136405
34
Zoom out
Zoom in
Previous page
1/104
Next page
34 Chapter 2 Playback and Recording
Chapter 2 Playback and Recording
Connecting the unit to a monitor equipped
with an i.LINK jack
The video and audio signals are sent with hardly any
degradation, enabling high-quality playback to a
monitor with an i.LINK connector which supports
HDV, DVCAM, and DV format.
Notes
•Be sure that you set [HDV/DV SEL] in [IN/OUT
REC] menu to [AUTO] (default setting) before
connecting the monitor to the unit with the i.LINK
cable. If you change the setting after connecting the
i.LINK cable, the monitor may not recognize the
video signals correctly (page 67).
To connect the unit to a monitor equipped with an
i.LINK jack, you may need to set the monitor so that
it recognizes the unit.
For details, refer to your monitor’s instruction manual.
•When i.LINK is connected, the unit cannot output
video or audio only.
Notes
To playback the picture recorded in HDV format
when you connect the monitor using an HDMI cable
or a component video cable, set [HDMI/CMPNT] of
[VIDEO OUT] in [IN/OUT REC] menu according to
your monitor (page 68). When the picture recorded in
DVCAM/DV format is played back, only a picture
with a quality equivalent with DVCAM/DV format of
480i (NTSC) or 576i (PAL) is output via
COMPONENT OUT jacks regardless of [HDMI/
CMPNT] setting.
For details on output level from HDMI OUT jack and
COMPONENT OUT jacks, see “Specifications”
(page 100).
To change the output level from COMPONENT OUT
jacks, see [480i LEVEL] in [IN/OUT REC] menu
(page 71)
.
There are some restrictions on pictures output from
HDMI OUT jack and COMPONENT OUT jacks of
the unit.
Refer to HDMI OUT jack 6, COMPONENT OUT jacks
5 in “Rear Panel” of the “Location and Function of
Parts” on page 19.
If you connect the input connectors of the unit to the
output connectors of a monitor, a humming noise
may be generated or the image may be distorted. If
these phenomena occur, use INPUT SELECT switch
to select a signal that is not being input or disconnect
the cables.
• When you play back a tape with copyright protected
signals or input HDV signals with copyright
protection to
HDV/DV jack, pictures and audio are
not output via HDMI OUT jack.
• When you play back an HDV-formatted tape with
copyright protected signals or input i.LINK signals
with copyright protection to
HDV/DV jack, pictures
may be output in either 480i (NTSC) or 576i (PAL)
format regardless of the setting of [HDMI/CMPNT]
of [VIDEO OUT] in [IN/OUT REC] menu.
The unit cannot up convert DVCAM/DV recordings
to HDV at output.
Playback
HVR-M25 (rear panel)
i.LINK cable (not supplied)
i.LINK jack
Monitor with an
i.LINK jack
: Signal flow
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sony hvr m25p at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sony hvr m25p in the language / languages: English as an attachment in your email.

The manual is 0,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info