch VCR.
(VTR mode 3)
VIDEO2 Receiver To watch VCR.
(VTR mode 1)
VIDEO3 Receiver To watch VCR.
(VTR mode 2)
DVD Receiver To watch DVD.
TV/SAT Receiver To watch TV programs
or satellite receiver.
MD/TAPE Receiver To listen to Minidisc or
audio tape.
CD/SACD Receiver To listen to compact
disc.
TUNER Receiver To listen to radio
programs.
PHONO Receiver To listen to turntable.
AUX Receiver To listen to an audio
equipment.
MULTI CH
Receiver Selects MULTI CH IN
source.
2CH Receiver Selects 2CH mode.
A.F.D. Receiver Selects A.F.D. AUTO,
DOLBY PL, PLII MOV,
PLII MUS, NEO6 CIN
and NEO6 MUS.
MOVIE Receiver Selects C.ST.EX A,
C.ST.EX B and
C.ST.EX C.
MUSIC Receiver Selects HALL, JAZZ
and CONCERT.
TEST Receiver Press to output test tone.
TONE
DIRECT Receiver Selects 2CH ANALOG
DIRECT.
AAC Receiver Selects Dual Mono or
BI-LING Bilingual sound of
Dolby Digital, DTS or
AAC, etc.
SB Receiver Press to select the
DECODING surround back decoding
modes.
Remote Operations Function
Button
SHIFT Receiver Press repeatedly to
select a memory page
for presetting radio
stations or tuning to
preset stations.
D.TUNING Receiver Tuner station direct key-
in-mode.
MUTING Receiver Mutes the sound from
the receiver.
V/v Receiver Select a menu item.
B/b Receiver Makes adjustment or
change the setting.
MASTER Receiver Adjusts the master
VOL +/– volume of the receiver.
MAIN Receiver Press this button
MENU repeatedly to select one
of the four cursor
modes: SET UP,
LEVEL, EQ and
CUSTOM.
ON Receiver To display the menus
SCREEN of the receiver on the
TV screen.
AV ?/1 TV/VCR/ Turns the audio and
CD player/ video components on or
VCD player/ off.
LD player/
DVD player/
MD deck/
DAT deck
SYSTEM Receiver/ Turns off the receiver
STANDBY TV/VCR/ and other Sony audio/
(Press Satellite tuner/ video components.
AV ?/1 CD player/
and ?/1 VCD player/
at the LD player/
same time) DVD player/
MD deck/
DAT deck
continued
44
US
STR-DE695 4-247-631-11 (1) US
Remote Button Description
(continued)
Remote Operations Function
Button
1–9 and Receiver Use with “SHIFT” button
0/10 to preset radio station or
tuning to preset stations
and with “D.TUNING”
for direct tuning.
CD player/ Select track numbers.
VCD player/ 0/10 selects track 10.
LD player/
MD deck/
DAT deck
TV/VCR/ Select channel numbers.
Satellite tuner
>10/11 CD player/ Select track numbers
VCD player/ over 10.
LD player/
MD deck/
Tape deck
AUDIO TV/ VCR/ Changes the sound to
DVD player Multiplex, Bilingual or
Multi channel TV Sound.
SWAP*/ TV Swaps the small and
ANGLE large picture.
DVD player To select viewing angle
or changes the angles.
JUMP/ TV Toggles between the
TIME previous and the current
channels.
CD player/ Shows the time or
VCD player/ displays the playing time
DVD player of disc, etc.
* Only for Sony TVs with the picture-in-picture
function.
Remote Operations Function
Button
PRESET/ Receiver Scans and selects preset
CH/ stations.
D.SKIP +/– TV/VCR/ Selects preset channels.
satellite tuner
CD player/ Skips discs (multi-disc
VCD player/ changer only).
DVD player/
MD deck
ENTER TV/VCR/ After selecting a
satellite tuner/ channel, disc or track
LD player/ using the numeric
MD deck/ buttons, press to enter
DAT deck/ the value.
Tape deck
DISC CD player/ Selects a disc directly
VCD player (multi-disc changer
only).
ANT VCR Selects output signal
from aerial terminal: TV
signal or VCR program.
./> VCR/ Skips tracks.
CD player/
VCD player/
DVD player/
LD player/
MD deck/
DAT deck/
Tape deck
m/M CD player/ Searches tracks
VCD player/ (forward or backward).
DVD player/
LD player/
MD deck
VCR/ Fastforwards or
DAT deck/ rewinds.
Tape deck
Operations Using the Remote RM-PP412
45
US
STR-DE695 4-247-631-11 (1) US
Remote Operations Function
Button
N VCR/ Starts play.
CD player/
VCD player/
LD player/
DVD player/
MD deck/
DAT deck/
Tape deck
X VCR/ Pauses play or record.
CD player/ (Also starts recording
VCD player/ with components in
LD player/ record standby.)
DVD player/
MD deck/
DAT deck/
Tape deck
x VCR/ Stops play.
CD player/
VCD player/
LD player/
DVD player/
MD deck/
DAT deck/
Tape deck
DISPLAY TV/VCR/ Selects information
VCD player/ displayed on the TV
LD player/ screen.
DVD player
RETURN/ VCD player/ Returns to the previous
EXIT LD player/ menu.
DVD player
Satellite tuner Exits the menu.
SUBTITLE DVD player Changes the subtitles.
CLEAR DVD player Press if you made a
mistake when you press
the number button or
press to return to the
continuous play etc.
Remote Operations Function
Button
SEARCH DVD player Select searching mode.
MODE Press to select the unit
for search (track,
index, etc.)
TOP MENU/ DVD player Displays DVD title.
GUIDE
satellite tuner Displays guide menu.
AV MENU VCR/ Displays menu.
Satellite tuner/
DVD player
O VCD player/ Returns to the previous
LD player/ menu or exits the
DVD player menu.
V/v/B/b VCR/ Selects a menu item.
Satellite tuner/
DVD player
ENTER/ VCR/ Press to enter the
EXECUTE Satellite tuner/ selection.
DVD player
TV ?/1 TV Turns the TV on or off.
-/-- TV Selects the channel
entry mode, either one
or two digit.
TV VOL TV Adjust the volume of
+/– the TV.
TV CH +/– TV Select preset TV
channels.
TV/ TV Selects input signal:
VIDEO TV input or video
input.
WIDE TV Selects the wide
picture mode.
USE MODE Remote To set up the remote.
AV1 and Remote Select the command
AV2 mode of the remote.
SOURCE Remote Selects 2ND AV
output.
ALT Remote Change remote key
function to activate
those buttons with
orange printing.
continued
46
US
STR-DE695 4-247-631-11 (1) US
Notes
Some functions explained in this section may not
work depending on the model of the receiver.
The above explanation is intended to serve as an
example only. Therefore, depending on the
component the above operation may not be possible
or may operate differently than described.
To activate the buttons with orange printing, press
ALT first before pressing the buttons.
Press MAIN MENU on the remote before you use
the V/v/B/b buttons for receiver operation.
Press TOP MENU/GUIDE or AV MENU on the
remote before you use the remote to control the
satellite tuner, VCR and DVD player.
The TV/SAT, PHONO, SOURCE, DIRECT, AAC
BI-LING, 12 and ON SCREEN functions are not
available for set operation.
Selecting the command
mode of the remote
Set the remote command mode using the USE
MODE button and the remote command mode
buttons.
Selecting the command mode
You can switch the command mode (AV1 or
AV2) of the remote. If the command mode of
the receiver and the remote is different, you
cannot use the remote to operate the receiver.
Press AV1 or AV2 while pressing down
USE MODE.
The indicator lights once (twice for AV2) , then
the command mode switches.
To check the command mode of the
remote
Press USE MODE. You can check the remote
by the indicator.
Mode Indicator lights
AV1 once
AV2 twice
Remote Button Description
(continued)
To reset the remote to factory
settings
Press =/1, AV =/1, and MASTER VOL – at
the same time.
The indicator lights 3 times, then goes off.
Programming the remote
You can program the remote to control non-
Sony components by changing the code. Once
the control signals have been memorized, you
can use those components as part of your
system.
Furthermore, you can also program the remote
for Sony components that the remote is unable
to control. Note that the remote can only
control components that accept infrared
wireless control signals.
1 Press AV ?/1 while pressing down USE
MODE.
The indicator lights.
2 Press the input selector button
(including TV ?/1) for the component
you want to control.
For example, if you are going to control a
CD player, press CD/SACD.
3 Press the numeric buttons to enter the
numeric code (or one of the codes if
more than one code exists)
corresponding to the component and
the maker of the component you want
to control.
See the tables on pages 47–49 for
information on the numeric code(s)
corresponding to the component and the
maker of the component (the first digit and
the last two digits of the numeric code
correspond to the category and the maker’s
code respectively.)
4 Press ENTER.
Once the numeric code has been verified,
the indicator slowly flashes twice and the
remote automatically exits the programming
mode.
Operations Using the Remote RM-PP412
47
US
STR-DE695 4-247-631-11 (1) US
The numeric codes corresponding to
the component and the maker of the
component
Use the numeric codes in the tables below to
control non-Sony components and also Sony
components that the remote is normally unable
to control. Since the remote signal that a
component accepts differs depending on the
model and year of the component, more than
one numeric code may be assigned to a
component. If you fail to program your remote
using one of the codes, try using other codes.
Notes
The numeric codes are based on the latest
information available for each brand. There is a
chance, however, that your component will not
respond to some or all of the codes.
All of the input selectors on this remote may not be
available when used with your particular
component.
To control a CD player
Maker Code(s)
SONY 101, 102, 103
DENON 104, 123
JVC 105, 106, 107
KENWOOD 108, 109, 110
MAGNAVOX 111, 116
MARANTZ 116
ONKYO 112, 113, 114
PANASONIC 115
PHILIPS 116
PIONEER 117
TECHNICS 115, 118, 119
YAMAHA 120, 121, 122
continued
5 Repeat steps 1 to 4 to control other
components.
To cancel programming
Press USE MODE during any step. The remote
automatically exits the programming mode.
To activate the input source after
programming
Press the programmed button to activate the
input source you want.
If programming is unsuccessful,
check the following:
If the indicator does not light up in step 1, the
batteries are weak. Replace both batteries.
If the indicator flashes 4 times in quick succession
while entering the numeric code, an error has
occurred. Start again from step 1.
Notes
The indicator turns off while a valid button is
pressed.
In step 2, if several input selector buttons are
pressed, only the last pressed button is valid.
In step 2, if you press TV ?/1, only TV VOL +/–,
TV CH +/–, TV/VIDEO and WIDE buttons are
reprogrammed.
In step 3, if an input selector button is pressed, the
new input source is selected and the programming
procedure returns to the beginning of step 3.
For the numeric codes, only the first three numbers
entered are valid.
To clear the memory of the remote
To clear all programmed and learned signals,
do the following to reset the remote to factory
settings.
Press ?/1, AV ?/1 and MASTER VOL – at
the same time.
The indicator flashes 3 times, then goes off.
48
US
STR-DE695 4-247-631-11 (1) US
Programming the remote (continued)
To control a DAT deck
Maker Code(s)
SONY 203
PIONEER 219
To control an MD deck
Maker Code(s)
SONY 301
DENON 302
JVC 303
KENWOOD 304
To control a tape deck
Maker Code(s)
SONY 201, 202
DENON 204, 205
KENWOOD 206, 207, 208, 209
NAKAMICHI 210
PANASONIC 216
PHILIPS 211, 212
PIONEER 213, 214
TECHNICS 215, 216
YAMAHA 217, 218
To control an LD player
Maker Code(s)
SONY 601, 602, 603
PIONEER 606
To control a video CD player
Maker Code(s)
SONY 605
To control a VCR
Maker Code(s)
SONY 701, 702, 703, 704, 705,
706
AIWA 710, 750, 757, 758
AKAI 707, 708, 709, 759
BLAUPUNKT 740
EMERSON 711, 712, 713, 714, 715,
716, 750
FISHER 717, 718, 719, 720
GENERAL ELECTRIC 721, 722, 730
GOLDSTAR 723, 753
GRUNDIG 724
HITACHI 722, 725, 729, 741
ITT/NOKIA 717
JVC 726, 727, 728, 736
MAGNAVOX 730, 731, 738
MITSUBISHI/MGA 732, 733, 734, 735
NEC 736
PANASONIC 729, 730, 737, 738, 739,
740
PHILIPS 729, 730, 731
PIONEER 729
RCA/PROSCAN 722, 729, 730, 731, 741,
747
SAMSUNG 742, 743, 744, 745
SANYO 717, 720, 746
SHARP 748, 749
TELEFUNKEN 751, 752
TOSHIBA 747, 755, 756
ZENITH 754
To control a DVD player
Maker Code(s)
SONY 401, 402, 403
PANASONIC 406, 408
PHILIPS 407
PIONEER 409
TOSHIBA 404
DENON 405
Operations Using the Remote RM-PP412
49
US
STR-DE695 4-247-631-11 (1) US
To control a TV
Maker Code(s)
SONY 501, 502
DAEWOO 504, 505, 506, 507, 515,
544
FISHER 508
GOLDSTAR 503, 511, 512, 515, 534,
544
GRUNDIG 517, 534
HITACHI 513, 514, 515, 544
ITT/NOKIA 521, 522
JVC 516
MAGNAVOX 503, 518, 544
MITSUBISHI/MGA 503, 519, 544
NEC 503, 520, 544
PANASONIC 509, 524
PHILIPS 515, 518
PIONEER 509, 525, 526, 540
RCA/PROSCAN 510, 527, 528, 529, 544
SAMSUNG 503, 515, 531, 532, 533,
534, 544
SANYO 508, 545, 546, 547
SHARP 535
TELEFUNKEN 523, 536, 537, 538
THOMSON 530, 537, 539
TOSHIBA 535, 540, 541
ZENITH 542, 543
To control a satellite tuner or cable
box
Maker Code(s)
SONY 801, 802, 803, 804
JERROLD/G.I. 806, 807, 808, 809, 810,
811, 812, 813, 814
PANASONIC 818
RCA 805, 819
S. ATLANTA 815, 816, 817
To control a tuner
Maker Code(s)
SONY 002, 003, 004, 005
50
US
STR-DE695 4-247-631-11 (1) US
Additional Information
If you have any question or problem concerning your
receiver, please consult your nearest Sony dealer.
Troubleshooting
If you experience any of the following
difficulties while using the receiver, use this
troubleshooting guide to help you remedy the
problem. Also, see “Checking the connections”
on page 22 to verify that the connections are
correct.
There is no sound or only a very low-level sound
no matter which component is selected.
Check that the speakers and components are
connected securely and correctly.
Check that both the receiver and all the
components are turned on.
Check that the MASTER VOLUME control is
not set at “VOL MIN”.
Check that the SPEAKERS (OFF/A/B/A+B)
button is not set to off and is set accordingly to
your SPEAKERS FRONT system (page 24).
Press MUTING on the remote to cancel the
muting function.
Check that the headphones are not connected.
The protective device on the receiver has been
activated because of a short circuit (“PROTECT”
flashes). Turn off the receiver, eliminate the
short-circuit problem and turn on the power
again.
There is no sound from a specific component.
Check that the component is connected correctly
to the audio input jacks for that component.
Check that the cord(s) used for the connection is
(are) fully inserted into the jacks on both the
receiver and the component.
Check that you have selected the correct
component on the receiver.
Precautions
On safety
Should any solid object or liquid fall into the cabinet,
unplug the receiver and have it checked by qualified
personnel before operating it any further.
On power sources
Before operating the unit, check that the operating
voltage is identical with your local power supply.
The operating voltage is indicated on the nameplate
at the rear of the receiver.
The unit is not disconnected from the AC power
source (mains) as long as it is connected to the wall
outlet, even if the receiver itself has been turned off.
If you are not going to use the receiver for a long
time, be sure to disconnect the receiver from the
wall outlet. To disconnect the AC power cord, grasp
the plug itself; never pull the cord.
One blade of the plug is wider than the other for the
purpose of safety and will fit into the wall outlet
only one way. If you are unable to insert the plug
fully into the outlet, contact your dealer.
AC power cord must be changed only at the
qualified service shop.
On heat buildup
Although the unit heats up during operation, this is
not a malfunction. If you continuously use this unit at
a large volume, the cabinet temperature of the top,
side and bottom rises considerably. To avoid burning
yourself, do not touch the cabinet.
On placement
Place the receiver in a location with adequate
ventilation to prevent heat buildup and prolong the
life of the receiver.
Do not place the receiver near heat sources, or in a
place subject to direct sunlight, excessive dust or
mechanical shock.
Do not place anything on top of the cabinet that
might block the ventilation holes and cause
malfunctions.
Use caution when placing the unit on surfaces that
have been specially treated (with wax, oil, polish,
etc.) as staining or discoloration of the surface may
result.
On operation
Before connecting other components, be sure to turn
off and unplug the receiver.
On cleaning
Clean the cabinet, panel and controls with a soft cloth
slightly moistened with a mild detergent solution. Do
not use any type of abrasive pad, scouring powder or
solvent such as alcohol or benzine.
Additional Information
51
US
STR-DE695 4-247-631-11 (1) US
There is no sound from the active sub woofer.
Check that the sub woofer is connected correctly
and securely.
Make sure the sub woofer selection parameter is
set to “YES” (page 18).
There is no sound output from the SUB
WOOFER terminal depending on the sound field
(page 58).
The surround effect cannot be obtained.
Make sure the sound field function is on (press
MOVIE or MUSIC).
Dolby Digital or DTS multi channel sound is not
reproduced.
Check that the playing DVD, etc. is recorded in
Dolby Digital or DTS format.
When connecting the DVD player, etc. to the
digital input jacks of this receiver, check the
audio setting (settings for the audio output) of the
connected component.
Recording cannot be done.
Check that the components are connected
correctly.
Select the source component with input selector
buttons.
Make sure that INPUT MODE is set to
“ANALOG” before recording from a digital
component connected to the analog MD/TAPE
terminals.
Make sure that INPUT MODE is set to “COAX
IN” or “OPT IN” (page 23) before recording
from a digital component connected to the
DIGITAL MD/TAPE OUT terminals.
There is no sound from one of the front
speakers.
Connect a pair of headphones to the PHONES jack
to verify that sound is output from the headphones
(page 24).
If only one channel is output from the headphones,
the component may not be connected to the
receiver correctly. Check that all the cords are fully
inserted into the jacks on both the receiver and the
component.
If both channels are output from the headphones,
the front speaker may not be connected to the
receiver correctly. Check the connection of the
front speaker which is not outputting any sound.
The left and right sounds are unbalanced or
reversed.
Check that the speakers and components are
connected correctly and securely.
Adjust balance parameters in the LEVEL menu.
There is severe hum or noise.
Check that the speakers and components are
connected securely.
Check that the connecting cords are away from a
transformer or motor, and at least 3 meters away
from a TV set or fluorescent light.
Move your TV away from the audio components.
The plugs and jacks are dirty. Wipe them with a
cloth slightly moistened with alcohol.
There is no sound or only a very low-level sound
is heard from the center or/and surround
speakers.
Make sure the sound field function is on (press
MOVIE or MUSIC).
Select a sound field containing the word
“C.ST.EX” (pages 26–27).
Adjust the speaker level (page 22).
Make sure the center or/and surround speaker
size parameter is set to either “SMALL” or
“LARGE” (page 19).
continued
52
US
STR-DE695 4-247-631-11 (1) US
Outdoor FM antenna
Receiver
Ground wire
(not supplied)
To ground
y
AM
FM
75
COAXIAL
ANTENNA
There is no picture or an unclear picture appears
on the TV screen or monitor.
Select the appropriate input selector on the
receiver.
Set your TV to the appropriate input mode.
Move your TV away from the audio components.
The remote does not function.
• The TV/SAT, PHONO, SOURCE, DIRECT,
AAC BI-LING, 12 and ON SCREEN buttons on
the remote are not available.
Check that the command mode of the remote
corresponds to that of the receiver. If the
command mode of the receiver and the remote is
different, you cannot use the remote to operate
the receiver (pages 39 and 46).
Press MAIN MENU on the remote before you
use the V/v/B/b buttons for receiver operation.
To activate the buttons with orange printing,
press ALT first before pressing the buttons.
Point the remote at the remote sensor g on the
receiver.
Remove any obstacles in the path between the
remote and the receiver.
Replace both batteries in the remote with new
ones, if they are weak.
Make sure you select the correct input selector
on the remote.
If the remote is set to operate the TV only, use
the remote to select a source or component other
than TV before operating the receiver or other
component.
If you are unable to remedy the
problem using the troubleshooting
guide
Clearing the receiver’s memory may remedy
the problem (page 17). However, note that all
memorized settings will be reset to their factory
settings and you will have to readjust all
settings on the receiver.
If the problem persist
Consult your nearest Sony dealer.
Clearing the receiver’s memory
To clear See
All memorized settings page 17
Customized sound fields page 33
The FM reception is poor.
Use a 75-ohm coaxial cable (not supplied) to
connect the receiver to an outdoor FM antenna as
shown below. If you connect the receiver to an
outdoor antenna, ground it against lightning. To
prevent a gas explosion, do not connect the ground
wire to a gas pipe.
Radio stations cannot be tuned in.
Check that the antennas are connected securely.
Adjust the antennas and connect an external
antenna if necessary.
The signal strength of the stations is too weak
(when tuning in with automatic tuning). Use
direct tuning.
Make sure you set the tuning interval correctly
(when tuning in AM stations with direct tuning).
No stations have been preset or the preset
stations have been cleared (when tuning by
scanning preset stations). Preset the stations
(page 35).
Press DISPLAY so that the frequency appears in
the display.
Troubleshooting (continued)
Additional Information
53
US
STR-DE695 4-247-631-11 (1) US
Specifications
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
With 8 ohm loads, both channels driven, from
20 – 20,000 Hz; rated 90 watts per channel
minimum RMS power, with no more than
0.09 % total harmonic distortion from 250
milliwatts to rated output (models of area code
U only).
Amplifier section
POWER OUTPUT
Models of area code U, CA
Rated Power Output at Stereo Mode
(8 ohms 20 Hz – 20 kHz, THD 0.09 %)
90 W + 90 W
Reference Power Output
(8 ohms 20 Hz – 20 kHz, THD 0.09 %)
FRONT
1)
: 90 W/ch
CENTER
1)
: 90 W
SURR
1)
: 90 W/ch
SURR BACK
1)
: 90 W
(8 ohms 1 kHz, THD 0.7 %)
FRONT
1)
: 100 W/ch
CENTER
1)
: 100 W
SURR
1)
: 100 W/ch
SURR BACK
1)
: 100 W
1) Depending on the sound field settings and the
source, there may be no sound output.
Frequency response
MULTI CH IN,
CD/SACD, AUX,
MD/TAPE, DVD,
VIDEO 1, 2, 3
Inputs (Analog)
MULTI CH IN,
CD/SACD, AUX,
MD/TAPE, DVD,
VIDEO 1, 2, 3
2) INPUT SHORT (with sound field and equalizer
bypassed).
3) Weighted network, input level.
Inputs (Digital)
DVD (Coaxial) Sensitivity: –
Impedance: 75 ohms
S/N: 100 dB
(A, 20 kHz LPF)
VIDEO 2, CD/SACD, Sensitivity: –
MD/TAPE (Optical) Impedance: –
S/N: 100 dB
(A, 20 kHz LPF)
Outputs (Analog)
MD/TAPE (OUT), Voltage: 500 mV
VIDEO 1 (AUDIO OUT) Impedance: 10 kilohms
SUB WOOFER Voltage: 2 V
Impedance: 1 kilohms
Outputs (Digital)
MD/TAPE (Optical) Sensitivity: –
EQ
Gain levels: ±10 dB, 0.5 dB step
10 Hz – 70 kHz
+0.5/–2 dB (with sound
field and equalizer
bypassed)
continued
Sensitivity: 500 mV
Impedance: 50 kilohms
S/N
2)
: 96 dB
(A, 500 mV
3)
)
54
US
STR-DE695 4-247-631-11 (1) US
Specifications (continued)
FM tuner section
Tuning range 87.5 - 108.0 MHz
Antenna terminals 75 ohms, unbalanced
Intermediate frequency
10.7 MHz
Sensitivity
Mono: 18.3 dBf, 2.2 µV/75 ohms
Stereo:
38.3 dBf, 22.5 µV/75 ohms
Usable sensitivity 11.2 dBf, 1 µV/75 ohms
S/N
Mono: 76 dB
Stereo: 70 dB
Harmonic distortion at 1 kHz
Mono: 0.3%
Stereo: 0.5%
Separation 45 dB at 1 kHz
Frequency response 30 Hz – 15 kHz,
+0.5/–2 dB
Selectivity 60 dB at 400 kHz
AM tuner section
Tuning range
Models of area code U, CA
With 10-kHz tuning scale: 530 – 1710 kHz
4)
With 9-kHz tuning scale: 531 – 1710 kHz
4)
Antenna Loop antenna
Intermediate frequency
450 kHz
Usable sensitivity 50 dB/m (at 1,000 kHz or
999 kHz)
S/N 54 dB (at 50 mV/m)
Harmonic distortion 0.5 % (50 mV/m, 400 Hz)
Selectivity
At 9 kHz: 35 dB
At 10 kHz: 40 dB
4) You can change the AM tuning scale to 9 kHz or
10 kHz. After tuning in any AM station, turn off
the receiver. Hold down PRESET TUNING + and
press ?/1. All preset stations will be erased when
you change the tuning scale. To reset the scale to
10 kHz (or 9 kHz), repeat the procedure.
Additional Information
55
US
STR-DE695 4-247-631-11 (1) US
AC outlets 1 switched,
120 W/1A MAX
Dimensions 430 × 157.5 × 310 mm
(16 7/8 × 6 2/8 × 12 2/8
inches) including
projecting parts and
controls
Mass (Approx.) 8.0 kg (17 lb 11 oz)
Supplied accessories
FM wire antenna (1)
AM loop antenna (1)
Remote commander (1)
R6 (size-AA) batteries (2)
For details on the area code of the component you
are using, see page 4.
Design and specifications are subject to change
without notice.
Video section
Inputs
Video: 1 Vp-p, 75 ohms
S-video: Y: 1 Vp-p, 75 ohms
C: 0.286 Vp-p, 75 ohms
Component Video:
Y: 1 Vp-p, 75 ohms
P
B
/B-Y: 0.7 Vp-p, 75 ohms
PR/R-Y: 0.7 Vp-p, 75 ohms
Outputs
Video: 1 Vp-p, 75 ohms
S-video: Y: 1 Vp-p, 75 ohms
C: 0.286 Vp-p, 75 ohms
Component Video:
Y: 1 Vp-p, 75 ohms
P
B
/B-Y: 0.7 Vp-p, 75 ohms
PR/R-Y: 0.7 Vp-p, 75 ohms
General
Power requirements
Area code Power requirements
U, CA 120 V AC, 60 Hz
Power consumption
Area code Power consumption
U 245 W
CA 330 VA
Power consumption (during standby mode)
0.3 W (when “P.SAVE” in the CUSTOM menu is set
to “ON”) (page 39).
56
US
STR-DE695 4-247-631-11 (1) US
Tables of settings using the MAIN MENU button
You can make various settings using the MAIN MENU, / buttons and jog dial. The tables
below show each of the settings that these buttons can make.
Press MAIN MENU Press or to select Turn jog dial to select Page
repeatedly to select
LEVEL
L
R
BAL. L/R XX L +8 to R +8 (1 steps) 32
CTR XXX.X dB –10 dB to +10 dB (0.5 dB steps)
SUR.L.XXX.X dB –10 dB to +10 dB (0.5 dB steps)
SUR.R.XXX.X dB –10 dB to +10 dB (0.5 dB steps)
SB XXX.X dB –10 dB to +10 dB (0.5 dB steps)
S.W. XXX.X dB –10 dB to +10 dB (0.5 dB steps)
D. RANGE
COMP. XXX OFF, STD, MAX
EFCT. XXX depends on the sound field
(MIN, STD, MAX)
EQ BASS XXX.X dB –10 dB to +10 dB (0.5 dB steps) 33
TREB. XXX.X dB –10 dB to +10 dB (0.5 dB steps)
EQ XXX ON, OFF
SET UP
SW
(SUB WOOFER) S.W. XXX YES, NO 18
L
R
(FRONT) XXXXX LARGE, SMALL
C
(CENTER) XXXXX LARGE, SMALL, NO
SL
SR
(SURROUND) XXXXX LARGE, SMALL, NO
S B
(SURR BACK) XXX YES, NO
L
R
DIST. XX ft. between 3 ft. and 23 ft. (1 foot steps)
C
DIST. XX ft. between
L
R
DIST. and 5 ft.
(1 foot steps)
SL
SR
DIST. XX ft. between
L
R
DIST. and 15 ft.
(1 foot steps)
S B
DIST. XX ft. between
L
R
DIST. and 15 ft.
(1 foot steps)
SL
SR
XXXXXXX SIDE/LO, SIDE/HI, BEHD/LO, BEHD/HI
CUSTOM SB XXXX MTRX, AUTO, OFF 39
DEC. XXXX AUTO, PCM
P.SAVE.XXX ON, OFF
Additional Information
57
US
STR-DE695 4-247-631-11 (1) US
<EQ >
BASS TREB. EQ ON/OFF
2CH ST. zzz
A.F.D. AUTO zzz
DOLBY PL zzz
PLII MOV zzz
PLII MUS zzz
NEO6 CIN
NEO6 MUS
C.ST.EX A zzz
C.ST.EX B zzz
C.ST.EX C zzz
HALL zzz
JAZZ zzz
CONCERT zzz
MULTI CH IN
HP 2CH zzz
HP MULTI
HP THEA zzz
PCM 96K
Adjustable parameters for each sound field
The adjusted BASS and TREB. parameters are applied to all sound fields.
continued
58
US
STR-DE695 4-247-631-11 (1) US
1)
These parameters may not operate depending on the source or adjustments. For details, see each item in
“Adjusting the level parameters” (page 32).
2)
When these sound fields are selected, there is no sound output from the sub woofer if the front speaker size is set
to “LARGE”. However, sound will be output from the sub woofer if the digital input signal contains LFE
signals.
The adjusted LEVEL parameters are applied to all the sound fields except for EFCT. parameter. For
EFCT. parameter, the settings are stored individually for each sound field.
< LEVEL >
FRONT CENTER SUR.L. SUR.R. SURR BACK S.W. D.RANGE EFCT.
BAL LEVEL LEVEL LEVEL LEVEL LEVEL COMP
1)
LEVEL
2CH ST. zz
A.F.D. AUTO zzzz z zz
DOLBY PL zzzz z zz
PLII MOV zzzz z zz
PLII MUS zzzz z zz
NEO6 CIN zzzz z z
2)
z
NEO6 MUS zzzz z z
2)
z
C.ST.EX A zzzz z zzz
C.ST.EX B zzzz z zzz
C.ST.EX C zzzz z zzz
HALL zzzz zz
2)
zz
JAZZ zzzz zz
2)
zz
CONCERT zzzz zz
2)
zz
MULTI CH IN zzzz z
HP 2CH zz
HP MULTI z
HP THEA zzz
PCM 96K z
Adjustable parameters for each sound field (continued)
Additional Information
59
US
STR-DE695 4-247-631-11 (1) US
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sony STR-DE695 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sony STR-DE695 in the language / languages: English as an attachment in your email.

The manual is 1,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info