699866
89
Zoom out
Zoom in
Previous page
1/97
Next page
SNT-EX101/SNT-EX104/SNT-EP104
Others
Assigning the IP Address to the unit using ARP Commands
89
Record event: Type of event used for the
recording: Sensor input, Camera tampering
detection, VMF, Motion detection, Audio
detection, Network disconnection.
Playing a video/audio file
Click (start) to start playback from the beginning of
the selected file.
To freeze the movie temporarily, click (pause).
Click again to resume playback from the freeze
point.
To stop playback, click (stop).
To start playback from the beginning, click (start)
again.
Playback stops when the file is played to the end.
Playing from a specified point
Move the slider bar below the image display, and
playback will start from the position of the slider bar.
Adjusting the sound
Adjust the playing sound volume by moving the
slider bar. Move it to the left end for minimum
volume, and to the right end for maximum volume.
Click (speaker) to enable/disable sound (muting).
When sound muting is on, no sound will be heard, even
if you move the slider bar.
Saving an image
Click the (capture) icon during playback or pause
and the captured image is displayed in a pop-up dialog.
To save the image, click Save on the dialog. You can
specify the destination to which the image is to be
stored, and select the JPEG or Bitmap format.
How to change the image display size
Click × 1/4, × 1/2, × 1, × 2 or Full at the top of the image
to display the image in the selected magnification.
If you select × 1, the image is displayed in the
original image display size of the file.
The × 2 button is only available when image size is
640 × 480 (VGA) or smaller.
The selected image display size is highlighted.
Assigning the IP
Address to the unit
using ARP Commands
This section explains how to assign an IP address to the
unit using ARP (Address Resolution Protocol)
commands without using the supplied SNC toolbox.
Note
When you turn on the camera, execute the ARP and
PING commands within 5 minutes. Also when you
restart the camera, execute the operation within 5
minutes.
1
Open the command prompt on the computer.
When using Windows Vista or Windows 7, right
click Command prompt in Start-All Programs-
Accessories, and select Run as administrator.
2
Enter the IP address and the MAC address of the
video network station to assign a new IP address,
using the following ARP commands.
Example:
3
When the following line is displayed on the
command prompt, hold down Ctrl and press C.
Display stops.
You will normally receive a reply after about 5
repetitions of “Request time out.”
4
Wait until the execution of PING finishes, then
input the following code.
Note
If you do not receive a reply, check the following:
Did you enter the ARP commands within 5 minutes
after it was turned on?
If not, turn off the camera and restart the operation.
Is the NETWORK indicator on the camera flashing?
If the indicator goes off, the network connection has a
problem. Connect the network correctly.
Did you enter the IP address previously used for
another device?
Assign a new IP address to the camera.
arp -s <Camera's IP address> <Camera's MAC address>
ping -t <Camera's IP address>
arp -s 192.168.0.100 08-00-46-21-00-00
ping -t 192.168.0.100
Reply from 192.168.0.100:bytes=32 time...
arp -d 192.168.0.100
89


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sony SNT-EP154 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sony SNT-EP154 in the language / languages: English as an attachment in your email.

The manual is 3,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sony SNT-EP154

Sony SNT-EP154 User Manual - German - 107 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info