Manual Sony SDM-X82 (page 20 of 180) (English, German, Dutch, French, Italian, Swedish, Spanish)

47923

Zoom out

Zoom in

1/180

D:\###Sagyou\07 July\0709(TUE)-Night\821296S SDM-X52X72X82\4089157231 SDM-

X52X72X82\01GB-SDMX52AEP\01GB02BAS-AEP.fm

masterpage:Left

SDM-X52/X72/X82

4-089-157-23(1)

Trouble symptoms and remedies

If a problem occurs as a result of a connected computer or other equipment, refer to the connected computer/equipment’s instruction manual.

Use the self-diagnosis function (page 22) if the following recommendations do not resolve the problem.

Symptom Check these items

No picture

If the 1 (power) indicator is not lit,

or if the 1 (power) indicator will not

light up when the 1 (power) switch

is pressed,

• Check that the power cord is properly connected.

• Check that the monitor’s MAIN POWER switch is “on” (page 9).

The

(power) indicator turns on red.

• Check that the 1 (power) switch is on.

If the 1 (power) indicator is green, • Use the self-diagnosis function (page 22).

If CABLE DISCONNECTED

appears on the screen,

• Check that the video signal cable is properly connected and all plugs are firmly seated in

their sockets (page 7).

• Check that the video input connector’s pins are not bent or pushed in.

• Check that the input select setting is correct (page 11).

• A non-supplied video signal cable is connected. If you connect a non-supplied video

signal cable, CABLE DISCONNECTED may appear on the screen before entering the

power saving mode. This is not a malfunction.

If NO INPUT SIGNAL appears on

the screen, or the 1 (power)

indicator is orange,

• Check that the video signal cable is properly connected and all plugs are firmly seated in

their sockets (page 7).

• Check that the video input connector’s pins are not bent or pushed in.

• Check that the input select setting is correct (page 11).

xProblem caused by a connected computer or other equipment, and not

caused by the monitor

• The computer is in the power saving mode. Try pressing any key on the keyboard or

moving the mouse.

• Check that your graphics board is attached to the computer properly.

• Check that the computer’s power is “on.”

If OUT OF SCAN RANGE appears

on the screen (page 19),

xProblem caused by a connected computer or other equipment, and not

caused by the monitor

• Check that the video frequency range is within that specified for the monitor. If you

replaced an old monitor with this monitor, reconnect the old monitor and then adjust the

computer’s graphics board in the following ranges.

Horizontal frequency: 28 – 61 kHz (SDM-X52) 28 – 92 kHz (SDM-X72/X82)

Vertical frequency: 56 – 75 Hz (SDM-X52) 56 – 85 Hz (SDM-X72/X82)

Resolution: 1024 × 768 or less (SDM-X52) 1280 × 1024 or less (SDM-X72/X82)

If using Windows,

• If you replaced an old monitor with this monitor, reconnect the old monitor and do the

following. Select “SONY” from the “Manufacturers” list and select “SDM-X52” or “SDM-

X72” or “SDM-X82” from the “Models” list in the Windows device selection screen. If “SDM-

X52” or “SDM-X72” or “SDM-X82” does not appear in the “Models” list, try “Plug & Play”

or install the information file for this monitor using the Windows Monitor Information Disk.

If using a Macintosh system, • When connecting a Macintosh computer, use an adapter (not supplied) if necessary.

Connect the adapter to the computer before connecting the video signal cable.

Picture flickers, bounces,

oscillates, or is scrambled.

• Adjust the pitch and phase (analog RGB signal only) (page 13).

• Isolate and eliminate any potential sources of electric or magnetic fields such as other

monitors, laser printers, electric fans, fluorescent lighting, or televisions.

• Move the monitor away from power lines or place a magnetic shield near the monitor.

• Try plugging the monitor into a different AC outlet, preferably on a different circuit.

• Change the orientation of the monitor.

xProblem caused by a connected computer or other equipment, and not

caused by the monitor

• Check your graphics board manual for the proper monitor setting.

• Confirm that the graphics mode (VESA, Macintosh 19'' Color, etc.) and the frequency of the

input signal are supported by this monitor. Even if the frequency is within the proper range, some

graphics boards may have a sync pulse that is too narrow for the monitor to sync correctly.

• This monitor does not process the interlace signals. Set for progressive signals.

• Adjust the computer’s refresh rate (vertical frequency) to obtain the best possible picture

(60 Hz is recommended).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Sony SDM-X82 in the language / languages: English, German, Dutch, French, Italian, Swedish, Spanish as an attachment in your email.

The manual is 4,36 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Sony SDM-X82 Manual

Product: