625890
112
Zoom out
Zoom in
Previous page
1/124
Next page
112
The recorder automatically starts
recording when the satellite receiver is
turned on.
, The Synchro-Rec function was activated.
Turn off the satellite receiver and cancel the
Synchro-Rec function (page 61).
You dubbed a title, but the title did not
appear in the HDD Title List.
, The title contained a copy protection signal,
so it was moved (page 84).
High-speed dubbing is not possible.
, The title cannot be dubbed at high-speed
(page 83). Even if A-B erasure is performed
so that a title does not contain mixed picture
sizes, it is still treated as a title with mixed
picture sizes.
The clock has stopped.
, Set the clock again (page 96).
, The clock stopped due to a power failure
that lasted for more than 1 hour. Reset the
clock (page 96).
The TIMER REC indicator is flashing.
, The disc does not have enough space.
, Insert a recordable disc inside the recorder.
, The inserted DVD is protected (page 40).
The recording mode indication is
incorrect.
, When the recording or dubbing is less than
ten minutes, or if a picture with little
movement is displayed for more than ten
minutes, the recording mode indication may
be displayed incorrectly. Note that the
actual recording or dubbing itself was
correctly made in the selected recording
mode.
, After playing titles recorded in EP and SLP
mode, the recording mode indication may
change depending on the recorded
programme.
The clock does not appear in the front
panel display when the recorder is turned
off.
, “Dimmer” in the “Others” setup is set to
“Save Power” (page 105).
The remote does not function.
, Batteries are weak.
, The remote is too far from the recorder.
, The remote’s manufacturer code returned to
the default setting when you replaced the
batteries. Reset the code (page 21).
, The remote is not pointed at the remote
sensor on the recorder.
, Different command modes are set for the
recorder and remote. Set the same
command mode (page 22). The default
command mode setting for this recorder and
the supplied remote is DVD3.
, Press x (stop) on the unit while the
recorder is turned off to check the current
command mode.
The recorder does not operate properly.
, Restart the recorder. Press down [/1 on the
recorder for more than ten seconds until
“WELCOME” appears in the front panel
display.
, When static electricity, etc., causes the
recorder to operate abnormally, turn off the
recorder and wait until the clock appears in
the front panel display. Then, unplug the
recorder and after leaving it off for a while,
plug it in again.
Five numbers or letters are displayed in
the front panel display.
, The self-diagnosis function was activated
(see the table on page 114).
The disc tray does not open after you press
Z (open/close).
, It may take a few seconds for the disc tray
to open after you have recorded or edited a
DVD. This is because the recorder is adding
disc data to the disc.
Dubbing
Display
Remote control
Others
112


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sony RDR-HX525 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sony RDR-HX525 in the language / languages: English as an attachment in your email.

The manual is 7,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info